2013 Citroen C3 RHD parking brake

9
Driving
123

In exceptional circumstances, the gearbox may need an automatic reinitialisation: starting and gear changing are no longer possible.


Reverse

To e ngage reverse, the vehicle must be
immobilised with your foot on the brake.)Select position R.

Operating fault
With the ignition on, if this warninglamp comes on and AUTOflashes, accompanied by an audible signal and a message in the multifunction
screen, this indicates a gearbox
fault.Have it checked by a CITROËN
dealer or a qualified workshop.
At low speed, if reverse gear is requested,
the N warning lamp flashes and the gearboxgoes into neutral automatically.
To e ngage reverse, put the gear lever intoposition N, then to position R
.


Stopping the vehicle

Before switching off the engine:


- change to position N
to be in neutral,

or

- leave the vehicle in gear; in this case the
vehicle cannot be moved.
Reinitialisation
(5-speed electronic
gearbox)
Following disconnection of the battery, it isnecessary to reinitialise the gearbox.)
Switch on the ignition.
AUTO

and - -
appear in the
instrument panel.
) Select position N
. )
Press the brake pedal. )
Wait for around 30 seconds until N
or agear appears in the instrument panel.)
Move the gear lever to position A , then to
position N.) With your foot still on the brake pedal, start
the engine.
The gearbox is operational again.
AUTO and --
appear in the
instrument panel.

Follow the procedure described above.

Before doing anything under thebonnet, ensure that the gear lever is in neutral (position N ) and that the parkingbrake is applied.
There is an audible signal onengagement of reverse.

For all parking situations, you mustapply the parking braketo immobilise the vehicle.
When immobilising the vehicle with theengine running, you must put the gear lever into neutral (position N)
.

Driving
124














Automatic gearbox
1.
Gear lever.2.
Button "S"
(sport) . 3.Button "7"(snow).
Gear selection gate
P.Park.


- Immobilisation of the vehicle, parking brake on or off.

- Starting the engine.R.
Reverse.


- Reversing manoeuvres, vehicle stationary,engine at idle.
N.Neutral.


- Immobilisation of the vehicle, parking brake on.

- Star ting the engine.D.Automatic operation.

M + / - . Manual operation with sequentialchanging of the four gears.)
Push for wards to change up through the gears.
or ) Pull backwards to change down through
the gears.

Gear lever

When you move the lever in the gate to select
a position, the corresponding indicator isdisplayed in the instrument panel.P. Park R.ReverseN.
Neutral D.
Drive (Automatic driving)
S.Sport programme
7.Snowprogramme 1 2 3 4.
Gears engaged during manual
operation
-. Invalid value during manual operation


Displays in the instrument panel

Foot on brake
)
Press the brake pedal when this
indicator lamp is displayed in the
instrument panel (e.g.: star ting
the engine). Four-speed automatic
gearbox which offers a choice between the comfor t of fully automatic
operation, enhanced by spor t and snow programmes, or manual gear changing.
There are therefore four driving modes:-automaticoperation for electronic management of the gears by the gearbox, -
sport
programme for a more dynamic style
o
f driving,
- snowprogramme to improve driving when
traction is poor,
- sequential
operation for manual changing
of the gears by the driver.

9
Driving
125

Moving off
)Apply the parking brake. )Select position P
or N.)Star t the engine.
If this procedure is not followed, there is an
audible signal, accompanied by the display of
an warning message.)With the engine running, press the brake pedal. )Release the parking brake. )Select position R, Dor M.)Gradually release the brake pedal.
The vehicle moves off immediately.
Automatic operation
)
Select position Dfor automaticchangingof the four gears.
The gearbox then operates in auto-adaptive
mode, without any intervention on the par t
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
vehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal down
fully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
I
f you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes

These two special programmes supplement the
automatic operation in very specific conditions of use.

Sport programme "S"
)
Press button "S", after star ting the engine.
The gearbox automatically favours a dynamic style of driving.


Snow programme " 7"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.

Return to automatic
o
peration
) At any time, press the button selectedagain to quit the programme engaged and
return to auto-a
daptive mode.
S appears in the instrument panel.
7
appears in the instrument panel.
Never select position N
while the vehicle is moving.
Never select positions P
or Runless thevehicle is completely stationary.



If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.


When the engine is running at idle, with the brakes released, if position R, D
or M
is selected, the vehicle moves evenwithout the accelerator being pressed. When the engine is running, never leave children in the vehicle without supervision.
When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P

Driving
126
Manual operation
)Select position M for sequentialchanging
of the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to changedown a gear.
It is onl
y possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the instrument panel.


Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position Por N to place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle.

Operating fault
When the ignition is on, the lighting
o
f this warning lamp, accompanied by an audible signal and a message in the multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
To r e d u c e fuel consumption when at a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.



There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,


- if you force the movement of the gear lever from the P
position to another position when the battery is flat.
If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the message disappears.

If the en
gine speed is too low or too high, the gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically.
The spor t and snow programmes do not
operate in manual mode.

9
Driving
127
The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.


Operation
-with a manual gearbox
, at speeds below
12 mph (20 km/h), when you put the gear lever into neutral, and you release theclutch pedal.
-
with a 5 or 6-speed electronic gearbox
, at speeds below 5 mph (8 km/h), when you press the brake pedal or put the gear lever
in position N .



Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:
A tim
e counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition isswitched on with the key.


Special cases: STOP mode notavailable
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine star t using the key,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...
) where the engine isneeded to assure control of a system.
The "ECO"
warning lamp flashes for a few seconds then goes off.
This operation is perfectl
y normal.











Stop & Start
Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfor t, during parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...

Driving
130





Hill start assist
System which holds your vehicle temporarily (approximately 2 seconds) when star ting on a slope, the time it takes to move your foot from
the brake pedal to the accelerator pedal.
This
function is only active when:
- the vehicle is completely stationary, withyour foot on the brake pedal,
- cer tain conditions on a slope are met,
- with th
e driver’s door closed.
The hill start assist function cannot bedeactivated.
On an ascendin
g slope, with the vehiclestationary, the vehicle is held momentarilywhen you release the brake pedal:

- provided you are in automated mode (position A) or in manual mode (position AM)on an electronic gearbox.


Operating fault

If a malfunction of the system occurs, these
warning lamps come on. Contact a CITROËN
dealer or a qualified workshop to have thesystem checked. On a descendin
g slope, with the vehicle
stationary and reverse gear engaged, thevehicle is held momentarily when yourelease the brake pedal.
Do not leave the vehicle while it is being held in the hill star t assist phase.If you need to leave the vehicle with the engine running, manually applythe parking brake then ensure that theparking brake warning lamp is on (notflashing) in the instrument panel.


Operation

Checks
146
Manual gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for the details
of the level checking inter val for thiscomponent.
Automatic gearbox
The gearbox does not require anymaintenance (no oil change).
R
efer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of
the level checking inter val for thiscomponent.
Parking brake
If excessive travel or a loss of effectiveness of this system isnoticed, the parking brake must bechecked, even between two ser vices.
Electronic gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of thechecking inter val for this component.
















Brake pads

Brake disc wea
r
Brake wear depends on the style
of driving, par ticularly in the case
of vehicles used in town, over shor t
distances. It may be necessary to have
the condition of the brakes checked,
even between vehicle services.
For in
formation on checking brake
disc wear, contact a CITROËN dealer
or a quali
fied workshop.
















Only use products recommended by
CITROËN or products of equivalent quality and specification. In order to optimise the operationof units as impor tant as the braking system, CITROËN selects and offersvery specific products.

Unless there is a leak in the circuit, a drop in
the brake fluid level indicates that the brake
pads are worn.

Checking this system must be done by aCITROËN dealer or a qualified workshop.
After washing the vehicle, dampness,or in wintry conditions, ice, can form on the brake discs and pads: braking efficiency may be reduced. Make lightbrake applications to dry and defrost the brakes.

11
Practical information
155
Removing a wheel

List of operations
)
Remove the bolt cover from each of the bolts using the tool 3(with alloy wheels
only).) Fit the security bolt socket 4
on thewheelbrace 1to slacken the security bolt(if your vehicle has them).)
Slacken the other bolts using the
wheelbrace 1only.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off theignition and engage first gear *
to lock the wheels. If necessary, place a chock under thewheel diagonally opposite the wheel to be changed. It is imperative that you ensure that the occupants get out of the vehicle andwait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.
*
position R
for an electronic gearbox; position P
for an automatic gearbox.