Page 38 of 288
Monitoring
36
For a few seconds after the ignition is switched on,the spanner flashes to indicate that the service must be carried out as soon as possible.Example:the ser vice is overdue by 180 miles (300 km).
For a few seconds after the ignition is switched
on, the display indicates:
A few seconds after the ignition is switched
on, the distance recorder resumes its normaloperation. The spanner remains on.
Service indicator zero reset
After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition, )
press and hold the trip distance recorder
zero reset button, ) switch on the ignition; the distance recorder display begins a countdown, )
when the display indicates "=0", release
the button; the spanner disappears.
Retrieving the serviceinformation
You can access the ser vice information at anytime. )Press the trip distance recorder zero reset button.
The ser vice information is displayed for a
few seconds, then disappears.
The distance remaining may be weighted by the time factor, dependingon the driver's driving habits. Therefore, the spanner may also comeon if you have exceeded the period since the last service, indicated in the MAINTENANCE AND WARR ANT YGUIDE.
Following this operation, if you wish todisconnect the battery, lock the vehicleand wait at least five minutes for thezero reset to be taken into account.
Service overdue
Page 39 of 288
1
Monitoring
37
Engine oil level indicator
This information is displayed for a few seconds
when the ignition is switched on, after theservice information.
Oil level correct
This is indicated by the flashing of "OIL", linked with the ser vice warning lamp, accompanied
by an audible signal and a message in the
multifunction screen.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to prevent damage to the engine.
Oil level low
This is indicated by the flashing of "OIL--" . Contact a CITROËN dealer or a qualified
workshop.
Oil level indicator fault
Dipstick
There are 2 marks on the
dipstick:
- A= max; never exceed this
level (risk of damage to the engine), -B= min; top up the level via
the oil filler cap, using thegrade of oil suited to your engine. R
efer to the "Checks" section to locate the
dipstick and the oil filler cap on your engine.
The level shown will only be correctif the vehicle is on level ground and
the engine has been off for more than 30 minutes.
Page 40 of 288
Monitoring
38
System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displa
yed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
v
ehicle is locked or unlocked.
) With the ignition on, press the button until
zeros appear.
Tr ip distance recorder
System which measures a distance travelledduring a day or other period since it was reset
to zero by the driver.
Clock
Adjusting the time - Choice of units
To a djust the time of the clock and choose the
units used by the screen, use the right-hand
button on the instrument panel, carrying out the
operations in the following order: )press the button for more than two seconds:
the minutes flash, )press the button to increase the minutes, )press the button for more than two seconds:
the hours flash, )press the button to increase the hours, )press the button for more than two seconds:
24H or 12H is displayed, )press the button to select 24H or 12H, )press the button for more than two seconds: °C or °F is displayed, )press the button to select °C or °F, )press the button for more than two seconds
to complete the adjustments.
After approximately 30 seconds without anyaction, the screen returns to the normal display.
To c o nform to legislation in the country you are crossing, change the units of distance (miles or km) via theconfiguration menu.
Page 41 of 288
1
Monitoring
39
The instrument panel remains illuminated with
only the vehicle speed and cruise control or
speed limiter information, if in use.
If there is an aler t or a change in a function
or to a setting, the black panel mode is
interrupted.
Activation
) With the lighting on, press the left handbutton of the instrument panel several
times to progressively reduce the
dashboard lighting level.
) Press the button again to reduce the lighting to the minimum level and switch off
the interior mood lighting. ) Press the button again to activate the black
panel.
Black panel
System allowing cer tain displays to be switched
off for night driving.
Activation
When the lighting is on: )press the button to change the brightness
of the instruments and controls, )when the level of brightness required isreached, release the button.
Deactivation
When the lighting is off, or in day mode on
vehicles
fitted with daytime running lamps,pressing the button does not have any effect.
Lighting dimmer
System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
Page 42 of 288
Monitoring
40
Screen in the instrument panel
Monochrome screen A
Information displays
)
Press the button, located at the end of the wiper stalk
, to display the various items of
trip computer information in succession.
Zero reset
)Press the control for more than twoseconds to reset to zero the distancetravelled, the average fuel consumption
and the average speed.
The trip computer provides the following
information:
- ran
ge,
- current
fuel consumption,
- the Stop & Star t time counter * ,
- distance travelled,
- avera
ge fuel consumption,
)The next press then returns you to the normal display.
Tr i p c o m p u t e r
System that gives you information on
the journey in progress (range, fuel consumption…).
- avera
ge speed.
*
Available only with the monochrome screen A.
Page 43 of 288
1
Monitoring
41
Monochrome screen C
16/9 colour screen
(eMyWay)
Information displays
)Press the button, located at the end of
the wiper stalk
, to display the various tripcomputer tabs in succession:- th
e current information tabwith:
●
the ran
ge,
●
the current fuel consumption,
●
the distance remaining to
be travelled or the Stop &Start time counter,
- the trip "1"
t
ab with:
●
the distance travelled,
●
the avera
ge fuelconsumption,
●
the average speed,for the first trip.
- the tri
p "2"tab with:
●
the distance travelled,
●
the avera
ge fuelconsumption,
●
the average speed,
for the second trip.
)
Pressing the button again returns you to
the normal display.
Trip zero reset
)
When the trip required is displayed, press
the button on the end of the wiper stalk for more than two seconds.
Tr ips "1"
and "2"are independent but their use
is identical.
For example, trip "1"can be used for daily
figures, and trip "2"for monthly figures.
Page 44 of 288
Monitoring
42
Tr ip computer, a few definitions
Range
(miles or km)The distance which can still be
travelled with the fuel remainingin the tank. Related to theaverage fuel consumption over
the last few miles (kilometres)
travelled.
Current fuel consumption
(mpg or l/100 km or km/l) Calculated over the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip
computer reset.
Average speed
(mph or km/h)Calculated since the last trip computer reset.
Distance travelled
(miles or km)
Calculated since the last tripcomputer reset.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Distance remaining to destination
(miles or km)
This is the distance remaining to be
travelled to the final destination. Itcan be entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Stop & Start time counter
(minutes / seconds or hours /
minutes) If your vehicle is fitted with Stop &Start, a time counter calculates the
time spent in STOP mode during ajourney. It resets to zero every time the
ignition is switched on with the key.
If dashes are displayed continuously while driving in place of the digits, contact a CITROËN dealer or a qualified workshop.
This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
This function is only displayed from 20 mph (30 km/h).
Page 45 of 288
2
Multifunction screens
43
Monochrome screen A
This displays the following information:
- time,
- date,
- ambient temperature
(this flashes if there isa risk of ice),
- status of the doors and boot,
- audio sources
(radio, CD...),
- trip computer (refer to the "Instruments andControls" section).
Warning messages (e.g.: "Emission control system faulty") or information messages (e.g.:
"Boot open") may appear temporarily. Thesecan be cleared by pressing the "Back"button.
Controls
From the control panel of your Audio system,you can: )
press the "MENU"
button to gain access to
the main menu, )
press the "
" or " " buttons to scroll
through the items in the screen, ) press the "MODE"
button to change
the permanent application (date, audio source...), ) press the " " or " " buttons to change asetting value, )
press the "OK"button to confirm,or )
press the "Back"button to abandon the
operation in progress.
Main menu
)
Press the "MENU"
button to gain access to
the main menu
, then press the " "or " " buttons to scroll through the variousmenus:
- radio-CD,
- vehicle configuration,
- options,
- displa
y settings,
- languages,
- units. )
Press the "OK"button to select the menurequired.
Radio-CD
With the Audio system switched on, once the
"Radio- CD" menu has been selected you canactivate or deactivate the functions linked
with use of the radio (RDS, REG), or the CD(introscan, shuffle, CD repeat).
For more information on the "Radio-CD"
application, refer to the Audio system par t of
the "Audio and Telematics" section.
Displays in the screen
