Page 130 of 284
Driving
128
Display in the instrument panel
Gear lever positions
N. Neutral R. Reverse1, 2, 3, 4, 5, 6. Gears in manual mode. AUTO.
This comes on when the automatedmode is selected. It switches off on changing to manual mode.
Moving off
)
Select position N. )
Press the brake pedal down fully.
)
Start the engine.
Nappears in the instrument panel screen.
)
Select automated mode (position A
) or Amanual mode (position M ) or reverse(position R
).R )
Release the parking brake. )
Progressively take your foot off the brake
pedal.
) Accelerate away.
AUT
Oand 1 , 1 or Rappear in the instrument
panel screen.
Automated mode
)Select position A.
AUTOand the gear engaged appear
in the instrument panel screen.
The
gearbox operates in auto-active mode,
without any action on the par t of the driver. Itcontinuously selects the most suitable gear for:
- optimisation of fuel consumption,
- the style of driving,
- the profile of the road.
- the vehicle load.
For o
ptimum acceleration, for example
when over taking another vehicle, press the
accelerator pedal
firmly past the point of
resistance.
You must press the brake pedal whenstarting the engine.
Never select neutral N
when driving.
N
flashes in the instrument panel, accompanied by an audible signal and a message in the multifunction screen, if the gear lever is not in position Non starting.
A message is displayed in the screen, if the brake pedal is not pressed on starting the engine.
You can change mode at any time bymoving the gear lever from A
to Mor the other way round.
Page 131 of 284
9
Driving
129
) Select position M.
To engage reverse gear R
, the vehicle must be
immobilised with your foot on the brake pedal.
) Select position R.
At very low speed, if reverse gear is requested,
this will only be acted on when the vehicle is
immobilised.
At high speed, if reverse gear is requested,
the N indicator flashes and the gearbox goes into neutral. To engage a gear again, put thegear lever in position A
or M.
Te m p o r a ry control of gear changing
You can temporarily take over control of gear changing using the "+"and "-"
steering mounted paddles: if the engine speed allows,
the request to change gear is acted on.
This function allows you to anticipate cer tain situations such as over taking a vehicle or the
approach to a corner.
After a few moments without any action on
the control paddles, the gearbox resumes
automatic control of the gears. The
gears engaged appear in
succession in the instrument panelscreen.
The
gear change requests are only acted on if
the engine speed permits.It is not necessary to release the accelerator
during gear changes.
When brakin
g or slowing down, the gearbox changes down automatically to allow the
vehicle to accelerate in the correct gear. On sharp acceleration, the gearbox will notchange up unless the driver acts on the gear lever or the steering mounted paddles.
Never select neutral Nwhile the vehicle is moving.
You can change mode at any time, bemoving the gear lever from M to A
or the other way round.
Engagement of reverse gear isaccompanied by an audible signal.
Manual mode
Reverse
Page 132 of 284
Driving
130
Stopping the vehicle
Operating fault
With the ignition on, the flashing of AUTO ,
accompanied by an audible signal and a
message in the screen, indicates a malfunction
of the gearbox.
Have it checked by a CITROËN dealer or aqualified workshop.
In all cases when parking, you must apply the parking braketo immobilise the vehicle.
When immobilising the vehicle, with theengine running, you must place the gear lever in neutral N.
Before carrying out any work in the
engine compartment, ensure that the gear lever is in neutral N
and that theparking brake is applied. Be
fore switching off the engine, you can:
- move to position Nto engage neutral,
or
- leave the gear engaged; in this case, it will not be possible to move the vehicle.
Page 133 of 284
9
Driving
131
Hill start assist
(with the 6-speed
electronic gearbox
system)
System which holds your vehicle temporarily (approximately 2 seconds) when star ting on a slope, the time it takes to move your foot from
the brake pedal to the accelerator pedal.
This function is onl
y active when:
- the vehicle is completely stationary, with your foot on the brake pedal,
- certain conditions on a slope are met,
- with the driver’s door closed.
The hill start assist function cannot bedeactivated.On an ascendin
g slope, with the vehicle
stationar y, the vehicle is held momentarily
when
you release the brake pedal:- provided you are in automated mode(position A) or in manual mode (position AM )
on an electronic gearbox.On a descendin
g slope, with the vehicle
stationar y and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.
Operating fault
If a malfunction of the system occurs, these
warning lamps come on. Contact a CITROËN
dealer or a qualified workshop to have the system checked.
Do not leave the vehicle while it is being held in the hill star t assist phase. If you need to leave the vehicle withthe engine running, manually applythe parking brake then ensure that the parking brake warning lamp is on (not flashing) in the instrument panel.
Operation
Page 134 of 284
Driving
132
Stop & Start The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restar ts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
Operation
Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:
- with the 6-speed electronic
gearbox
system, at speeds below 5 mph (8 km/h),
when you press the brake pedal or put thegear lever in position N.
A time counter calculates thesum of the periods in STOP
mode during a journey. It rests
itself to zero every time the
ignition is switched on with thekey.
Special cases: STOP mode not available
STOP mode is not invoked when:
- the driver's door is open,
- the driver's seat belt is not fastened,
- the vehicle has not exceeded 6 mph(10 km/h) since the last engine start usingthe key,
- the engine is needed to maintain acomfortable temperature in the passenger compartment,
- demisting is active,
- some special conditions (battery charge,
engine temperature, braking assistance,ambient temperature...) where the engine isneeded to assure control of a system.
The "ECO"warning lamp flashes for
a few seconds then goes off.
This operation is per fectly normal.
Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfor t, during parkingmanoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...
Page 135 of 284
9
Driving
133
Going into engine START mode
The "ECO"warning lamp goes
off and the engine starts with theelectronic gearboxsystem:
- gear lever in position Aor M
, when yourelease the brake pedal,
- or gear lever in position N
and the brake pedal released, when you move the gear lever to position A
or M,
- or when you engage reverse gear.
Special cases: START invoked automatically
For reasons of safety and for your comfort,START mode is invoked automatically when:
- you open the driver's door,
- you unfasten the driver's seat belt,
- the speed of the vehicle exceeds 7 mph(11 k m/h) with the electronic gearbox system,
- some special conditions (battery charge,engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.
Th
e "ECO"
warning lamp flashes for
a
few seconds, then goes off.
This operation is per fectly normal.
Deactivation
At any time, press the "ECO OFF"
switch todeactivate the system.
This is confirmed by the switch warning lamp coming on accompanied by a message in the screen.
If the system has been deactivatedin STOP mode, the engine restar ts immediately.
Page 152 of 284
Checks
150
If excessive travel or a loss of effectiveness of this system is
noticed, the parking brake must be checked, even between two ser vices.
Manual gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the ser vicing booklet for the
details of the level checking inter val for this component.
For in
formation on checking brake
disc wear, contact a CITROËN dealer
or a qualified workshop.
Brake disc wear
Brake wear depends on the style
of driving, par ticularly in the case
of vehicles used in town, over shor t
distances. It may be necessary to have
the condition o
f the brakes checked, even between vehicle services.
Brake pads
The gearbox does not require anymaintenance (no oil change).
Refer to the servicing booklet for
details of the checking inter val for
this component.
Electronic gearbox
Only use products recommended by CITROËN or products of equivalent quality and specification.
In order to optimise the operationof units as impor tant as the braking system, CITROËN selects and offersvery specific products. Checkin
g this system must be done by a CITROËN dealer or a qualified workshop.
Unless there is a leak in the circuit, a drop in
the brake fluid level indicates that the brake pads are worn.
Page 182 of 284
Practical information
180
Charging the battery using
a battery charger
Load reduction mode
)Follow the instructions for use provided by
the manufacturer of the charger.
Do not disconnect the battery tocharge it.Do not push the vehicle to star t theengine if your vehicle is fitted with an electronic gearbox.
Batteries contain harmful substances suchas sulphuric acid and lead. They must be disposed of in accordance with regulationsand must not, in any circumstances, bediscarded with household waste.Ta k e used remote control batteries and vehicle batteries to a special collection point.
System which manages the use of certain
functions according to the level of charge
remaining in the battery.
When the vehicle is bein
g driven, the load
reduction function temporarily deactivates certain functions, such as the air conditioning,
the heated rear screen ...
Th
e deactivated functions are reactivated
automatically as soon as conditions permit.
