2013 AUDI TT key

Safety belt position
Correct be.It position is the key to getting
maximum protection from safety belts .
Fig. 1 01 Safety belt pos it io n
Standard features on yo ur vehicle help you ad­
just the position of the safety belt to match
your body size.
- height-adjustable front seats.
& WARNING
Improperly positioned safety belts can
cause serious personal injury in an acci­
dent.
-
- T he shoulder be lt shou ld lie as close to
the cente r of the collar bone as poss ible
and should fit we ll on the body . Ho ld the
belt above the latch tongue and pull it
evenly across the chest so that it sits as
low as possible on the pelvis and there is
no pressure on the abdomen. The be lt
should always fit snugly
c:> fig . 101 . Pull
on the belt to tighten if necessary .
- The lap belt port ion of the safety be lt
must be positioned as low as possible
across pelvis and never ove r the abdo­
me n. Ma ke su re the be lt lies flat and
snug
c:> fig. 101 . Pull on the belt to tight­
en if necessary .
- A loose-fi tt ing safety be lt c an cause seri­
o us inj uries by s hifting its position on
yo ur body from the strong bones to more
vulnerab le, soft tissue and cause serious
injury.
- Always read and heed all WARN INGS and
other important info rmation
c:> page 103.
Safety belts 105
Pregnant women must also be properly
, restrained
The best way to protect the fetus is to make
sure that expectant mothers always wear
safety belts corre ctly -throughout the preg­
nancy.
Fi g. 102 Safety be lt po sit ion d uring preg nancy
To provide max imum protect ion, safety belts
must a lways be positioned correctly on the
wearer 's body
c> page 105.
.,. Adjust the front seat and head restraint cor­
rectly
c:> p age 54 , General recommenda­
t ions .
.,. Make s ure the seatback of the rear seat
bench is in upright position and securely
latched in p lace befo re using the belt.
.,. Hold the belt by t he tongue and pull it
even ly across the ches t and pelv is
c> fig.10 2,c> .&., .
.,. Insert the tongue into the correct buck le of
your seat unti l yo u h ear it latch securely
<=> page 104, fig. 100 .
.,. Pull on the belt to make sure that it is se­
curely latched in the buck le.
& WARNING
Imp roperly posit ioned safety belts can
cause ser ious persona l inju ry in an acc i­
dent.
-
- Expectant mothers must always wear the
lap port ion of the safety belt as low as
possible a cross the pelvis and below the
round ing of the abdomen.
- Always read a nd heed all WAR NIN GS a nd
o ther impo rtant inform ation
c:> & in Fas­
tening safety belts on page 104.

than is being generated and ensures an opti­mal state of charge for the battery.
@ Tips
- But even energy management cannot
negate the limits o f physics. Consider
that the power and life of a battery are
li mited.
- If starting ab ility is threatened, you are
i nformed by a warning
¢ page 157,
Driver notification in the instrument
cluster display.
What you should know
The highest priority is given to maintaining
starting capability.
The battery is severely taxed in short-distance
driving, in city traffic and during the co ld time
of year. Abundant e lectrica l energy is re­
quired, but only a litt le is generated. It is also
cr itical if the engine is not run ning and electri­
cal components are turned on. In th is in­
stance energy is being consumed but non e is
be ing gene rated.
It is in precisely these situations that you w ill
notice energy management actively regulat ­
in g the distribution of energy .
Vehicle stands for an extended period
If you do not drive your vehicle over a period
of several days or weeks, electrical compo­
nents are gradually cut back or switched off.
This reduces energy consumption and mai n­
tains sta rting capab ility over a longer per iod.
Take into consideration that when you un lock
your ve hicle, some co nvenience functions,
such as the remote key or power seat adjust ­
ment, may not be available . The convenience
f u nctions w ill be ava ilable again whe n you
turn on the igni tion and star t the eng ine.
With the engine turned off
If you listen to the radio, for example, with
the eng ine turned off, the battery is being dis­
charged .
Intellig ent technolog y 157
If starting capability is jeo pardi zed d ue to en ­
ergy consumption, a message appears in the
drive r information d isplay .
You have to start t he engine to charge the
batte ry .
With the engine running
Although e lectrical energy is generated when
the ve hicl e is being driven, t he battery can be­
c ome disc harged. This happe ns mostly when
li ttle energy is being generated and a g reat
deal consumed and t he battery's sta te of
c h arge is not optimal.
T o b ring the energy b alance b ack into equili ­
br ium, consumers which requ ire espe cially
la rge amounts of energy a re temporari ly cut
back or switched off . Heating systems in pa r­
ticu lar require a great deal of energy. If yo u
notice, for example, that the heated seats* or
the heated rear window are not heating, they
have been temporarily cut back or sw itched
off . These systems w ill be available again as
soon as the ene rgy balance has been restored.
You w ill also notice that engine id le speed has
been increased slightly . T hi s is normal and not
a cause for conce rn . By i ncreas ing eng ine id le
speed the additional energy r equired is gene r­
ated and the battery is charged.
Driver notification in the instrument
cluster display
If battery power drops into the range where it
can limit the ability of the engine to start, this
is shown in the instrument cluster display
with the following driver message:
(•) Low battery charge: battery will be
charged while driving
T his no tificat ion reminds yo u that the star ting
capability of the engine may be lim ited . As
soon as you sta rt dr iving again, the battery
will be recharged and the not ificat ion w ill go
out. •
•

you have the engine washed, the anti-corro­sion treatment is a lmost always removed as
wel l. It is therefore essential to have a long­
lasting corrosion protection reapplied to all
surfaces, seams, joints and components in the
engine compartment .
A WARNING
Be aware: The engine compartment of any
motor vehicle is a potentially hazardous
area.
- Before working in the engine compart­
ment, be sure to read the informat ion
c::.>page 174.
- Before reaching into the front plenum
pane l, always remove the ignition key.
O therw ise, the windshield wipe r system
cou ld unintentiona lly be switched on,
poss ibly causing personal injury from the
moving wiper linkage .
- Never reach into the area around or
touch the radiator fan. The auxiliary fan
is temperature controlled and can switch
on suddenly- even when the ign it ion is
off.
- Do not wash, wax or dry the engine w ith
the engine running. Moving or hot parts could injure you .
- Do not clean the underside of the chas­ sis, fenders, wheel covers, or other hard
to reach parts w ithout protecting your
hands and arms. You may cut yourse lf on
sharp-edged metal parts .
- Always read and heed all WARNINGS and
other information
c::.> page 164.
Cleaning and protec tion 17 5
•
•

180 Checking and filling
Checking and filling
Engine hood
Releasing the engine hood
The engine hood is released from inside the
vehicle.
Fi g. 132 Dr iver's side footwell: engine hood re lease
lever
.. Open the driver's door.
.. Pull the release lever on the left under the
instrument panel
c> fig. 132 in the direction
of the arrow .
The hood pops up slight ly under spring pres­
sure.
Opening the engine hood
Fig . 133 Re lease lever under the engine hood
Before opening the engine hood, make sure
that the windshie ld wipers are flat against the
windshie ld. Otherwise, they cou ld damage the
pa int on the hood.
.. Lift the hood s light ly
c> _& .
.. Pull up on the release under the hood
¢ fig. 133. This releases the catch.
.. Open the hood all the way.
A WARNING
-Hot engine coolant can burn you.
- To reduce the risk of being burned, never
open the hood if you see or hear steam
or coo lant escaping from the eng ine
compartment. Wait unt il no steam or
coolant can be seen o r heard before care­
fu lly opening the hood.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced .
.. Let the hood
drop down and latch in p lace.
Do not try to push it shut; it may fail to en­
gage
c> _& .
A WARNING
--
A hood that is not completely latched
could fly up and b lock your view while dr iv­
i ng.
- When you close the engine hood, check it
to make sure the safety catch has proper­
ly engaged . The hood should be flush
with the surrounding vehicle body parts.
- If you notice while dr iv ing that the hood
is not secured properly, stop at once and
close it.
Working in the engine compartment
Be especially careful whenever you work in
the engine compartment!
Wheneve r you must pe rform any wo rk in the
eng ine compartment, for e xample chec king
and filling the different fluids, ther e is a risk
of injury, burns and a ccident s. To prevent
p ers onal injury al ways obs erv e the following
WARNINGS. The eng in e c ompartm ent of an y
vehicl e is a hazardou s area!
c> .&.
A WARNING
To he lp avoid injury, before yo u check any­
thing under the hood:
- Sw itch off the engine .
- Remove the ignition key.

228 Fuses and bulbs
Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through .
Fig. 164 End face of instrument panel: rem ov ing cover
p la te to access fuses
Fig. 165 Left side of eng ine compart men t: fuse cove r
Fuse cover on the left end face of the
inst rument pane l
.. Switch off the ignition and the electrical
component affected.
.. Carefully pry the fuse cover off the instru ­
ment panel using the ignition key or a
screwdriver~
fig. 164 .
.. Check the fuse listing on the next pages to
find out which fuse belongs to the compo­
nent which has failed
~ page 229, Fuse Lo­
cation, Instrument Panel left .
.. Remove the blown fuse with the plastic clip
provided. The cl ip is located on the holder in
the fuse box .
.. Replace a blown fuse (recognizable by the
melted metal str ip inside) with a fuse of the
same amperage .
.. Firmly snap the cover back onto the instru­
ment panel face .
Fuse cover in engine compartment
.. Switch the ignition and the affected con­
sumer off .
.. Unlatch the fuse cover, push the two slides
forward
~ fig. 165.
.. Find out which fuse belongs to the equip­
ment which stopped working~
page 230,
Fuse location , le~ side of engine compart­
ment .
.. Remove the plastic from its retainer in the
fuse box cover (left face end of the instru­
ment panel), place it on the fu se in question
and pull it out .
.. If the fuse is burned out (recognizable by
melted strips of metal), replace it with a
new fuse
of the same rating.
.. Replace the fuse cover.
.. Push the two slides to the rear~
fig. 165.
Install the fuse cover carefully to prevent
water from enter ing .
The various electrical circuits are protected by
fuses. The fuses are clustered in a centralized unit. The unit is located behind the face panel
at the end of the instrument panel.
You are well advised to keep a supply of spare
fuses in your vehicle. Fuses with the proper
ampere rat ings are ava ilable at your author ­
ized Audi dealer.
A WARNING -
Do not repa ir fuses and never replace a
blown fuse with one that has a higher amp
rating. This can cause damage to the elec­
trica l system and a fire.
(D Note
If a new fuse burns out again after shortly
have you have installed it, have the electri­
ca l system checked by your authorized
Audi dealer.

238 General information
General information Explanation of
technical data
Some of the technical data listed in this man ­
ual require further explanation.
The tecical data for your vehicle are listed in
the charts starting on ¢
page 240. This chap­
ter provides general information, notes and
restrictions which apply to these data .
Vehicle identification
The key data are given on the vehicle identifi­
cation number (VIN) plate and the vehicle da­
ta sticker.
Fig. 179 Veh icle Ide ntificat io n Number (VlN) plate: lo ­
cation on driver 's side das h panel
Fig. 180 Th e vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
ble from the outside through the windshield -
seer:!> fig. 179. You can also display the Vehi­
cle Identification Number of your vehicle in
the Driver Information display¢
page 24 .
The vehicle identification label
is located in the luggage compartment in the
spare wheel wel l.
The label¢
fig. 180 shows the following vehi­
cle data :
(D Product ion control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is your assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
time the vehicle was manufactured . You can
find this sticker on the left door jamb.
It
shows the month and year of production and
the ve hicle ident ification number of your vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carr ier .
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oi l and coolant, plus maximum load, wh ich in­
cludes passenger weight (150 lbs/68 kg per
Ill>

24 4 Con sum er Inf ormation
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Als o, sa fe ty a nd en vir onm ent al con­
cerns place very strict limits on the nature of
repairs and adjustments to engine and trans­
miss ion parts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment available to specially trained
workshop personnel in order to assure proper pe rformance, reliab ility and safety of the vehi­
cle and its many systems.
Improper maintenance, adjustments and re­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­
ranty. Therefore, proof of servic ing in accord­
ance w ith the ma intenance schedule may be a
condition for upholding a poss ible warranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any se rv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop.
We strong ly urge you to give yo ur autho rized
Audi dealer the opportunity to perfo rm all
schedu led maintenance and necessary repairs.
Your dea ler has the facilities, original parts
and trained specialists to keep your vehicle
running properly.
Performing limit ed m aint enance yours elf
The following pages describe a limited num­
ber of proced ures which can be performed on
your vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously obse rve the
WARNINGS p rovided.
Before you ch eck anything in th e eng ine
co mpartm ent , alway s re ad and h eed all
WA RNINGS
c::> .&. and c::> .&. in Working in the
engine compartment on page 180.
_& WARNING
- Serious personal injury may occur as a re­
sult of improperly performed mainte­
nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r is k personal
inju ry.
- Do not attempt any of the maintenance,
checks or repairs descr ibed on the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re ­
spect to the vehicle, or are uncertain how
to proceed .
- Do not do any work without the proper
too ls and equipment. Have the necessa ry
work done by your authorized A udi deal­
er or another proper ly equipped and
qualified workshop.
- The engine compartment of any motor
veh icle is a potentially hazardous area.
Never reach into the area around or
touch the radiator fan. It is temperature controlled and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatical ly when the
coo lant reaches a certain temperature
and will continue to run until the coo lant
temperature drops .
- Always remove the ign ition key before
anyone gets under the vehicle.
- Always support your vehicle with safety
stands if it is necessary to work under­
neath the vehicle. The jack supplied with
the vehicle is not adequate for this pur­
pose and cou ld collapse causing serious
personal injury.
- If you must work underneath the vehicle
with the wheels on the ground, always
make sure the vehicle is on leve l ground,
that the wheels a re a lways secure ly
b locked and that the engine cannot be
started.
- Always make sure the transmission se­
lector lever (automatic transmission) is

246 Consumer Information
Technical Modifications
Our guidelines must be complied with when technical modifications are made .
Always consult an authorized Audi dealer be­
fore starting work on any modifications.
This will help ensure that vehicle function,
performance and safety are not impaired
¢ &. .
Attempting to work on electronic components
and the software used with them can cause
malfunctions. Because of the way electronic
components are interconnected with each
other, such malfunctions can also have an ad­
verse affect on other systems that are not di­
rectly involved. This means that you risk both
a substantial reduction in the operational
safety of your vehicle and an increased wear of
ve hicle parts ¢
A:,..
Author ized Audi dealers will perform th is
wo rk in a professiona l and competent manner
or, in special cases, refer you to a professional
company that specializes in such modifica­
tions .
A WARNING
Improper repairs and modifications can
change the way vehicle systems work and
cause damage to the vehicle and serious
personal injury.
If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized Audi dealership as soon as
possible.
Declaration of Compliance, Telecommu­
nication or Electronic Systems
-
Radio Frequency Devices and Radiocommuni­
cation Equipment User Manual Notice.
The manufacturer is not responsible for any
radio or TV interference caused by unauthor­
ized modifications to th is equ ipment.
Devices
T he following devices each comply with FCC
Part 15.19, FCC Part 15.21 and RSS-Gen Issue
1:
- Cell phone package
- Electron ic immobilizer
- Homelink ® universal remote control
- Remote control key
FCC Part 15.19
This device complies with part 15 of the FCC
Rules . Operation is subject to the fo llowing
two conditions:
(1) This device may not cause harmful inter­
f erence, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
FCC Part 15.21
CAUTION:
Changes or modifications not expressly ap­
proved by the party responsible for compli­
ance could vo id the user's authority to operate
the equipment.
RSS-Gen Issue 1
Operation is subject to the following two con­
ditions:
(1) this device may not ca use interference,
and
(2) this device must accept any interference,
including interference that may cause unde­
s ired operation of the device.