come back a while later and drive off, the rain
sensor will reactivate itself after the vehicle
speed has exceeded 4 mph (6 km/h).
The rain sensor* is only activated with the
wiper lever set to position(!). When it starts
to rain, the rain sensor will automatically acti
vate the intermittent wiping mode.
To reduce the sensitivity of the sensor, move
switch @ down. To increase the sensitivity,
move the switch up. The higher you adjust the
sensitivity, the faster the sensor will react
when it senses moisture on the windshield. The pauses between wiper turns depend not
only on the sensitivity setting, but on the ve
hicle speed as well.
During brief stops, e.g . at a red light, wiper
motion will automatically be reduced to the
next lower speed . Wipers already turning at
low speed change to intermittent wiping.
When the ignition is turned on, the washer
jets are heated .
A WARNING
-Wiper blades are crucial for safe driving!
Only when they are in good condition are
they able to clear the windows properly
to provide uncompromising visibility.
Worn or damaged wiper blades are a
safety hazard
r=;, page 51, Replacing
windshield wiper blades!
- The light/rain sensor* is only designed to
assist and support the driver.
It remains
entirely the driver's responsibility to
monitor outside weather conditions and
to manually activate the wipers as soon
as rain or drizzle reduces visibility
through the windshield.
- The windshield must not be treated with
water-repellent materials. They can in
crease glare under poor visibility condi
tions such as wetness, darkness, or when
the sun is low on the horizon. In addi
tion, they can cause the windshield wip
ers to chatter.
Clear vision 49
@ Note
In freezing or near freezing conditions:
- Always check that the wiper blades are
not frozen to the glass before you turn
the wipers on. Loosen a wiper blade
which is frozen in place before operating
the wipers to prevent damage to the
wiper blade or the wiper motor.
- Do not use the wipers to clear a frosted
window. Using the wipers as a conven ient ice scraper will destroy the wiper
blades .
- Before you take your vehicle to an auto
matic car wash, make sure you have the
windshield wiper system switched off (lever in position
0), otherwise the wind
shield wiper system could get damaged
in the car wash if it should suddenly
come on.
@ Tips
-The windshield wipers are switched off
when the ignition is turned off. Activate
the windshield wipers after the ignition
is switched back on by moving the wind
shield wiper lever to any position.
- Worn or dirty windshield wiper blades
cause smearing, which can affect the op
eration of the light/rain sensor*. Check
the condition of your windshield wiper
blades regularly.
-The rain sensor is part of the interval
wiping system. Turning off the ignition
will also deactivate the rain sensor. To re
activate the sensor, switch off the inter
val wiping function, then switch it back
on again.
-Applies to vehicles with light/rain sen
sor: When the wipers are switched on
manually and in rain conditions, the au
tomatic headlights* turn on
r=;, page 42,
Switching the headlights on and off
or
off during the day when the wipers are
no longer operating. The automatic
headlights* function is available in this
case only when the light switch is in the
"AUTO" position¢
page 42, fig. 39.
50 Clear vis ion
- Make sure the washe r fl ui d reservoi r in
the engine compartment is topped
off
before going on a long t rip . L oo k up
c:> page 194 for checking and fi lling the
washer container.
- The w ipers only operate w ith the hood
completely closed.
Headlight washer system
App lies to vehicles : with hea dli ght washer syste m
The headlight washer system cleans the
headlights.
., Operate the windshield wiper/washer sys
tem
c:> page 48, fig. 50 ® with the head
li ghts turned on by holding the lever for lon
ger than one second.
The washe r jets extend forward o ut of the
front bumper driven by water pressure to
spray the front headlights with water.
You shou ld inspect the headlights regularly
(for example when refue ling) and clean
off
any solid dirt or insects from the lenses .
To ensure the system wo rks properly in winter,
keep the washer jets free o f snow and remove
any ice using a de- ic ing spray.
Service position
It is only possible to change wiper blades if
you move the wiper arms to the service posi
tion .
In o rder to use the windsh ie ld w ipers, the
front lid must be comp letely closed .
Moving wiper blades to the service
position
., When there is a ris k of frost, ma ke s ure that
the wiper b lades are not frozen to the wind
shield .
.. Switch the ignition on .
., Move the wiper lever to position
0
c:> page 48, fig. 50 .
., Press the I Re set I button until the D isplay
typ e
menu appears in the Driver Informa
t ion System display . .,
Using the rocker switch and the
I R ese t! but
ton, se lect the
Set > Wipe rs > Front > Serv
ice position on
funct ion . T he w indshield
w iper arms move to the service posit ion.
Mo ving wip er blades to pa rk position
., Ma ke certain that the w iper arms are ly ing
against the windshield .
., Switch the ignitio n on and move the wiper
lever from pos ition O
to 4 c:> page 48,
fig. 50. The w iper arms will move back to
the park position.
@ Note
Never drive your veh icle when the wind
sh ield wiper arms are in the service posi
tion and pulled away from the winds hield .
When you drive faster than
4 mph (6 km/
h), the wiper a rms automatically return to
the pa rk position and cou ld cause paint
damage to the front lid!
@ Tips
- Yo u can also tur n on the se rvice posit ion,
for example, if you want to p rotect the
w indshield from icing by us ing a cover.
- The service posit ion moves to
off auto
matically whe n you ope rate the w ind
shield wiper lever, o r speed exceeds
4 mph (6 km/h) .
72 On the road
you leave your veh icle . This makes a vehicle
theft even more difficult ¢ .&. .
Ignition ke y saf ety lock
After swi tching off the ignition, the ig nit ion
key can on ly be removed from the ign it ion
lock when the se lector lever is in the "P"
(Park) position . After you have removed the
key, the selector lever is locked and cannot be
moved.
Ignition on @
If it is diffic ult to turn the key after you have
inserted it into the ignition lock, turn the
steering wheel back and forth. This will take
the load
off the steering lock mechanism and
you will be able to turn the key freely and
start the engine.
Starting the engine @
In this position the engine starts . While the
engine is starting, the power supply to the headlights and other e lectrica l consumers is
temporari ly interrupted to conserve battery
power. After the engine has started, release
the key and it will return to posit ion
(D .
Before the starter can be operated again the
key must be turned back to position @. The
non -repeat loc k prevents you from damaging
the starter when the engine is runn ing .
A WARNING
-Never remove the key from the ign ition
lock whi le the vehicle is moving. The
steeri ng wheel will lock causing loss of
c ontrol.
- If you have to leave your vehicle -even
for just a m inute -always remove t he ig
nition key and take it with you. This is es
pecially important if you a re going to
leave ch ildren behind in the vehicle. The
children co uld start the engine or use
other vehicle controls. Unsupervised use
of vehicle controls (for examp le, power
windows) can cause serious personal in
jur ies .
(!) Tips
If the vehicle battery has been disconnect
ed and then reconnected, then you must
l eave the key in position
(D for about 5
seconds before you can start the engine.
Starting and stopping
the engine
Starting the engine
The engine can only be started with an origi
nal Audi key.
.,. Set the park ing brake.
.,. Move the se lector lever to the neutral posi
tion (automatic transmission): selector lever
in
P or N) ¢ .&_ .
.,. On vehicles with manua l transmission, fully
depress the clutch pedal.
.,. Turn the ignition key to pos it ion @
¢ page 71, fig . 71 -do not depress the gas
pedal when starting the engine!
.,. Let go of the key as soon as the engine
starts.
A cold engine may at first be loud after it has
been sta rted. This is due to the hydrau lic
valves bu ild ing up the oil pressure. This nor
mal and no need for co nce rn .
If the engine does not start immediately, stop
trying after 10 seconds and then try to restart
the engine abou t 30 seconds late r.
A WARNING
Neve r star t or let the eng ine run in a con
f ined or enclosed area . Exhaust fumes
from the engine contain carbon monoxide,
a colorless and odor less gas . Ca rbon mon
oxide can be fatal if inhaled.
- Never leave the engine id ling unattend
ed. An unattended veh icle w ith a runn ing
engine poses a danger of personal injury
or theft.
Automatic car wash
The vehicle can be washed in almost any
modern automatic car wash .
The vehicle paint is so durable that the vehicle
can normally be washed without problems in
an automatic car wash. However, the effect on
the paint depends to a large extent on the de
sig n of the fac ility, the filtering of the wash
water, the type of wash and care mater ial , etc.
If the paint has a dull appearance afte r go ing
through the car wash or is scratched, bring
this to the attention of the operator immedi
ately. If necessary, use a different car wash.
Before going through a ca r wash, be s ure to
take the usual precautions such as closing the
windows. Remove antenna if applicable .
If you have installed additional accessories on
the vehicle -such as spoilers, e tc. -it is best to
ask the car wash operator i f these should be
removed .
A WARNING
Always read and heed all WARNINGS and
the information ¢
page 164.
(D Note
- Fold the exterior mirrors -flat the re is a
risk of damaging the exterio r mirrors .
Power folding exterior mi rrors must not
be fo lded in or out by hand. Use the pow
er function!
- Compare the track of your vehicle w ith
the d istance between the guide ra ils of
the facility- there is a risk of damage to
the wheels and tires .
- Compare the width of your vehicle wit h
the width of the tu nnel at the fac ility.
Washing the vehicle by hand
A lot of water is needed when washing a vehi
cle by hand.
~ Befo re you start washing, make sure you
have read and understood the WARNINGS
¢ A in General informa tion on page 164 .
Cleaning and protec tion 165
~ First soak all dried d irt unt il it is soft, then
rinse it off.
~ As you clean yo ur vehicle, start w it h the
roof and work your way down to the bottom,
using a sponge, a sponge g love or a clean
brush .
~ Rinse the sponge o r the sponge glove often,
flushi ng it clean each time.
~ Use spec ia l car shampoo only fo r very per
sisten t dirt.
~ Rinse the car thoroughly wit h water.
~ Use a chamois leather to gent ly wipe the ex -
terior dry .
U se a separate sponge for cleaning the
whee ls, door s ills and other regions exposed
to road dirt. In this way, yo u wi ll not scratch
the paint wit h coarse particles imbedded in
the sponge the next time you wash the car.
A WARNING
- Wash your vehicle only when the ignition
is switched off to reduce the risk of a
crash .
- Always read and heed all WARNINGS and
other information ¢
page 164.
(D Note
-Never try to remove dirt, mud or dust if
the surface of the veh icle is dry. Never
use a dry cloth or sponge, s ince this
cou ld scratch your vehicle's paint or win
dows .
- Never wash your car in bright sun light.
Drops of wate r act as mag nifying lenses
and may damage yo ur paint .
- Whe n you wash your car in the winter: if
you rinse yo ur vehicle with a hose, be
c ar efu l not to aim the stream of water
directly at locks, or at doo r or hatch
openi ngs -they can free ze sh ut.
- Never use sponges designed to
remove
insec ts, or any k itche n sco uring sponges
or s imil ar p rod ucts. They can damage
your paint finish .
- Never use a dry cloth or sponge to clean
the headlights . Only use wet cloths o r
•
•
This reduces energy consumption and main
tains starting capability over a longer period
c::>
page 156. Some of the convenience func
tions may not operate, such as the interior
lights or power seat adjustment. The conven
ience functions will be ava ilable again when
you switch on the ignition and start the en
g ine .
Winte r oper ati on
During the winter months, battery capacity
tends to decrease as temperatures drop. This
i s because more power is also consumed while
start ing, and the headlights, rear window de
fogger, etc., are used more often .
Avoid unnecessary power consumption, par
ticularly in city traffic or when traveling only
short distances . Let your authorized Audi
dealer check the capac ity of the vehicle bat
tery before winte r sets inc::>
page 193. A we ll
charged ba tte ry w ill no t only prevent starting
prob lems when the weathe r is cold, but will
a lso last longer .
Replacing battery
The new battery must have the same capaci
ty, vo ltage ( 12 volts), amperage, cons truction
and p lug sealing, as the origina l ba tte ry. Spec
if ications are listed on the batte ry housing.
Batteries specially developed by A udi fulfill
the maintenance, output, and safety require
ments.
When insta lling the battery, make sure the ig
nition and all electrica l cons umers are switch
ed off c::>
(i).
We recommen d that yo u use ma intenance
free or
cy cle- re sis tant /leak-pr oof batteries
according to the standards TL 825 06 (from
April 2008) and VW 7 SO 73 (from Apri l
2010).
Replacing the batte ry should be carried by a
q ua lified workshop. P lease follow the instruc
tions on the battery cover.
Checkin g and fillin g 191
@ Note
-All work on the battery requires techni
cal know ledge. Please contact an Audi
dealership or another authorized fac ility
for questions about the battery - danger
of ac id burns and exp losion hazard!
- The battery must not be opened! Do not
try to change the battery 's liquid level,
otherwise detonating gas will escape
from the battery - explosion hazard!
- The AGM battery in the luggage com
partment cannot leak, because the elec
t ro lyte for this batte ry is abso rbed into a
special glass mat. This lea k-proof battery
must not be replace with a convent iona l
bat tery.
- Make su re the ventilation hose on t he
side of the ba ttery is connected, othe r
w ise fumes or battery ac id can leak out.
- Batte ry holder and termin als always
have to be sec ured correc tly.
- Before all work on the batte ry follow the
warning s below c::> .&. in Working on the
battery on page
192 .
@ For the sake of the environment
Because of the p rob lem of proper disposal
of a ba ttery, we recommend your author
i zed Audi dealer change the bat tery fo r
you. Batteries contain sulfuric acid and l ead and must always be disposed of prop
erly in comp liance with a ll environmental
regulat ions. Disposing of vehicle batter ies
i mproperly is very dangerous to the envi
ro nment. Make sure that the removed bat
tery cannot overbalance, othe rwise sulfu
r ic acid might escape!
@ Tips
If your vehicle is left standing for several
weeks at extremely low temperatures, the
vehicle battery shou ld be removed and
stored w here it w ill not freeze. This will
p revent it from be ing dam aged and h aving
to be replaced .
•
•
Fuse Location, Instrument Panel left
0
Fig. 166 Fu se ca rrier behin d th e in strum en t pane l end
fa ce, cover re move d
Some of the equipmen t items lis ted a re op
tional or only available on certain model con
f igurations.
N ote th at the foll ow ing table is ac curate at
the t ime of go in g to press and is subje ct to
c hang e. In t he event of d iscr epan cies, the la
b el on the in side of th e cove r alw ay s take s
precedence .
The power sea ts are pro te ct ed by circu it
break ers,
which automatically reset after a
few seconds after the overload has been rem
ed ied .
No. Equipment
1
2
3
Engine relay, fuel tank contro l
unit, A irbag Off light , light
switch (sw itch illumi nation), di -
agnosti c connector
ABS, ASR, ESC, brake light switch
AFS headlight (le ft)
Amps
10
5
5
Fu se s and bulb s 229
No.
4
5
Equipment
Oil level sensor (extended main-
tenance interval) (WIV), tire
pressure monitoring system,
switch for Electronic Stabiliza-
tion Control (ESC), AFS head-lights (control unit), A/C system
(pressure sensor), backup light
switch
Automatic headlight range con trol, AFS headlight (right) /
manual headlight range con
trol, halogen headlights
Control unit for CAN data trans-
6 fer (gateway), electromechani cal steering, automatic trans
mission shift gate
7 Acoust
ic Park Assist, automatic
dipping interior rear view mir-
ror, garage door opener, heata
ble windshield washer nozzles,
washer pump, w ind deflector
re lay (Roadster)
--r-HaldeX clutch/Haldex clutch
(TTS)
8
Amps
5
5/10
5
5
5/10
9 Control un it Audi magnetic ride 5
----10 Airbag control unit 5
Mass airflow sensor, crankcase
11 heat ing
Door control unit (central lock-
12 ing driver/passenger)
13 Diagnostic conne ctor
Rain sensor, automatic trans-
14 mission shift gate
15 Roof light (inter ior lighting)
16 A/C system (control unit)
17 Tire pressure monitoring sys
tem (control un it)
--~-18 Not used
19 Not used 5/10
10
10
5
5
10
5
I
I
I
20 -------21 Fuel injectors (gasoline engine) 10
22 Wind deflecto r (Roadster) 30
23 Horn 20
IIJ>,
No. Equipment Amps
11 Feed (brake peda l) 5
-
12 Activated charcoal filter/charge I pressure control valve 10
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authori zed Audi dealer replace burned
out bulbs for you .
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bulb . Th is appl ies especially to the l ight bulbs
in the front of your car which you can only
reac h through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
must be correctly taken apart and then prop
e rly put back together to help p revent break
age of parts and long term damage from wa
ter that can enter housings that have not been properly resealed.
F or your safety, we recommend that you have
your author ized Audi dealer replace any bu lbs
for you, since your dealer has the p roper tools,
the correct b ulbs and the expertise.
Ga s di sc harg e lamp s (Xeno n light s}*:
Due to the high electrical voltage, have the
bulbs replaced by a qualified technician.
Headlights with Xenon light can be identified
by the high voltage sticker.
A WARNING
Contact with high-voltage components of
t he electrical system and improper re
placement of gas discharge (Xenon) head
light bulbs can cause serious personal in
jury and death .
- Xenon bulbs are pressurized and can ex
plode when being changed.
Fu ses and bulb s 231
-Changing Xenon lamps requires the spe
cial tra ining, instructions and equip
ment.
- On ly an authorized Audi dealer or other
qualif ied workshop should change the
bulbs in gas discharge lamps .
A WARNING .,.;
There are parts with sharp edges on the
openings and on the bulb holders that can
cause serious c uts.
- If you are uncertain about what to do,
have the work performed by an a uthor
ized Audi dealer or othe r qualified work
shop. Ser ious personal in ju ry may result
from imprope rly performed work.
(D Tips
- If you must replace the light bulbs your
self, a lways remember that the eng ine
c ompartment of any vehi cle is a hazard
ous area to work in. A lways read and
heed all WARN INGS
~page 174, Engine
compartment ¢&, .
-It is best to ask your authorized Audi
dealer whenever yo u need to change a
bulb .
•
•
-
252 Index
H
Headlig hts . .. .. .. ..... ... .. .. .... .. 42
adaptive light .. .. ..... ... .. .. .... .. 43
defect ive . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Front fog lights .................... 44
Sw itching off ............ .... .... .. 42
Sw itch ing on ....................... 42
Washer system . . . . . . . . . . . . . . . . . . . . . SO
Xenon headlights .......... .... ..... 42
H ead restraints . . . . . . . . . . . . . . . . . . . . . . 94
Ad justing ......................... 94
H eated
exterior mirrors ....... ... .. .. .... .. 4 7
front seats (climate control) . . . . . . . . . . 70
rear window . . . . . . . . . . . . . . . . . . . . . . . 70
H ea ted seats . . . . . . . . . . . . . . . . . . . . . . . . 70
H eated washer jets
W iper and washer system ............ 48
Heating ..... ... .. ..... ... .. .. .... .. 66
H igh beam . . . . . . . . . . . . . . . . . . . . . . 42, 4 4
H igh voltage warn ing label ...... .. .. . 238
Hill Descent Assist .... ... .. .. .. .... .. 83
H ill hold ass ist
Starting on hills ........ .. .. .. .. .. . . 74
H omelink ® universal remote control
H ood
Opening .... .. .. ..... ... .. .. .... .
Release lever
. . . ...... ... .. .. .. ' . .
87
180 180
H orn
. . . . . . . . . . . . . . . . . . . . 8 ...........
H ow are c hild restra int system anchors re
lated to child safety . . . . . . . . . . . . . . . . . 143
H ow many airbags does my vehicle have? 115
H ow often shou ld I check my t ire pres-
sures? .. .. ............... .. .. .. .. . 203
H ow safety belt pretensioners work .... 106
Hydroplaning . .. . ...... ... .. .. .... . 207
I
Ignition key . . . . . . . . . . . . . . . . . . . . . . . . . 71
Ignition key safety lock . . . . . . . . . . . . . . . 72
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . 71
I gnition lock pos itions . . . . . . . . . . . . . . . . 7 1
Immobilizer .............. .. .. ...... 12
I mpor tant things to do before driving . . . 90
Imp roperly worn safety belts ...... .... 106 Ind
icator light
Airbag system ... .. ... ..... ... .. .. 119
Audi magnet ic r ide . .. .. ..... ... .. .. . 21
Clutch overheat ing ............. ..... 8S
PASSENGER AIR BAG OFF ........... 119
Ind icator lights
Red symbols in the center display . . . . . . 13
Ye llow symbo ls in the center display . .. 13
also refer to Warning/ind icator lights . . 12
Infan t seats .. ................. .. .. 135
Installing child safety seats
Safety belts . . . . . . . . . . . . . . . . . . . . . . 140
Installing the upper tether strap on the
anchorage .. ................... .... 148
Instrument clus ter and con trols ... .. .. . 10
Instr ument panel illumination .. .. .. .. . 46
Instruments and controls General illustration . . . . . . . . . . . . . . . . . . 8
Interior lights ..... ............. ..... 45
Luggage compartment .... ... .. .. .. . 46
Interlock switch . . . . . . . . . . . . . . . . . . . . . 17
J
Jump-starting
232
Jumper cables ..... ... .. ..... .... . .. 233
K
Key ................................ 32
Battery replacement . . . . . . . . . . . . . . . . 33
Check light .... .. ... .. ..... ... .. .. . 32
Convenience opening and closing of win-
dows . .... .... .. ................. . 40
Emergency key ... ............. ..... 32
Key replacement . . . . . . . . . . . . . . . . . . . 32
Master key . . . . . . . . . . . . . . . . . . . . . . . . 32
Valet key . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Keyless entry remote control ........... 33
Ki ck-down · · .. .. .. ............. .. ... 85
Knee a irbags .. .. .. .. ... ....... ... .. 123
D .. escrrpt1on .. .. ............ ....... 123
How they work . .... .............. . 125
Important sa fety instru ctions ........ 125
L
Lap timer ....... ............ ........ 29