2013 AUDI RS5 CABRIOLET towing

Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently
largecross section to carry the starter current
safely. Refer to the manufacturer's specifica­
tions.
Use only jumper cables with
insulated termi­
nal clamps which are distinctly marked:
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
Emergency situations 255
-A discharged battery can freeze at tem­
peratures just below 32 °F (0 °C). Before
connecting a jumper cable, you must
thaw the frozen battery completely, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to
start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with
a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery. Use of batteries of different voltage
or substantially different "Ah" rating
may cause an explosion and personal in­
jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The ca pa city (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
page 200, Engine com­
partment.
(D Note
- Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc .
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,. •
•

-Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment.
- Do not bend over the batteries - danger
of chemical burns!
- The battery ce ll locking screws must be
t ightened securely .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 200, Engine com­
partment .
(D Note
Improper hook -up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that a ll screw plugs on the battery
cells are screwed in firmly. If not, tighten plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
nect ing a jumper cable as described
above applies spec ifically to the case of
you r vehicle be ing jump started . When
you are giving a jump start to anothe r ve­
hicle, do
not connec t the negat ive( -) ca­
ble to the negat ive( -) term inal on the
discharged battery@¢
fig. 205. In ­
stead, securely connect the negative(-)
cable to e ither a solid metal component
that is firmly bolted to the engine block
or to the engine block itse lf. If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and exp lode!
Em erg en cy si tuation s 257
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow t ruck operators who know
how to operate their equipment safely.
- Never t ow your Audi , tow ing will c aus e
damage to the engine a nd transmi ssion.
- Never wrap th e safet y chain s or winch c a­
ble s around th e brak e lin es.
- To prevent unne ce ss ary dam age, your Aud i
mu st be t ran spo rted with a flat bed truck .
- To load th e vehi cle on to the fl at bed, us e
the t owing loop found in the vehicle t ool s
and atta ch to the front or rear anch o rage
r=:> page 258 and ¢page 258 .
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle being towed, for any reason.
-
•
•

258 Emergency situations
Front towing loop
Do not install the front towing loop until it is
needed.
Fig. 206 Front bumper: removing th e cove r cap
Fig. 207 Fron t bumper: screw ing in t he tow ing loop
The towing loop fits into the threaded hole lo­
cated on the right side of the front bumper
and covered by a small cover when not in use.
... Remove the towing loop from the vehicle
toolkit
c::> page 243.
... Take hold of the bottom edge of the cover
cap and pull it out of the bumper
c::> fig. 206.
... Screw the towing loop tight ly into the
threaded hole as far as it will go
c::> fig. 207.
When it is no longer needed, unscrew the
towing loop and put it back into the vehicle
toolkit . Be sure to have the towing loop stored
in the vehicle at all times.
A WARNING
If the towing loop is not screwed in as far
as it w ill go, the thread can pull out when
the vehicle is towed -potential risk of an
accident .
Rear towing loop
Do not install the rear towing loop until it is
needed .
Fig. 208 Rear bumper: Screw ing in towing loop
On the right sid e of the rear bumper there is a
threaded hole for the towing loop . The
threaded hole is protected by a cover .
... Remove the towing loop from the vehicle
toolkit
c::> page 243 .
... Press the cover in by applying short strong
pressure to the bottom part to release it
from the bumper
c::> fig. 208 .
... Screw the tow ing loop tightly into the
threaded hole as far as it will go.
Unscrew the towing loop again after use and
install the cover in the bumper. Install the
cover in the bumper. Return the towing loop
to the toolkit . Be sure to have the towing loop
stored in the vehicle at all times .
A WARNING
If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potential r isk of an
accident.

264 Consumer Information
Consumer Information
Warranty coverages
You r Audi i s covered by the following war­
ranties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regu lations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A . and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lowe r octane
rating. Improper fuel may cause engine
damage ;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment ;
- replacement pa rts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessar ily work
in Europe, and may not work in other coun­
tries outside of North America.
(D Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, service or parts availability.
Audi Service Repair Manuals and Literature
Audi Official Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduction. Service manuals and lit­
erature are available to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
s afety, economy and rel iability. For detailed
vehicle maintenance consult your Warranty &
Maintenance booklet.
Under difficult operating conditions, for ex­
ample at extremely low outside temperatures,
i n very dusty regions , when towing a trailer
very frequently, etc., some service work
should be performed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
(® For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus minimizing adverse
effects on the environment.
Important considerations for you and
your vehicle
The increasing use of electronics, sophisticat­
ed fuel injection and emission contro l sys-
tems, and the genera lly increasing technical
liJJ,

272 Index
Data recorder ..... ..... ... .. .. .... . 176
Date display . .............. ... .. ... . 12
Daytime running lights. . . . . . . . . . . . 52, 53
Declaration of compl iance
Adaptive cruise control . ... .. ... ... . 267
Audi side assist .. ..... ... .. .. .... . 267
Ce ll phone package .. ... .. .. ... ... . 267
Convenience key ..... ..... .... .... . 267
Electronic immobili zer ..... .. .. .. .. . 267
H omelink ® universal remo te control . . 267
Remote control key ........... .. .. . 267
Defective light bulb warning . . . . . . . . . . . 2 1
Defrosting (w indows) ..... .. .. .. .. .. .. 71
Determin ing correct load limit . .. .. ... 230
D igita l clock ............. ... .. .... .. 12
Dig ita l compass ............ ... .. .. .. 59
Dimensions .. ............... .. .... . 262
D imm ing the rea rview mir ro r .. .. .. .. . . 56
Doors emergency lock ing . ..... .. .. .. .. .. .. 36
Driver information system Eng ine oil temperature indicator ...... 28
Open door or front lid warning . . . . . . . . 24
Outside temperature display .. .... .. .. 24
Sound system display . . . . . . . . . . . . . . . 24
Driver seat
refer to Seat ing pos ition . . . . . . . . . . . . 119
Driving safely ............. .. .. .. .. . 118
Driving through water . . . . . . . . . . . . . . . 184
Driving time . . . . . . . . . . . . . . . . . . . . . . . . 25
Dust filter
refer to Po llutant filte r (automatic AC
sys tem) .. .. ............. .. .. .... .. 69
Dynamic steering . . . . . . . . . . . . . . 104 , 180
E
Easy entry function ......... .. .. .. .. .. 63
Electro -mechanical power assist . . . . . . . 180
Electromechanical park ing brake
E me rgency braking ....... .. .. .. .. . . 81
I ndicator ligh t . . . . . . . . . . . . . . . . . . . . . 79
Par king .. .. .. . .......... .. .. .. .. .. 80
Releasing and clos ing ... .. .. .... .. . . 79
Starting assist . .. ..... ... .. .. .... .. 80
Starting from rest ..... ... .. .. .... .. 80
Warn ing/ indicator lights ..... .. .... .. 16 El
ectronic differential lock ( EDL) . . . . . . . 176
Warning/indicator lights ..... ... .. .. . 19
El ectronic immob ilizer . . . . . . . . . . . . 12, 3 7
Electronic power control (EPC) warning/indicator light . . . . . . . . . 20
E lectronic Stabilization Contro l (ESC) . .. 176
Warning/indicator lights ..... ... .. .. . 19
E mergen cy actua tion
Doors .. .. .. .. .. .. ........... .. .. . 36
Ignit ion key ..... ... .. ..... .... . .. . 34
Emergency brak ing .... .. .. ... ..... .. . 81
Emergency flasher . . . . . . . . . . . . . . . . . . . 54
Warning/ind icator lights ........ .. .. . 22
E mergency key . . . . . . . . . . . . . . . . . . . . . . 32
Starting engine . ... ... ..... ... .. .. . 76
Emergency operation Emergency bra king funct ion (pa rking
brake) .. .. .. .. .. .. ... ........ .. .. . 81
Luggage compartment lid . . . . . . . . . . . . 38
Power top ..... .. .. ... ..... ... .. .. . 47
Emergency starting ................ . 255
Emergency towing . ............. .... 257
E nergy management ............ .. .. 182
Battery power . . . . . . . . . . . . . . . . . . . . . 17
Drive r notif ication . . . . . . . . . . . . . . . . . . 17
Engine Compartment .. .. ... .......... .. .. 209
Coolant . .. .. .. .. ............. .. .. 214
Hood . .... .... ................... 207
Starting . . . . . . . . . . . . . . . . . . . . . . 7 4 , 77
Starting with jumper cables ... .. .. .. 255
Stopping . . . . . . . . . . . . . . . . . . . . . . 76, 78
E ngine compartment
Sa fety instr uctions ............. .... 207
Working the eng ine compartment 207
Engine coolant In dicator light ... ............. .... . 18
Engine coolant system ........... .... 214
Adding coolant ..... ... ..... ... .. .. 214
Checking coolant level .............. 214
Checking the engine coo lant level . .. .. 214
Radiator fan . .. .. ............. .. .. 216
Engine coolant temperature Temperature gauge .............. .. . 10
Engine data ..... .. .. ... ..... ... .. .. 263