2013 AUDI Q5 change wheel

When the malfunction indicator is illuminat­
ed, the system may not be able to detect or
signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of rea­
sons, including the installation of replace­
ment or alternate tires or whee ls on the veh i­
cle that prevent the TPMS from funct io ni ng
p roperly . Always check the T PMS malfunct ion
tellta le afte r replacing one or more t ires or
wheels on your veh icle to ensure that the re­
p lacement or a lternate tires and wheels allow
the TPMS to continue to function properly .
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 208 Display : underinflatio n warning
Using the ABS sensors, the tire pressure moni­
toring system compares the t ire tread circum­
ference and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or mo re tires, th is is indica ted in the instru­
ment clus ter with a
IE warning symbol and a
message ¢
fig. 208. The driver message in the
display goes out after 5 seconds. The driver message can be displayed again by pressing
the
! SET ! button. If only one tire is affected,
the display will indicate its pos ition.
The ti re press ure monitoring system must be
reset via radio or MMI* each time the pres­
sures are adjusted (e.g . when switching be ­
tween partia l and full load pressure) or after
changing or replacing a t ire on your vehicle
¢
page 268 . The TPMS indicator only moni­
tors the tire pressure that you have prev iously
Tire s an d wheel s 267
stored . You can find the recommended t ire
pressures for yo ur vehicle on the label on driv­
er's side B-pillar ¢
page 252.
Tire tread circum ference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire p ress ure in one or more tires is too
low,
- t he t ire has structural damage,
- the t ire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
¢ page 268.
Warning symbo ls
IE Loss of pressure in at least one tire¢.&,.
Check the tire or tires and replace or repa ir if
necessary. The
IE indicato r light in the inst ru­
ment cluster a lso illuminates
c::!;> page 14.
Check/correct the press ures of all fou r tires
and reset TPMS via radio o r MMI*.
119;~, (T ir e Pressure Mon itoring System) Tire
pre ssure: Syst em malfun ction!.
If 11Nlf:1 appears afte r switching the ignition
on or while driving and the
IE indicator light
i n the instrument cluster blinks fo r approx i­
mately one minute and then stays on, there is
a system malf unct ion.
Attempt to store the correct tire pressure
¢ page 268 . If the ind icator light does not
tu rn off o r if it turns on sho rtly the reafter, im­
med iate ly dr ive your vehicle to a n author ized
Audi dealer or au thorized repair faci lity to
have the malfunc tion corrected .
A WARNING
-=
-If the tire pressure indicator appears in
the instrument cluster display, one or
more of your t ires is significant ly under­
inflated. Reduce your speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures. In­
flate the tire p ressure to the prope r pres­
sure as indica ted on the vehicle's tire
pressu re labe l
¢page 252. Driving on a
significantly under-i nflated tire causes
•
•

268 Tires and wheels
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­ paved roads), the pressure monitor indi­
cator may be delayed.
-Ask your authorized Audi dealer if run­ flat tires may be used on your vehicle.
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your vehicle or accidents
could also result.
@ Tips
- The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using tires with the "AO" or "RO" identification on the
tire sidewall¢
page 259. We recom­
mend using these tires.
Reset tire pressure monitoring system
Applies to vehicles: with tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
radio or MMI*.
11> Befo re resetting the TPMS, the current pres­
sures of all four tires must correspond to
the specified values. Adjust the tire pressure
and reset the pressure in the tire pressure
monitoring system according to the load
you are carry ing
¢page 252.
11> Turn on the ignition.
11> Select: ICARI function button > Tire pres­
sure monitoring
> Store now . Or
i,. Select: ICARI function button > Car sys­
tems *
control button > Servicing & checks >
Tire pressure monitoring > Store tire pres­
sures.
@ Tips
Do not store the tire pressure if there are
snow chains on the tire.

2 70 What do I do now ?
& WARNING
-The ch ock cannot fulfil its function and
may lose its stab ility if t he "tabs" on the
s u pport plate are not inserted cor rectly
in to the elongat ed ho les i n th e b ase
pla te. If th is happens, the veh icle may
sta rt to move wh ile a wheel is being
change d.
- N ever u se the f old ing chocks if they are
damaged o r if th ey have no t been assem ­
bled correc tly .
Removing bass box
Appl ies to vehicles: wit h bass box
Before the inflatable spare tire" can be taken
out, the bass box mus t be removed.
Fig . 211 Spare w hee l well : Bas s box
Removing bass box
., Lift up the cargo floor using the hand le .
., Sq ueeze the locking ta bs
c:::> fig . 211 © of
the connector .
., Disconnect the connector @and place the
l ead to one side.
., Turn the large screw counter -cloc kwise .
., Carefully remove the bass box .
Installing bass box
., Carefully place the bass box in the wheel.
The inscr ipt io n "FRO NT" on the bass box
must face forward .
., Reconnect the connector that was removed .
., Secure the bass box wi th the large sc rew.
., Fold the cargo floor back down.
Inflatable spare tire
Applies to vehicles: w ith inflatable spare t ire
The inflatable spare tire expands to its full di­
ameter when it is inflated .
Fig . 2 12 In flatable spa re t ire wi th compresso r
Removing inflatable spare tire
., Lift up t he cargo floo r using the handle .
., Remove the dirt t ray .
., Tur n the large screw
c:::>fig. 212 co u nte r­
clockw ise .
., Remove the bass box as required
¢ page 270 .
., Take out the inflatable spa re tire .
., Always store the vehicle tool kit, the jack*
and the rep laced tire in the luggage com ­
pa rtment
¢ page 145.
Stow ing the inflatable spare tire
., Release the air by unscrewing the va lve
stem .
., Screw the valve stem back in afterwards .
., Wait a few hours before p lacing the wheel
in the spare wheel well¢
A-
., Inst all the bass box as required¢ page 270.
., Se cure t he wheel with t he large screw .
., Place the d irt tr ay b ack in .
., Fold t he cargo floor back down.
After using the inflatable spare wheel
T he inflatab le spare tire can be re-used as
lo ng as it is not damaged a nd is not wo rn
down to the t read wear indi ca tors ¢
_A .
When you let the a ir out of the inf latab le
spar e tir e, it does not ass ume its folded shape
again for severa l hours . U nti l then, it cannot
be pla ced ba ck in the spare whee l we ll and
stowed secu re ly.

/! WARNING
-Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators .
- If the inflatable spare tire is more than 6
years old, use it on ly in an emergency
and with extreme ca ution and carefu l
dr iv ing.
- The inflatab le spare tire is intended only
for temporary and short-term use . It
should be replaced as soon as poss ible
with the no rma l wheel and tire.
- The tire pressure value for the inflatable
spare t ire is located on the driver's side
8-p illar
c::> page 252, fig. 204.
- Maximum permiss ible speed is 50 mph
(80 km/h).
- Avoid full-throttle acce lerat ion, heavy
braking, and fast corner ing.
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for severa l hours. Until then, it
cannot be placed back in the spare wheel
well and stowed secu rely.
- Never drive with more than one inflata­
ble spare tire.
- For technical reasons, the use of tire
chains on the inf latable spare tire is not
permitted .
If it is necessary to d rive w it h
t ir e cha ins, the inflatable spare whee l
must be mo unted on the fron t axle in the
event of a fla t in a rea r tire. The new ly
available front wheel must then be in ­
sta lled in place of the rear whee l with
the flat tire. Installing t he tire chain be­
f ore mounting the whee l and tire is rec­
ommended.
- loose items in the passenger compart­
me nt can cause serious personal in jury
dur ing hard braking or in an acc ident.
Never store the inf latable spare tire o r
jack* and tools in the passenge r com­
partment .
CD Note
-The inf latable spare tire has been devel­
oped spec ifically for this vehicle model.
What do I d o now ? 271
It must not be exchanged or used for
ot her vehicle models . Sim ila rly, inflata­
ble t ires from other vehicle models must
not be used.
- Norma l summer or winte r ti res m ust not
be installed on the inf latable tire rim.
Inflating inflatable spare tire
Applies to vehicles: with inflatable spare tire
Fig. 2 13 Lu ggage compartme nt left s ide: comp ressor
.,. Remove the left tr im panel in the luggage
compa rtment.
.,. Open the Velcro strap and
remove the com­
pressor ¢
fig. 213.
.,. Unscrew the valve stem from the spare tire .
.,. Screw the tire f iller hose from the compres­
sor firmly onto the va lve of the spare tire .
.,. Insert the pl ug from the comp ressor into a
socket of th e vehicle ¢
page 75.
.,. Switch t he comp ressor on.
.,. let the compressor r un unti l t h e va lue
specif ied on the ti re press ure la bel is
reached
c::> page 2 52, fig . 204 . Switch the
compressor off after r unning for 12 minutes
at the most -danger of overheating!
A WARNING
The compressor and the tire filler hose can
become extreme ly hot while t hey a re run­
n ing -da nger of b urns!
CD Note
Switch the compressor off after running
for 12 mi nutes at the most -danger of
ove rheating! Allow the compressor to cool
down for a few m inutes befo re you use it
again .

274 What do I do no w?
Special ca re is requ ired if you are repairin g
t he t ire o n a steep incline.
@ Tips
- Do not operate the compressor for more
than 12 minutes continuously, otherwise i t can overheat. Once the compressor has
cooled, you can continue to use it.
- If sealant has spi lled out, let it dry and
then you can remove it by pee ling it away
like a fo il.
- Remember to obtain a new bottle of
sealant from your authorized Audi dealer
after repairing a tire. After this, the func­
tionality of the tire repair set is restored.
- Obey all laws.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
le ve l ground before yo u stop ¢&_ .
.,. All p assengers sho uld
le ave the c ar and
move to a safe location (for instance, behind
the guardrai l)¢
,A .
.,. Engage the parking brake to prevent your
vehicle from ro lling un intentionally¢ &_.
.,. Move
selecto r le ver to pos ition P ¢ ,A .
.,. If you are tow ing a trailer: unhitch the trail­
er from your veh icle.
.,. Block the diagonally opposite wheel with
the fo ld ing chocks or other objects.
.,. Take the
jack * and the inflatab le spare tir e*
out o f the luggage compartmen t
¢page 269.
A WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low these safety precautions:
-
- If you have a flat tire, move a safe d is­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to a lert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly a nd possib ly slipping off the
jack*, always fully set the pa rking brake
a nd b lock the wheel d iagonally opposite
t he wheel be ing c hanged w it h t he fold­
ing chocks or other objec ts. When one
front wheel is lifted off the ground, plac ­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
mov ing.
- Before you change a wheel, be sure t he
ground is level and firm. If necessary,
use a sturdy board under the jack*.
- Always store the vehicle tool kit, the
jack * and the replaced tire in the luggage
compartment¢
page 145.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order.
1. Remove the decorative wheel cover* . For
more details see also ¢
page 2 75, Deco­
rative wheel covers
or¢ page 2 75,
Wheels with wheel bolt caps .
2. Loosen the wheel bolts ¢ page 276 .
3. Locate the prope r mounting point fo r the
jack* and align the jack * below that point
¢ page 276.
4 .
Lift the c ar with t he jack *¢ page 2 76 .
5 . Remove the
wheel with the flat tir e and
then insta ll the
inflatable spare tire*
¢ page 277 .
6. Tighten all whee l bolts lightly.
7.
Lower the vehicle with the jack*.
8. Use the wheel bolt wrench and
firmly
t ighten all wheel bolts¢ page 276.
9. Replace the decorative
whe el cover *.

/! WARNING
Always read and follow all WARNINGS and information
~ .& in Raising the vehicle on
page
277 and ~page 278.
After changing a wheel
A wheel change is not complete without the
doing the following.
• Always store the vehicle too l kit, the jack*
and the repla ced tire in t he l uggage com­
partment ~
page 145.
• As soon as possible, have the tightening
to rques
on all wheel bolts checked with a
torque wrench . The correct tightening tor­
que is 105
ft lb (140 Nm).
• Have the flat tire
re pl ac ed as soon as possi­
ble.
(D Tips
- If you notice that the wheel bolts are
corroded and difficult to t urn wh ile
changing a tir e, they should be replaced
before yo u check the tighten ing torque.
- Drive at reduced speed unt il you have the
t ightening torques checked .
Decorative wheel covers
Applies to vehicles: with decora tive wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 2 16 Ch anging a wheel: Removi ng the wheel cove r
Removing
• Inse rt the hook provided wi th the ve hicle
tool kit in the hole in the h ub.
What do I d o now ? 275
• Pull off the deco rative wheel co ver
~ fig. 216.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts con be un­
screwed.
Fi g. 217 Cha ngi ng a w heel : rem ovi ng the wheel bolt
caps
Removing
• Push the plast ic clip provided with the ve hi­
cle too l ki t over the wheel bo lt cap until it
engages .
• Pull on the
pla sti c clip to remove the cap
r:!) fig. 217.
Refitting
• Place the caps over the whee l bolts and
push them back o n.
T he caps are to protect and keep the whe el
bo lts clea n.

276 What do I do n ow ?
loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais­
ing the vehicle.
F ig. 218 Chang ing a wheel: loosen ing the w hee l bo lts
loosening
.. Install the wheel b olt wrench over the
whee l bolt and push it down as fa r as it wi ll
go .
.. Take tight hold of the
end of the wrench
handle and turn the wheel bolts
counter ­
clockwise
about one single turn in the direc­
t io n ofarrow ¢fig .
218 .
Tightening
.. Install the wheel bolt w rench over the
wheel bolt and push it down as far as it will
go.
.. Take tight hold of the
end of the wrench
hand le and turn each wheel bol t
clockwise
unti l it is seated.
_& WARNING
- Do no t use for ce or hu rry w hen ch angi ng
a whee l - you c an c ause the vehicle to s lip
off the jack* and ca use serious personal
injuries .
-Do no t loosen the whee l bolts more than
one turn
before you ra ise the veh icle with
the jack* . -You risk an i njur y.
(D Tips
If a wheel bo lt is very t ight, you may find i t
e asie r to loosen by ca refully push ing dow n
on t he end of the whee l bolt wrench with
one foot only . As you do so, ho ld on to the ca
r to kee p your ba lance and take care no t
to s lip.
Raising the vehicle
The vehicle must be lifted with the jack * firs t
before the wheel can be removed.
Fig . 2 1 9 Sill pane ls: mark in gs
Fi g. 22 0 Sill: pos it io nin g the jack
.. Engage the parking brake to prevent your
veh icle from rolling unintentionally
.. Move the
select or lever to po sition P.
.. Find the marking (imp rint) on the sill tha t
is nearest t he wheel that w ill be changed
r:::;, fig . 219. Be hind the mar kin g, there is a
lifting point on the sill for the jack *.
.. Turn t he
jack* located under the lifting
point on the sill to ra ise the jack until its
arm @
r:::;, fig. 220 is located under the des­
ig nated p lastic mount
r:::;, ,& ¢ 0.
.. Align the jac k* so t hat its arm @ r:::;, fig. 220
engage s in the desig nated lifting poin t in
t he doo r sill and the movable base ® lies
flat on the ground. The base ® must be
ver­
tical
un der the lifting point @.
.. Win d the jack * up further until the flat tire
comes off the ground
Q ,& .
Position the jack* only under the designated
li fting points on the s ill
r:::;,fig. 219. There is Ill-

278 What do I do no w?
• Use the hexagonal socket in the screwdriver
hand le to screw in and tighten all wheel
bolts
slightly .
• Remove the alignment pin and insert and
t ighten the remaining wheel bolt slightly
Like the rest .
• Turn the jack handle* counter-clockwise to
lower the vehicle unt il the jack* is fully re­
leased .
• Use the whee l bolt wrench to t ighten al l
wheel bolts firmly¢
page 2 76. Tighten
them
crosswise, from one bolt to the (ap­
proximate ly) opposite one, to keep the
whee l centered.
@ Note
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
@ Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bolts .
- Pull the reversible b lade from the screw­
driver before you use the hexagonal
socket in the handle to turn the whee l
bo lts.
- When mounting tires with
un id irectional
t re ad desi gn
make sure the tread pat­
tern is pointed the right way
~ page 278.
- The wheel bolts should be clean and easy
to turn . Check for d irt and corrosion on
the mat ing surfaces of both the whee l
and the hub. Remove all dirt from these
s ur faces before remo unt ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tre ad pattern
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection , please
note the following :
- The direct ion of rotation is marked by an ar­
row on the side of the ti re .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optimum performance cha racter­
isti cs wit h regard to aquap lan ing, no ise and
wear .
- We recommend that you pay part icu la r at­
t ention to th is fact d uring wet wea ther and
t ha t you adjust you r speed to match road
conditions .
- Replace the fl at tir e with a new one and
have it insta lled on you r vehicle as soon as
possible to restore the handling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information¢ page 259, New
tires and replacing tires and wheels
if you a re
going to use a spare tire which is different
from the ti res on your vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after install ation.
- Have th e whe el bolt tight ening torqu e
c hecked with a torque wrench as soon a s
pos sible by your author ized Audi de aler or
a q ualified wo rkshop.
- With steel and alloy wheel r im s, the wheel
bolt s are cor re ctl y tightened at a torque of
105 ft lb (140 Nm).
- If you noti ce th at the wheel bolts are cor­
roded and diffi cult to turn while changing
a ti re , they should be repl aced before you
check the t ightening torque. .,..