2013 AUDI A7 ignition

Automatic headlights
You can adjust the following settings in the
Automatic headlights menu:
Headlights activation time -You can adjust if
the headlights switch on
Early, Med . or Late
according to the sensitivity of the ligh t sensor.
Audi adaptive light* -You can switch adaptive
light
On and Off.
Daytime running lights
USA models:
You can switch the dayt ime run­
n ing lights
on and off .
Canada models :
The function cannot be
turned off . It is activated automatically each
time the ignition is switched on. This menu
item is shown "greyed out" .
Coming home, Leaving home
The coming home function illuminates the
area outside the vehicle when you switch the
ignition off and open the driver's door. To turn
the function on, select
Lights when leaving
car > On .
The leaving home function illuminates the
area outside the vehicle when you un lock the
vehicle. To turn the funct ion on, select
Lights
when unlocking car > On .
The coming home and leaving home functions
only operate when it is dark and the light
switch is in the
AUTO position. Clear
vision 45
Turn signals and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as
the headlight flash­
er.
Fig. 35 Tu rn signal and high beam lever
The turn signal and high beam lever has the
following functions:
Turn signals ¢ 9 ©@
.. 0 .... ~
.,. Push the leve r up as far as it can go to turn
on the right turn signa l or down to turn on
the left tu rn s ignal ¢
fig. 35.
... Move the lever briefly until you meet resist­
ance and re lease it to flash three times.
.,. Move the lever (up or down) until you meet
resistance and hold it there to determine
the flashing time for the turn signals.
High beam ~D @
... Push the lever forward to switch on the high
beam .
.,. Pull the lever back towards you to sw itch
off
the high beam.
Headlight flasher ~D ©
... Pull the lever toward the steering wheel to
use the headlight flasher.
Notes on these features
-The turn signals on ly work w ith the ignition
sw itched on. The indicator l ights
B or Bin
the instrument cluster¢ page 12 also blink.
-After you have turned a corner, the turn sig-
n al switches
off automatically.
- The
high beam works only when the head-
lights are on. The indicator light
El in the .,.

46 Clear vis ion
instrument cluste r illuminates when the
high beams are on.
- T he
headlight flash er works only as long as
yo u hold the lever - even if there are no
l ights turned on. The indicator light
II in
the instrument cluster il luminates when you
use the headlight flasher.
A WARNING
Do not use the high beam or headlight
flasher if you know that these could blind
oncoming traffic.
Interior lights
Front and rear interior lighting
Fi g. 36 Headliner: Front interior ligh ts
Fig . 37 Re ar headli ne r: Readi ng light
Press the appropriate button q fig . 36:
El-Interior lighting on/off
I]]-Door contac t sw itch . The inter ior lighting
turns on automatica lly when you unlock the
vehicle, open a door or switch the ignition off.
The interior lighting turns off several seconds
after you close the doors, when you lock the
vehicle or when you sw itch the ignition on.
When a door is open, the light t urns off afte r
a few minutes.
L:!l -Read ing lights on/off
~ - Switching the rear read ing lights on/off
from the cockpi t.
I" REARI * - Switching the rear reading lights
o n/off from the cockpit.
Ambience lighting
Applies to vehicles: with ambience lighting
You can adjust the br ightness for the ambi­
ence ligh tin g.
.. Select in the MMI: ICARlfunction butto n>
(Car )* sys tem s control button > Vehicle set­
ting s
> Interi or lighting > Brightne ss.
.. To increase or reduce the b rightness , turn
t he knob and press it .
T he ambience light ing tu rns on when you turn
t h e headlights on wh ile the ig nition is swi tc h ­
ed on.
(D Tips
The setti ng is automati cally sto red and as­
s igned to the remo te contr ol key t hat i s in
u se .
Instrument illumination
You can adjust the brightness of the instru­
men t and di splay illumination a s well as the
Head-up Display*.
Fi g. 38 Instrume nt illumina tion
... Press the knob to re lease it.
.. Turn the knob toward"-" or"+" to reduce or
increase the br ightness .
.. Press the knob aga in to return it to its origi-
na l posit ion . ...

48 Clear vis ion
© -Single wipe . If you hold the lever in this
position longer, the wipers switch from slow
wiping to fast wip ing.
® -Clean the windshield . T he wipers wipe
one time after several seconds o f driv ing to
remove water drop lets . You can switch this
function off by moving the lever to position ®
within 10 seconds after the afterw ipe. The af­
terw ipe funct ion is react ivated the next time
you switch the ig nition on .
C leaning the headlights *. The headlight wash­
er system* operates on ly when the headlights
are on. If you move the lever to pos ition ®,
the head lights and the nig ht vision assistant
camera* are washed in intervals .
A WARNING
- The ra in sensor is only des igned to assist
and support the drive r.
It remains entire­
ly the dr iver's respons ibility to monito r
o utside wea ther conditions and to man­
ually activate the wipers as soon as rain
or drizzle reduces visib ility through the
windshield.
- The windshie ld must not be treated with
water-repe llent materials. They can in­
crease glare under poor visib ility condi­
t ions such as wetness, darkness, or when
the sun is low on the horizon. In addi­
t io n, they can cause the wi ndshield wip­
ers to chatter .
- Properly fu nctioning windshie ld w iper
blades are required fo r a clear view and
safe dr iv ing
c::> page 48, Replacing
windshield wiper blades .
(D Note
- In the case of frost, check whether the
winds hield wiper b lades a re frozen to
the windshie ld. Switching on the wind­
s h ield wipers can damage the wipe r
blades!
- Prior to using a car wash, the windshield
wipe r system must be switched off (lever
i n position @). This helps to prevent un­
i ntent ional sw itching on and damage to
the windshie ld w iper system. - Do not
use the w ipers to clear a frosted
w indow . Us ing the wipers as a conven­
ient ice scrape r will destroy the wiper
blades.
(D Tips
- The windshie ld w ipers are switched off
w hen the ignit ion is off. Activate the
w indshield wipers after the ign ition is
switched back on by moving the w ind­
shield wiper lever to any position .
- Worn or d irty windshield wiper blades
result in streaking. This can affect the
rain sensor function . Check your wind­
shield wiper blades regularly.
- The washer fluid nozz les of the wind­
shield washe r system a re heated at low
tempe rat ures when the ignition is on .
- Whe n stopping temporarily, e.g . at a
traffic light, the set speed of the wind­
shield w ipe rs is automatically reduced by
one speed.
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear .
Fig. 42 Remov ing w indsh ie ld wiper b lades
Service position
.,. Switch the windsh ie ld w ipers o ff (position
@ c::>fig. 41).
.,. Switch the ignition off and move t he wind ­
shie ld w iper lever to position ©
c::> fig. 41.
Or
.,. Select in the MMI: ICAR I function bu tton >
(Car) * system s control b utton > Servicing &
check s > Wiper service position > On . The ..,.

windshield wipers move into the service
position .
Removing the wiper blade
• Fold the windshield wipe r arm away from
the windshie ld.
• Press the locking knob@<>
fig. 42 on the
wiper blade . Hold the wiper blade f irm ly .
• Remove the wiper blade in the direction of
the arrow.
Installing the wiper blade
• Inse rt the new wiper b lade into the mo unt
on the w iper arm @ until you hear it latch
into place .
• Place the w ipe r arm back on the windshie ld .
• Switch the ignition on .
• Press the w indshield wiper lever.
Or • Select :
ICAR I function button > (Car )* s ys­
tems
control button > Se rvic ing & checks >
Wiper service position > Off .
A WARNING
- If the windshield wipe rs smear the wind­
shield, clean the w iper blades with w ind­
shield washe r fl uid . If the wiper blades
are extremely d irty, yo u can also clean
th em with a soft sponge or cloth.
- For yo ur safety, you should repla ce the
w ipe r blades o nce or twice a year. See
yo ur a uthori zed Au di dealer fo r repl ace­
me nt blades.
(D Note
- The w indshield wiper blades must on ly
b e fo lded away when in the se rv ice po si­
tion! Otherw ise, you risk d amaging the
p ain t on the hood or the windshield wip ­
er motor.
- You s hould not move yo ur vehicle or
press the windshie ld wiper lever when
the wiper arms are folded away from the
windsh ield. The w indshield w ipers would
move back into the ir original position
and could damage the hood and w ind­
s h ield .
Clear vi sion 49
- T o help p revent damage to the wiper sys ­
tem, always loosen blades wh ich are fro­
zen to the winds hield before operating
wipers.
- To hel p pr event damage to wiper b lades,
do not use gaso line, kerosene , paint
thinner, or other solvents on or near the
wiper blades.
- To help prevent damage to the w iper
arms or other components, do not at­
tempt to move t he wipers by hand .
(D Tips
-Commercial hot waxes app lied by a uto­
matic car washes affect the cleanability
of the windshie ld.
- You can also use the service position, for
example, if you want to p rotect the
w indshield from icing by using a cover .
- You cannot activate the serv ice position
when the hood is ope n.
Mirrors
Adjusting the exterior mirrors
Fi g. 43 Fo rward sect io n of d river' s armr est: power mir·
ro r controls
Turn the knob to t he desired positio n:
Q/P -In this pos ition, yo u can adjust t he
driver's an d fro nt passenge r's exte rior mi rrors
by turning the knob i n the desired d irection.
Qiil -The mirrors are heated depending on the
outside tempe rature .
8 -The exterior mirrors fold in . In the MMI,
you can select if the mir ro rs fo ld in automati-
ca lly when you lock t he veh icle <>
page 35. ~

50 Clear vis ion
Tilt function for the pass enger' s mirror
To help y ou see the curb when backi ng into a
parking space , the surface of the m irro r tilts
slightly. The knob must be in the P position
for this to happ en .
You can adj ust the ti lted mirror s urface by
turning the knob in the desired direction .
When you move out of reverse and into anoth­
er gear, the new mirror position is stored and
assigned to the key you are using.
The mirror goes back into its origina l positio n
once yo u drive forward faster than 9 mph (15
km/h) or sw itch the ignition off .
A WARNING
- Curved (i.e . convex) mirror s urfaces in­
crease your field of view. Remember that
vehicles or other objects will appear
smaller and fa rther away than when seen
in a flat mi rror .
If you use this mirror to
est imate distances of following vehicles
when ch anging lanes , you cou ld es tim ate
incorrectly and cause an acc ident .
(D Note
-If the mirror hous ing is moved uninten­
tiona lly (for example, whi le par king you r
vehicle), then you must first fo ld the mi r­
r or electr ically. Do not readjust the mir ­
ror housing manua lly. You could damage
t h e motor which controls the mirror.
- If you wash t he vehi cle in an au tomatic
car wash, yo u m ust fold the exterior m ir­
ro rs in to reduce the risk of damage to
the mirrors. Never fold power fo lding ex­
terior mirrors* by hand. Only fold them
i n and out us ing the power contro ls.
(D Tips
- The exterior mirror settings are stored
with the memory funct ion*
c> page 56.
- If there is a malfunct ion in the electrical
system, you can still ad just the exter ior
mir rors by press ing the edge of the mir­
r or.
Dimming the mirrors
F ig . 44 A uto ma tic d immin g rearview mirro r*
Manu al anti-glare adjustment
.,. Move the small leve r (located on the bot­
tom edge of the mirror) to the rear.
Automatically dimming mirrors*
.,. To dim the rearview m irror and both exteri­
or m irrors, press the@ button . The diode
@ turns on . The rearview and exterior mir­
rors dim automatically when light shines on
them, for examp le from headlights on ave­
hicle to the rear .
A WARNING
-Electrolyte fluid can lea k from automatic
d imm ing mirro rs if the g lass is broken .
E lectro lyte fluid can irr itate sk in, eyes a nd
r espira to ry system .
- Repeated or prolonged exposu re to e lec­
trolyte can ca u se irritation to the respira­
t ory sys tem, especially among people
wit h asthma or other resp iratory condi­
tions . Get fresh air immediately by leav ­
ing the vehicle or, if that is not possib le,
open w indows and doors all the way .
- If electrolyte gets into the eyes, fl ush
them thorough ly with large amou nts of
clean water for at least 15 minutes; medical attention is recommended.
- If electrolyte contacts skin, fl ush affect­
ed area with clean water for at least 15 minutes a nd then wash affected area
with soap and water; medical atte ntion
is recommended. Thoroughly wash af­
fect ed clothing and shoes before re use .

Front passenger's seat
Always move the front passenger seat into the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted correctly . We recommend that you adjust the
passenger's seat in the following manner:
.. Bring the backrest up to an (almost) upright
pos it ion .
Do not ride with the seat reclined .
.. Adjust the head restra int so the upper edge
i s as even as possib le wit h the top of you r
head.
If that is not possib le, try to adjust
the head restraint so that it is as close to
this position as possible
c::> page 55.
.. Place your feet on the floor in front of the
passenger's seat.
Front seats
Controls
Moving the seat forward or back and adjust­
ing the height, backrest angle and seat an­
gle.
F ig . 45 Fron t seat: adjus ting the sea t
@-Mov ing the seat forward/back: press the
button forward/back
c::> .&, .
@ -Mov ing the sea t up/down: p ress the but­
ton up/down
c::> ,& . To ad just the front sect ion
of the seat, press the front button up/down
c::> .&, . To adjust the rear section of the seat,
press the rear button up/down
c> ,& .
@ -Turn the massage function* on/off. Yo u
can select the type of massage using the mu l­
tifunction button
c> page 54.
S ea ts a nd s to rage 53
© -Backrest forward/back: press the button
forward/back
c::> .&, .
(!)-Lumbar support* : press the button in the
corresponding position
c::> .& or multifunction
button*
c::> .& , c::> page 54 .
A WARNING
-
-Never adjust the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do this while the veh icle is moving,
you will be out of position. A lways adjust
the dr iver's or front passenger's seat
when the vehicle is not moving .
- Be careful when adjusting the seat
he ight. Check to see that no one is in the
way, or ser ious injury cou ld result!
- Because the seats can be e lectrically ad­
justed with the ignition off, never leave
children unattended in the veh icle. Unsu­
perv ised use of the electric sea t ad just­
ments may cause serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas­
sengers mus t never r ide in a moving ve­
hicle with the backrest reclined. Safety
be lts and the airbag system on ly offer
maximum protection when the backrest
is upright and the safety belts are prop­
erly positioned on the body. The more
the backrest is reclined, the greater the risk of personal injury from an incorrect
seating position and imprope rly posi­
tioned safety belts.

70 Warm and cold
l The winds hield and s ide windows are defrost­
ed or cleared o f condensation as quickly as
possib le. The maximum amo unt of air flows
mainly from the vents below the windshield.
Recirculation mode switches off .
The
IAU TOI b utton switches the defroster off.
ICmJ REAR I Switching rear window heater
on /off
The rear w indow heater only operates when
the engine is running . It switches off auto­
matica lly after a few minutes, depending on
the outside temperature.
To prevent the rear w indow heater from
switch ing off automatically, press and hold
the ~ button for more than 2 seconds. This
remains stored unti l the ignition is switched
off.
~ Ad justing s eat h eat ing
Press ing the button switches the seat heat ing
on at the highest setting ( leve l 3) . T he LEDs
indicate the temperature leve l. To reduce the
temperature, press the button again. To
switch the seat heating off, press the button
repeatedly unt il the LED turns off.
After 10 minutes, the seat heating automati ­
cally switches from leve l 3 to level 2.
The seat heating for both outer rear seats* is
ad justed using the buttons in the center con­
sole.
Air vents
You can open or close the center and outer
vents in the cockpit and the vents in the rear center console using the ridged thumbwhee ls.
The levers adj ust the direction of the airflow
from the vents.
T he air temperature in the rear can be ad just­
ed so that it is warmer or co lder by turning
the knob to the red or blue area.
A WARNING
- Do not use the recirc ulation for extended
periods of time. The windows could fog
up since no fresh a ir can enter the vehi­
cle . If the windows fog up, p ress the air
recirc ulation button again immediately
to switch off the air reci rculation func­
tion o r se lect defros t.
- I ndividuals w ith reduced sensitivity to
pa in or temperature cou ld deve lop burns
when using the seat heating fu nction. To
red uce the risk of injury, these indiv idu­
a ls shou ld not use seat heating.
0 Note
To avoid damage to the heat ing elements
i n the seats, do not kneel o n the sea ts or
place heavy loads on a sma ll area of the
seat.

Warm and cold 71
Four-zone automatic climate control
Operation
Applies to vehicles: with four -zone a utomat ic climate control
We recommend pressing the IAUTOI button and setting the temperature to 72 °F (22 °C).
F ig. 73 Four -zone automat ic climate control: controls
Fig. 74 F our -zone automat ic climate control: rear con·
trols
Press the buttons to turn the functions on or
off. Use the dials to adjust the temperature,
the blower speed and the air distribution. The
LED in a button will light up when the func­
tion is switched on. The settings are shown in
the climate control display and are also shown in the MMI display for a few seconds . The driv­
er and front passenger settings can be adjust·
ing separately.
The settings can also be adjusted in the rea r
r::;,fig. 74.
IOFFl Switching the climate control
system on/off
The IOFFI button switches the climate control
system on or off .
It also switches on when you
turn the dial or press any button . Airf low from outside is blocked when the
climate control
system is switched off.
You can activate the residual heat funct ion
when the ignition is off by pressing and hold­
ing the ~ button. The residual heat from the
coolant is used to heat the vehicle interior.
The residua l heat function switches off auto­
matically after about 30 minutes.
IACI Switching cooling mode on /off
T he air is not coo led and humidity is not re­
moved when cooling mode is switched off.
This can cause fog on the windows. Cooling
mode switches off automatically when the
outside temperature is below zero.
1- 1 Switching recirculation mode on/off
In recircu lation mode, the air inside the vehi ­
cle is circ ulated and filtered. This prevents the
unfiltered air outside the vehicle from enter­
ing the vehicle interior. We recommend
switching recirculation mode on when driving
through a tunnel or when sitting in traffic
¢ Li). .
The !AUTO ! button or~ button switches recir-
culation mode off. .,..