2013 AUDI A6 transmission

-Never mount used tires on yo ur vehicle if
yo u are not sure of their "previous histo­
ry." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
- If you notice unusual vibration or if the
vehicle pulls to one side when d riving, al­
ways stop as soon as it is safe to do so
and check the wheels and tires for dam­
age .
(D Note
Please note that summe r and wi nte r tires
are designed for the cond itions that are
Glossary of tire and loading terminology
Accessory weight means the comb ined weight (in excess of
those sta ndard items which may be rep laced)
of au toma tic transmission, power steer ing ,
power brakes, power windows, power seats,
radio, and heater, to the extent that these
items are availab le as factory-installed equip­
ment (whether installed or not) .
Aspect ratio
means the rat io o f the height to the w idth of
the tire in percent . Numbers of 55 or lower in ­
dicate a low sidewall for improved steering re­
sponse and better overa ll handling on dry
pavement .
Bead
means the part of the t ire t hat is made o f
steel wires, wrapped or reinforced by ply cords
and that is shaped to fit the r im.
Bead separation
means a b reakdown of the bond between
components in the bead .
Cord means the strands forming the plies in the
tire.
Tire s an d wheel s 241
typica l in those seasons . Aud i recommends
using winter tires during the winter
months . Low temperatures signif icant ly
dec rease the e lasticity of summer t ires,
which affects tract ion and brak ing ability.
If summer t ires are used i n very co ld tem ­
peratures, cracks ca n form o n the tread
bars , res ulting in perma nen t tire damage
that can cause loud driving noise and un­
bala nced ti re s. Audi i s not respon sible for
th is type of damage .
Cold tire inflation pressure
means the t ire p ress ure recommended by t he
vehicle manufacture r fo r a tire o f a des ignated
s ize t hat has not bee n driven for more than a
coup le o f miles (k ilometers) at low speeds in
the three hour period before the tire press ure
is m easured or adjusted.
Curb weight
me ans the we ight of a motor ve hicle with
st andard equipmen t incl ud ing the max imum
capacity of fuel, oi l, and coolant, air condi ­
tioning and additional weig ht of optiona l
equipment.
Extra load tire
means a t ire design to oper ate a t higher load s
and at higher inflation pressures than the cor­
responding standa rd tire . Extra load tires may
be identified as "XL", "x l", "EXTRA LOAD", o r
"RF" on the sidewal l.
Gross Axle Weight Rating ("GAWR")
me ans the load-ca rry ing capac ity of a single
axle system , measured at the tire -ground in­
te rfaces.
Gross Vehicle Weight Rating ( "GVWR ")
mea ns the maximum total loaded we ight of
the ve hicl e. .,..
•
•

272 Fuses and bulbs
Fuse panel @ (brown)
No. Equ ipment Amps
Climate control 10
Climate control system blower 40
3
D iagnost ic connec tor 10
4 Electrical ignition lock 5
5
Power s teer ing column adju st-
ment
5
6 Steering column switch module 10
7
Power steering column ad just -
ment
25
8 Light switch 5
Luggage compartment fuse assignment
F
ig . 2 13 Lu ggage compar tment: fuse pa nel w ith plas­
t ic bracket
Fu se panel A (black )
No. Equipment Amps
Electromechanical pa rking brake 30
Electraomechanical parking brake 30
6
Front door (front passenge r's
30 s ide)
7 Rear exterior lighting 30
Rea r su n shade, closing aid, lug-
8 gage
comp artment lock, con-
20
venience key, S TA RT E NGIN E
STOP, fuel fi ller door
9 Power seat adjustment 15
1 0
Pa rking system 5
11
Rear seat heating 30
Fuse panel @ (red )
No. Equipment Amps
1 Left belt tensioner 2 5
2 25
3
Socke t 20
4
Socket 20
5
Ele ctrome chanic al p arking b ra ke 5
6 adaptive air suspension 15
7
Rear door (fron t passenger's
30 side)
8 Rear exterior lighting
30
9
L
u ggage compartment lid con-
30 trol mod ule
Telephone
5
11
So und amplif ier 30
12
Rear spoiler (Sportback) 20
Fuse panel © (brown)
No . Equipment Amps
1 Radio receiver, Sound amplifier/ 3 0/ 20
MMI unit/dr ives
Tank lea k detec tion sys tem
5
4 AEM co ntrol module/battery 10/15
mo dule
Battery fan
35
Rad io rec eiver 7,5
7 ,5
9
Automatic dimm ing in terior 5/15
rea rv iew mirror /ba ttery m od ule
10 Parking system 5
Fuse panel @ (green)
No. Equipment Amps
1 Audi pre sense 5
2
Electromechanical parking brake 5
3 ad a pt ive air suspen sio n 5
4
Automatic transmission 7,5
5
Parki ng sys tem 5
6 Rear Seat Entertainment 5
7
Start -Stop-System 5
8 Audi side assist 5

2 7 4 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicles w ith an automatic transmission
cannot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another veh icle,
using a
pair of jumpe r cables to start the en­
g ine .
Jumper cables
Use only jumper cables of sufficiently large
cross section to carry the starter current safe­
ly. Refer to the manufacturer's specif ications.
Use only jumper cables with
insulated termi­
na l clamps which are distinctly marked:
plus(+) cable in most cases colored red
minu s(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
inju ry. Follow the instructions below for
safe handling of your veh icle's battery.
- Always shield you r eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can freeze at tem­
peratures just be low 32 °F (0 °C). Before connecting a
jumper cable, you must
thaw the frozen battery complete ly, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with a low acid level in the battery.
- The vo ltage of the booster battery must
also have a 12-volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of d ifferent voltage
or substantially different "Ah" rating
may cause an exp losion and personal in­
jury.
- Never charge a frozen batte ry. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batter ies of different voltage or
substantially different capacity (Ah) rat­
ing may cause an exp losion and injury.
The capacity (Ah) of the booster battery
should not be lower than that of the dis ­
charged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
¢page 219, Engine com­
partment.
«I) Note
-Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
contro l units, relays, rad io, etc .
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,_

2 76 Emergency situations
-When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the engine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS c:>
page 219, Engine com­
partment.
(D Note
Improper hook-up of jumper cables can ru­
in the generator.
-Always connect POSITIVE(+) to POSI­ TIVE(+), and NEGATIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
necting a jumper cable as described
above applies specifically to the case of
you r vehicle being jump started. When
you are giving a jump start to another ve­
hicle, do
not connect the negative(-) ca­
ble to the negative(-) terminal on the
discharged battery@c:>fig.
215. In­
stead, securely connect the negative(-)
cable to either a solid metal component
that is firmly bolted to the engine block
or to the engine block itself. If the bat­
te ry that is being charged does not vent
to the outside, escaping battery gas
could ignite and explode!
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
tng.
The follow ing information is to be used by
commercia l tow truck operators who know
how to operate their equipment safely.
-Never tow your Audi. Towing will cause
damage to the engine and transmission .
- Never wrap the safety chains or winch ca­
bles around the brake lines.
- To prevent unne cessary damage , your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the flat bed, use
the towing loop found in the vehicle tools
and attach to the front or rear anchorage
c:> page 2 76 and c:> page 2 77.
.&_ WARNING
=
A vehicle being towed is not safe for pas-
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig. 216 Front bumpe r: cove r
Fig. 217 Front bumper: installing the towing loop
-
The towing loop fits into the threaded hole lo ­
cated on the right side of the front bumper
and covered by a sma ll cover when not in use.
.,. Remove the towing loop from the vehicle
tool kit.

heavy components such as the engi ne
b lock or transmiss ion are removed.
- W hen removing heavy components like
these, ancho r vehicle to hoist o r add cor­
respond ing weig hts to ma inta in the cen ­
ter of g ravity . Otherwise, the vehicle
m ight tilt o r sli p off the hoist, causi ng
ser ious p erso na l in ju ry.
([) Note
-Be awa re of the fo llowing points befo re
li fting t he vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame , a rubber pad must be
i nserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the veh icle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.
Emergency situations 2 79
•
•

280 General information
General information
Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::> page 282. This sec­
tion provides general information, notes and restrictions which apply to this data.
Vehicle identification
The key data is given on the vehicle identifica­
tion number (VIN) plate and the vehicle data
sticker .
Fig. 223 Veh icle Ide ntificat io n Number (VlN) p late: lo ­
cation on driver 's s ide das h panel
Fig. 224 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
ble from the outside through the windshield
r:::> fig . 223. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select: Function button
I CAR ! > (Car) *
systems
> VIN number . The
vehicle identification label
is located in the luggage compartment in the
spare wheel well.
The label¢
fig. 224 shows the follow ing vehi­
cle data :
(D Product ion control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is your assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
t ime the vehicle was manufactured . You can
find this sticker on the left door jamb .
It
shows the month and year of production and
the vehicle ident ification number of yo ur vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the bas ic vehicle plus fu ll fuel tank,
oi l and coo lant, plus maximum load, which in­
cludes passenger weight (150 lbs/68 kg per
Ill>

0
Occupant seating positions .... .. .. .. . 12 7
Octane rating .............. ... .. .. . 220
Odometer . .. .... ............. .. .. .. 27
OFF (automa tic climate cont ro l) . . . . . . . . 67
OFF (climate control) .......... ... .. .. 65
Oi l
refer to Engine oil ..... ... .. .. .. .. . 227
On-boa rd compute r ........ .. .. .. .. .. 24
On-Board Diagnostic System (OBD) Data Link Connector (DLC) ............ 29
Electronic speed lim iter . . . . . . . . . . . . . . 30
Malfunct io n I ndicator Lamp (M IL) ..... 29
Open door/hood/rear lid warning . . . . . . . 23
Opening Hood .... .. .. .. .. .. .... ... .. .. ... 225
Power windows . . . . . . . . . . . . . . . . . . . . 38
Sliding/tilting sunroof .. ... .. .. .... .. 40
Opera te you r vehi cle econom ica lly and
m inim ize po llution .................. 201
Other equipment (eff ic iency program) ... 26
Outlet .... .. .. .... .. .... ... .. .. .... 56
p
Paint
Touch-up ... .. .. .. .. .... ... .. .. ... 213
P aint No .... ..... .......... ..... ... 280
Park ing ... .. ............. .... .. .... 75
Automatic transmission ..... .. .. .. . 107
Valet park ing .... .. ... ... .. .. .. .. .. 39
Park ing b rake . .... ..... ... .. .. .. .. .. 74
also refer to Electromechanica l park ing
brake ............................. 74
P ar king system
Ad justing the disp lay/wa rning tone . .. 122
C leaning camera lens ... ... .. .. .. .. . 21 1
C leaning the rear view camera .. .. .. . 1 14
Malfunct ion .. ........... .. .. .. .. . 123
Park ing system plus ................ 113
Periphe ral cameras .............. .. 117
Rear v iew camera .................. 114
Trailer h itch ..... .. ... ... .. .. .. .. . 123
alsorefertoPar kingsystems . .. 113,1 14
Park ing systems .................... 112
P arts rep lacement . ..... ... .. .. .. .. . 28 7
Inde x 297
Pass-through w ith ski sack . . . . . . . . . . . . . 63
PASS ENGER AIR BAG OFF light ........ 158
Passenger protect ion ............ .. .. 190
Passive safe ty system ................ 126
Pedals ........ ... .. ............... 131
Physical principles of a frontal collision . 137
Polishing ....... ................... 212
Pollen filter
refer to Pollutant filter .............. 64
Pollutant filter ...... . .. .. ..... ... .. . 64
Power locki ng syst em ........... .... .. 33
L ocking/unlo ck ing t he veh icle from i n-
s ide .............................. 36
Rea r lid ... .. .... ... .. .. ..... ... .. . 37
Se lective unlock feature ..... ... .. .. . 34
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Un locking and locking vehicle ......... 34
Power seat a djus tment
F ront seats . ... .. .. .. ... ..... ... .. . 51
Power steer ing
refer to E lect ro-mechanical power as-
s ist ............................. 196
Power w indows .. .. .................. 38
malfunction ... ... ........... .... .. 39
Pregnant women Spec ia l considerations when wearing a
safety be lt . . . . . . . . . . . . . . . . . . . . . . . 141
pre se nse ..... .. ................... 190
Preventative passenger protection ..... 190
Programming the Homeli nk® universa l re-
mote control .. .. .. .. ............... 124
Proper o ccupan t se ating position s ... .. 12 7
Proper safety belt position . . . . . . . . . . . . 140
Proper seating position Front passenger .... . .. .. ..... ... .. 128
Occ upants ..... .... ............... 127
Rear passengers ................... 129
Q
quattro®
refer to All-whee l drive
196
Ques tion
What happens to unbe lted o ccupants? 137
Why safety belts? . .. .. ..... ... .. .. 136
•
•

300 Index
Sunroof .......... ......... ... .... .. 40
Sun shade
Rear window ............. .... .... ..
45
Side doors . . . . . . . . . . . . . . . . . . . . . . . . . 45
Sun visors . .................. ... .. .. 45
Symbo ls
refer to Warning/indicator lights .... .. 12
T
Tachometer . . . . . . . . . . . . . . . . . . . . . 12, 23
Technical modifications .......... .... 288
Temperature disp lay .................. 23
Tether anchors .......... ...... .. .. . 188
Tether strap ................... ... . 188
The first 1,000 miles (1,500 km) and after-
wards ... .... ................ ..... .
199
Three-zone cl imate control ............ 65
Tie-downs . . . . . . . . . . . . . . . . . . . . . 62, 133
Tips for the environment
Saving fuel . . . . . . . . . . . . . . . . . . . . . . . .
60
tiptronic .. ... .............. .. .. .. . 105
tiptronic (automatic transmission) .. ... 109
Tire pressure ............... ... .... . 246
Tire pressure monitor ing system .. .. .. . 258
Loss of air pressure ......... .. .. .. . 259
Malfunct ion ............. ......... 259
Resett ing t ire pressures ............. 260
Tires .......................... ... . 240
Service life .... .... ...... ...... .. . 250
Speed rating letter code ....... .. ... 252
Tire manufacturing date ....... .... . 252
Tire specifications ................. 252
Tread depth ................ ..... . 250
Uniform tire quality grading .. ... ... . 254
Winter tires .............. ... .... . 255
Tires and vehicle load limits ........... 248
Tires and wheels
Check ing tire pressure ...... ... .. .. .
246
Cold tire inflat ion pressure ..... .. ... 244
Dimensions . .................. ... . 251
General notes . . . . . . . . . . . . . . . . . . . . . 240
Glossary of t ire and load ing termino lo-
gy .. .... .. ................ ... ...
241
Low aspect ratio tires ....... ... .... . 257
New tires and wheels .......... .... . 251
Replacing ........................ 252
Snow chains ..... ................ . 256
Tires and vehicle load limits ...... ... 248
Whee l bolts ... .. ................ . 257
Winter tires .................. .... 255
Tire service life ..................... 250
Tools .. ....... ................... . 262
Torn or frayed safety belts ......... ... 139
Touc h-up pa int ..................... 213
Towing
Tow truck procedures ...............
276
TPMS
Tire pressure monitoring system .....
259
Traile r towing .................. .... 204
Operating instructions .............. 204
Parking system ... ................ . 123
Technical requirements . . . . . . . . 204, 205
Trailer towing tips . ............... . 206
Train (transport ing your vehicle) . ...... 278
Transmission
l 't . ® 105 mu t1 ronic ..... ................ .
S tronic ® ..... ................... .
105
tiptronic ...... .. .......... ....... 105
Transmission malfunction (indicator
light) .............................
110
Transport Canada .. ................ . 134
Transporting your vehicle ............ . 278
Tread Wear Indicator (TWI) ........... 250
Trip odometer . .... .................. 27
What does it mean when DEF appears in
the trip odometer display? ....... ... .
27
T runk
refer to Luggage compartment ........ 61
Trunk escape handle ................. 261
Trunk lid
refer to Rear lid .................. .. 37
Turn signals . .. .. .. ..... ........ ..... 43
Warning/ind icator lights ............. 23
u
Undercoating ...................... 214
Unfastening safety belts ........... .. 141
U nidirectional tires ... ........... .... 240
Uniform tire quality grading .......... 254