2013 Alfa Romeo 4C wheel

88) The car must be locked after afew clicks of the parking brake: if
this is not so, contact the
dedicated Alfa Romeo Dealership
to have it adjusted. Always park
the vehicle safely as indicated by
the Highway Code and as
described above.
USING THE
TRANSMISSIONThe 4C features the TCT 6-speed twin
dry clutch transmission with steering
wheel controls. This is an advanced
technical solution which combines the
control of a manual gearbox, the
immediacy of a sequential system and
the convenience of being able to select
an automatic selection programme
without the slowdown of a conventional
automatic transmission.
With the key removed from the ignition,
the system will not implement any
action when the buttons on the
transmission control panel on the
central tunnel fig. 74 are pressed,
irrespective of the pressure applied to
the brake pedal. Therefore, the
transmission will remain in the condition
that it was in when the engine was
switched off. With car stationary and key at MAR-ON
(ignition-operated electrical services
activated), the screen displays the gear
engaged and the active operating
mode (automatic =
AUTOor manual =
no display).
OPERATING MODES
The transmission can operate in two
operating modes (except when the
"Race" mode is selected):
❒ the first manual type (MANUAL), in
which the driver decides directly
when to change gear;
❒ the second completely automatic
(AUTO), in which the system decides
when to change gear.
When the "Race" mode is selected, the
only allowed operating mode is
MANUAL.
Manual operation
(MANUAL)
In this operating mode, the driver is
responsible for choosing the best gear
to engage, depending on the car
operating conditions.
Use the “+” steering wheel stalk to
engage a higher gear, or the “–” stalk to
engage a lower gear (see the following
paragraph, "Steering wheel stalks").74
A0L0067
104
STARTING AND DRIVING
24-9-2013 11:50 Pagina 104

LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 77.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 78): engage
higher gear;
– steering wheel stalk "– (pulling stalk
towards driver, see fig. 78): engage
lower gear. The engagement of a lower (or higher)
gear is only permitted if the engine
rpm allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear
(1) or reverse (R) can be engaged.
Irrespective of the mode selected
(AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the
1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or the Rbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself to AUTOmode.
Neutral (N) can be engaged again by
pressing the Nbutton with the brake
pedal pressed.
When the 1,Nor Rbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel. Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car
start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted,
the display shows a dedicated
message.77
A0L0071
78
A0L0072
106
STARTING AND DRIVING
24-9-2013 11:50 Pagina 106

When setting off on a medium-steep
incline, it is advisable to engage the
handbrake.
Engaging 1st gear
Proceed as follows:
❒press the brake pedal;
❒ press the 1button on the
transmission control panel;
❒ release the brake pedal and press
the accelerator pedal.
Engaging reverse (R)
Reverse (R) can only be engaged with
car stationary and brake pedal pressed.
Proceed as follows:
❒ press the brake pedal (car completely
stationary);
❒ press the R button on the
transmission control panel;
❒ release the brake pedal and press
the accelerator pedal. When reverse
is engaged, the system emits an
acoustic signal (for versions/markets,
where provided).
If the brake pedal is not depressed (and
the car is stationary), the display will
show a dedicated message and the
system will automatically engage
neutral (N). IMPORTANT With the car running, the
request is accepted and executed if the
car speed drops below 3 km/h within
3 seconds from the request: if the
request is not executed, the system will
maintain the gear engaged or, if the
speed of the car drops below 10 km/h,
will put the transmission in neutral (N)
and the manoeuvre will have to be
repeated.
ENGAGING NEUTRAL (N)
With car stationary and ignition key at
MAR-ON (irrespective of the condition
of the engine), neutral (N) can only
be engaged with the brake pedal
pressed.
If the car is in motion, neutral (N) can
always be engaged, irrespective of the
pressure applied to the brake and
accelerator pedals.
The display will show the letter
N
together with the active operating
mode.
With car in motion, to engage a gear
from the neutral (N) position, press the
1 button on the transmission control
panel (it is not necessary to press
the brake pedal): the transmission will
immediately engage the correct gear
according to the car’s speed. With car stationary and ignition key at
MAR-ON (irrespective of the condition
of the engine), 1st gear can only be
engaged with the brake pedal pressed.
LAUNCH CONTROL
The "Launch Control" strategy permits
high-performance starting.
This strategy can be activated with
vehicle at a standstill, Dynamic or Race
mode selected and 1st gear engaged.
The sequence of operations to perform
is as follows:
❒
press the brake pedal and hold it
down;
❒ press the accelerator pedal and hold
it down;
❒ press the "–" stalk behind the
steering wheel;
When the brake pedal is released, the
car will start with maximum
acceleration.
89)
To abandon the strategy, simply
interrupt the above sequence
of operations or release the accelerator
pedal.
107
24-9-2013 11:50 Pagina 107

DISPLAYED
INFORMATION
When the key is turned to MAR-ON,
after about 1 second, the display
shows the transmission in neutral
indication (N). When driving, the display
shows the gear engaged and the active
mode (AUTOorMANUAL). The
indications on the display have the
following meanings:
N = neutral;
1 = first gear;
2 = second gear
3 = third gear;
4 = fourth gear;
5 = fifth gear;
6 = sixth gear;
R = reverse.
The car always starts in neutral. When
1st gear is requested, the system
forces the selection of AUTOmode.
IMPORTANT If 10 seconds elapse with
the ignition key in the MAR-ON
position and the display does not show
the gear engaged, turn the key to the
STOP position, wait for the display
to switch off and then repeat the
procedure. If the fault persists, contact
a dedicated Alfa Romeo Dealership. ACOUSTIC SIGNAL
For safety reasons, an acoustic signal is
emitted when the car is parked with
the transmission in neutral (N) (the
signal can be heard when the ignition
key is turned to
STOP).
With the car stationary, the engine
started and (1st) gear or (R) engaged,
the system activates the acoustic signal
and automatically places the
transmission in neutral (N) when:
❒ the accelerator and/or brake pedal
are not operated for at least 3
minutes;
❒ the brake pedal is pressed for longer
than 10 minutes;
❒ the driver's door is opened and the
accelerator pedal or the brake pedal
are not operated for at least one
and a half seconds;
❒ a fault has been detected in the
transmission.
PARKING THE CAR
When parking and leaving the car,
proceed as follows:
❒ engage a gear (1st gear if facing
uphill or reverse if facing downhill)
and leave the wheels turned;
❒ stop the engine and engage the
handbrake. Block the wheels with a wedge or a
stone if the car is parked on a steep
slope.
Wait until the indication of the gear
engaged disappears on the display
before releasing the brake pedal.
IMPORTANT:
NEVERleave the car with
the transmission in neutral.
GENERAL WARNINGS
❒ With car stationary and gear
engaged, always keep the brake
pedal pressed until you decide to set
off, then release the brake and
accelerate gradually.
❒ During prolonged stops with the
engine running, it is advisable to keep
the transmission in neutral (N).
❒ In order to safeguard the efficiency of
the clutch, do not use the accelerator
to keep the car stationary (e.g. when
stopped on an incline). The clutch
could overheat and be damaged: use
the brake pedal or the handbrake
and only operate the accelerator
pedal when you decide to set off.
❒ If, with reverse gear (R) engaged, you
have to engage 1st gear or vice
versa, only do this when the car is
completely stationary and with the
brake pedal pressed.
108
STARTING AND DRIVING
24-9-2013 11:50 Pagina 108

❒If it is necessary to proceed downhill
with transmission in neutral (N) for
unexpected reasons, bearing in mind
that this practice is highly inadvisable,
remember that when gear
engagement is requested, the
system will automatically engage the
best gear to permit the correct
transmission of drive torque to the
wheels, according to the speed
of the car.
❒ When necessary, it is possible to
engage 1st gear, reverse (R) or
neutral (N) with the engine off, the
key at MAR-ON and the brake
pressed. In this case, change gear
leaving at least 5 seconds between
one gear change and the next, in
order to safeguard the operation of
the hydraulic system, and the pump
in particular.
❒ For uphill departures, it is advisable
to accelerate gradually but fully
immediately after releasing the
handbrake or the brake pedal; this
allows the engine to temporarily
increase the number of revs and
tackle the steepest gradients with
more torque at the wheels.
SAVING FUELAlfa Romeo has designed and built the
vehicle using technologies, materials
and devices able to reduce negative
environmental impact. Here are some
suggestions to further contribute to
environmental protection.
GENERAL
CONSIDERATIONS
Car maintenance
Have checks and adjustments carried
out in accordance with the “Scheduled
Servicing Plan”.
Tyres
Check the tyre pressures at least once
every four weeks: if the pressure is
too low, consumption levels increase as
resistance to rolling is higher.
Climate control system
The use of the climate control system
leads to higher fuel consumption. If the
temperature outside permits, try to
use ventilation only.
109
24-9-2013 11:50 Pagina 109
WARNING
89) The Launch control function is
only available in the Dynamic or
Race mode. Regardless of what is
explicitly indicated in the
description of these modes, the
ESC and ASR systems are
deactivated during operation of
the Launch Control function. This
means that vehicle dynamic
control is always the responsibility
of the driver. Therefore pay the
utmost attention when using the
Launch Control. Take into account
traffic and road surface conditions
and during manoeuvres make
sure there is enough room in the
area concerned.

SNOW TYRESUse snow tyres of the same size as the
normal tyres provided with the car:
the dedicated Alfa Romeo Dealership
will be able to advise you on the most
appropriate tyre to use.
Only use these tyres in the event of ice
or snow on the roads.
For the type of tyre to be used, inflation
pressures and the specifications of
snow tyres, follow the instructions given
in the "Wheels" paragraph in the
"Technical specifications" chapter.
90)
The performance of these tyres on
low-grip surfaces are reduced
considerably when the tread depth is
below 4 mm. They should be replaced
in this case.
Due to the specific characteristics of
snow tyres, in normal weather
conditions or on long motorway
journeys, the performance of these
tyres is lower than that of standard
tyres. Their usage should therefore be
restricted in accordance with their
type approval.IMPORTANT When using snow tyres
with a maximum speed index below the
one that can be reached by the car
(increased by 5%), place a notice in the
passenger compartment, plainly in
view, which states the maximum speed
allowed by the snow tyres (as per EC
Directive).
All four tyres should be the same brand
to ensure greater safety when driving
and braking as well as making the
car more responsive. It is inadvisable to
change the rotation direction of tyres.
Refer to the "Raising the car" section in
the "In an emergency" chapter for
further details on how to raise the car
correctly.
WARNING
90) The maximum speed for snow
tyres marked “Q” is 160 km/h,
while it is 190 km/h for “T” tyres
and 210 km/h for "H" tyres. The
highway code speed limits must
however always be complied with.
CAR INACTIVITYIf the car is to be left inactive for longer
than a month, observe the following
precautions:
❒park the car in covered, dry and if
possible well-ventilated premises and
slightly open the windows;
❒ check that the handbrake is not
engaged;
❒ disconnect the negative battery
terminal and check the battery
charge. Repeat this check once
every three months during storage.
For optimum preservation of the
battery charge, it is advisable to use
the charge-holder (for versions/
markets, where provided, or
alternatively, available from
Lineaccessori). For more details on
its operation, refer to the attached
Supplement;
❒ if the battery is not disconnected
from the electrical system, checks its
state of charge every thirty days;
❒ clean and protect the painted parts
using protective wax;
111
24-9-2013 11:50 Pagina 111

IN AN EMERGENCY
A punctured tyre or a burnt-out bulb?
At times, a problem may interfere
with our journey.
The pages on emergencies can help
you to deal with critical situations
independently and with calm.
In an emergency we recommend that
you call the freephone number found in
the Warranty Booklet.
You can also use the freephone number
00 800 2532 4200 to find your nearest
dedicated Alfa Romeo Dealership.STARTING THE ENGINE .................114
REPAIRING A WHEEL .....................115
CHANGING A BULB .......................118
REPLACING EXTERIOR BULBS......122
INTERIOR BULB REPLACEMENT ...125
REPLACING FUSES........................126
RECHARGING THE BATTERY ........129
RAISING THE CAR..........................129
TOWING THE CAR .........................130
113
24-9-2013 11:50 Pagina 113

REPAIRING A WHEELGENERAL
INSTRUCTIONS
The car is equipped with a quick tyre
repair device called the "Fix&Go
automatic" kit.
92) 94)
To use it, follow the instructions below.
93) 95) 96)
12)
2)
"Fix&Go automatic" KIT
It is located in the luggage
compartment.
The kit includes:
❒bottle A fig. 80 containing sealant
and fitted with: filling tube B and
adhesive label C with the wording
“max. 80 km/h” to be placed in
a clearly visible position (e.g. on the
dashboard) after repairing the tyre;
❒ compressor D complete with
pressure gauge and connectors;
❒ an information leaflet fig. 81,
providing instructions for using the kit
correctly. This booklet should be
given to the persons charged with
handling the tyre treated with this kit;
❒ a pair of gloves located in the side
compartment of the compressor;
❒ adaptors for inflating different
elements. IMPORTANT The sealant is suitable for
use at temperatures in the range from
−20°C to +50°C. The sealant has an
expiry date. INFLATION PROCEDURE
Proceed as follows:
97)
❒
engage the handbrake, unscrew the
tyre valve cap, take out filler hose A
fig. 82 and tighten ring nut B on
the tyre valve;
❒ make sure that switch A fig. 83 for
the compressor is in position 0 (off),
start the engine, insert the plug
into the cigar lighter socket on the
central tunnel (see fig. 84) and switch
on the compressor by bringing
switch A fig. 83 to I (on);
❒ inflate the tyre to the pressure
indicated in the “Wheels” paragraph
in the “Technical data” chapter. In
order to obtain a more precise
reading, check the pressure value on
pressure gauge B fig. 83 with the
compressor off;
80
A0L0076
81
A0L0077
82
A0L0078
115
24-9-2013 11:50 Pagina 115