2013 Acura TL check engine

Î
This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position.
This indicator has two f unctions:If it comes on while driving, it
indicates that one or more of your
vehicle’s tires are signif icantly low
on pressure. You will also see a ‘‘CHECK TIRE
PRESSURE’’ message on the multi-
inf ormation display (see page ).
Check the tire pressure monitor on
the multi-inf ormation display and
determinethecause(seepage ).
If this indicator begins to flash,
there is a problem with the tire
pressure monitoring system
(TPMS). You will also see a
‘‘CHECK TPMS SYSTEM’’
message on the multi-
information display. The
indicator continues to flash for a
while (approximately 1 minute),
then stays on. If this happens,
have your dealer check the
system as soon as possible. For
more information, see page
.
If this happens, pull to the side of the
road when it is saf e, check which tire
has lost pressure on the multi-
inf ormation display, and determine
the cause. If it is because of a flat tire,
replace the flat tire with the compact
spare (see page ), and have the
f lat tire repaired as soon as possible.
If two or more tires are underinf lated,
call a prof essional towing service.
For more inf ormation, see page .
1.
2.
516
515
514
583
607
Instrument Panel Indicators
Low Tire Pressure/
TPMS Indicator
Inst rument s and Cont rols
69
12/07/20 10:38:38 31TK4640_074
ÎModels equipped with the keyless
access system have an engine start/
stop button instead of an ignition
switch. ON Mode is the equivalent of
ON (II). For more information, see
pages
and .
:
184 187
2013 TL

ÎThe lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.This indicator normally comes on
when you turn the ignition switch to
the ON (II) position and goes of f
af ter the engine starts. If it comes on
at any other time, there is a problem
in the electric power steering system.
If this happens, stop the vehicle in a
saf e place and turn of f the engine.
Reset the system by restarting the
engine. The indicator will stay on,
but should go of f af ter driving a
short distance. If it does not go of f ,
or comes back on again while driving,
take the vehicle to your dealer to
have it checked. With the indicator
on, the EPS may be turned of f ,
making the vehicle harder to steer.
If you turn the steering wheel to the
f ull lef t or right position repeatedly
while stopping or driving at very low
speed, you may f eel slightly harder
steering in order to prevent damage
to the steering system caused by
overheating. This may also happen if
you hold the steering wheel on the
f ull lef t or right position f or a while.
You will also see a ‘‘CHECK POWER
STEERING SYSTEM’’ message on
the multi-information display.
558 562
Instrument Panel Indicators
Turn Signal and
Hazard Warning
Indicators
Electric Power Steering
(EPS) Indicator
70
12/07/20 10:38:46 31TK4640_075
Inst rument s and Cont rols
Î
Mod els eq uip ped wit h th e keyless
a cce ss sy ste m have an en gin e sta rt/
s to p butto n in ste ad of an ignition
s w it c h .O N Mod e is th e eq uiv ale n t of
O N (II) . F or m ore in fo rm atio n ,se e
p ag es
and .
:
184 187
2013 TL

Î
This indicator is in the f uel gauge. It
comesonasareminderthatyou
must ref uel soon. You will also see a
‘‘LOW FUEL’’ message on the multi-
inf ormation display.This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. If this indicator comes on at
any other time, there is a problem in
the SH-AWD system. You will also
see a ‘‘CHECK SH-AWD SYSTEM’’
message on the multi-information
display (see page ). Take your
vehicle to a dealer to have it checked.
For more inf ormation, see page .
When the indicator comes on, there
are about 2.5 U.S. gal (9.6
)on
SH-AWD models, and 2.8 U.S. gal
(10.5
)on2WDmodelsof fuel
remaining in the tank.
When the needle reaches E, there is
a very small amount of f uel in the
tank.
505504
CONT INUED
On SH-AWD models
L ow Fuel Indicator Super Handling-A ll
Wheel Drive (SH-AWD)
Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
73
LOW FUEL INDICATOR
U.S. model is shown.
12/07/20 10:39:12 31TK4640_078
Î Models equipped with the keyless
access system have an engine start/
stop button instead of an ignition
switch. ON Mode is the equivalent of
ON (II). For more information, see
pages
and .
:
184 187
2013 TL

If the indicator blinks while driving,
the dif f erential temperature is too
high.You will also see an ‘‘SH-AWD
DIFF TEMP. HIGH’’ message
on the multi-information display
(see page ).
Pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out. This indicator normally comes on f or
a f ew seconds when you select the
ON mode with the engine start/stop
button (see page ). If it comes on
at any other time, it indicates that
there is a problem with the system. If this indicator comes on along
with a ‘‘CHECK KEYLESS
STARTING SYSTEM’’ message
on the multi-information display,
there is a problem with the keyless
starting system. In this case, your
vehicle may not restart. If you can
continue to drive saf ely, take the
vehicle to your dealer and have it
checked as soon as possible. For
more information, see page .
This indicator has two f unctions:
If this indicator comes on along
with a ‘‘CHECK KEYLESS
ACCESS SYSTEM’’ message on
the multi-information display,
there is a problem with the keyless
access system. Have the vehicle
checked by your dealer as soon as
possible. For more inf ormation,
see page .
1. 2.
505 195
196 196
On models with keyless access system
Instrument Panel Indicators
K eyless Access System
Indicator
74
Continuing to drive with the SH-AWD
indicator blinking may cause serious
damage to the system.
12/07/20 10:39:20 31TK4640_079
Inst rument s and Cont rols
2013 TL

If the indicator comes on at any
other time, there is a problem with
BSI. You will also see a ‘‘CHECK
BLIND SPOT SYSTEM’’ message on
the multi-information display. If this
happens, take your vehicle to a
dealer, and have it checked. For
more information, see page .
When this indicator is on, BSI is not
working.
This indicator normally comes on f or
a f ew seconds when you select the
ON mode by operating the engine
start/stop button (see page ).
This indicator comes on as a
reminder that you have turned of f
the blind spot inf ormation system
(BSI).
When you turn the system on, the
indicator will turn of f .
The BSI indicator also comes on if
the rear bumper becomes dirty while
driving. You will see a ‘‘BLIND
SPOT NOT AVAILABLE’’ message
on the multi-information display.
When you clean the rear bumper,
the indicator should go off after you
begin driving again. 519
185
On models with blind spot
information system (BSI)
Blind Spot Inf ormation
System (BSI) Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
75
12/07/20 10:39:25 31TK4640_080
2013 TL

This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom mark to about the
middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to the
upper zone. If it reaches the red
(hot) mark, pull saf ely to the side of
the road. Turn to page for
instructions and precautions on
checking the engine cooling system. If the pointer of the temperaturegauge reaches to or above the red
mark, you will also see the ‘‘WATER
TEMP HOT’’ message on the multi-
information display. This will alert
you that the engine should be
593
Temperature Gauge
Gauges
Inst rument s and Cont rols
77
12/07/20 10:39:34 31TK4640_082
cooled down.
2013 TL

To turn the vehicle off, make sure
the vehicle is completely stopped and
do the f ollowing.If the shif t lever is in any gear
other than neutral, depress the
clutch pedal, then press the engine
start/stop button.
The engine stops and the power
mode switches f rom ON to
VEHICLE OFF (LOCK).
Bef ore leaving the vehicle, make
sure it is of f . You can verif y if the
power is of f by checking the engine
start/stop button LED indicator.
You can only place the vehicle in the
VEHICLE OFF (LOCK) mode if the
transmission is in Park. You will see
the ‘‘SHIFT TO PARK’’ message on
the multi-information display if you
press the engine start/stop button to
turn the vehicle off with the shift
lever in any other position except
for P (Park).
If the shift lever is in neutral, press
the engine start/stop button. Press the engine start/stop button
with your f oot on the brake pedal. Shif t to park (P). Make sure to press the brake pedal
or set the parking brake before
turning off the engine. If your foot
is OFF the clutch pedal in any gear
position, pressing the engine start/
stop button turns off the engine,
and the vehicle may move
forward or backward.
1.
2.
Manual Transmission
Automatic Transmission
On automatic transmission models
On manual transmission models
Stopping the Engine
K eyless A ccess System
Operat ion Guidance
190
SHIFT TO PARK
A/T model only
A/T model
12/07/20 10:54:13 31TK4640_195
Inst rument s and Cont rols
2013 TL

CONT INUED
If you take the keyless access
remote out of the vehicle and close
the door with the power mode ON or
ACCESSORY, the inside and outside
beepers sound and a ‘‘KEYLESS
REMOTE NOT DETECTED’’
message will be displayed on the
multi-inf ormation display, and the
doors will not lock.The displayed message goes away
when you bring the remote back
inside the vehicle.
If the engine is running and you take
the remote out of the vehicle, it will
continue to run, and the inside and
outside beepers will sound. Once the
power mode is changed to VEHICLE
OFF (LOCK), the engine will not
restart until you bring back a remote
into the vehicle.
Even when the remote is inside the
vehicle, the beeper may sound when
the location of the remote is not
detected due to surrounding
conditions. It is not a f ailure. Make
sure that you carry the remote with
you. The engine does not start if you push
the engine start/stop button when
theremoteisoutsidethevehicle.
Check where the remote is. Make
sure that the remote is in the vehicle
with you when you operate the
engine start/stop button.
The outside beeper sounds when the
power mode is in ACCESSORY, and
a door is opened, then closed.
K eyless A ccess System
K eyless Remot e Not Det ect ed
Beeper and Message
Inst rument s and Cont rols
193
12/07/20 10:54:35 31TK4640_198
2013 TL