8-37
8Left side Right side
EBU25092Lubricating the steering shaft The steering shaft must be lubricated by a Yamaha
dealer at the intervals specified in the periodic
maintenance and lubrication chart.TIPFor parts equipped with a grease nipple, use a
grease gun.
1. Upper grease nipple
2. Lower grease nipple
1. Upper grease nipple
2. Lower grease nippleRecommended lubricant:
Lithium-soap-based grease
U10P70E0.book Page 37 Thursday, July 21, 2011 8:51 AM
9-1
9
EBU25860
CLEANING AND STORAGE
EBU28191Cleaning Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.
1. Before cleaning the ATV:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
c. Make sure the steering lock cap is properly
installed.
2. If the engine case is excessively greasy, apply
degreaser with a paint brush. Do not apply de-
greaser to the chain, sprockets or wheel ax-
les.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the job.
WARNING! Wet brakes may have reduced
stopping ability, increasing the chance of
an accident. Test the brakes after washing.
Apply the brakes several times at slowspeeds to let friction dry out the linings.
[EWB02311]
NOTICE: Excessive water pressure
may cause water seepage and deteriora-
tion of wheel bearings, brakes, transmis-
sion seals and electrical devices. Many
expensive repair bills have resulted from
improper high-pressure detergent applica-
tions such as those available in coin-oper-
ated car washers.
[ECB00711]
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.
5. Rinse the ATV off immediately with clean wa-
ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Dry the chain and lubricate it to prevent it from
rusting.
7. Clean the seat with a vinyl upholstery cleaner
to keep the cover pliable and glossy.
8. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
U10P70E0.book Page 1 Thursday, July 21, 2011 8:51 AM
LLabel locations ............................................................... 1-1
License plate light bulb, replacing ................................ 8-42
Light switch .................................................................... 4-4MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-1NNeutral indicator light ..................................................... 4-2OOwner’s manual and tool kit ........................................... 8-2PParking ........................................................................... 6-7
Parking brake free play, adjusting ................................ 8-26
Parking brake lever ........................................................ 4-7
Parking on a slope ......................................................... 6-7
Part locations ................................................................. 3-1RReverse indicator light .................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 2-1
Seat .............................................................................. 4-14
Shifting ........................................................................... 6-4
Shift pedal ...................................................................... 4-8
Shock absorber assemblies, adjusting the front .......... 4-14
Shock absorber assembly, adjusting the rear .............. 4-16
Spark arrester, cleaning ............................................... 8-18
Spark plug, checking ...................................................... 8-9
Specifications ............................................................... 10-1Speed limiter .................................................................. 4-5
Speedometer .................................................................. 4-2
Starter (choke) ............................................................. 4-12
Start switch ..................................................................... 4-3
Steering lock ................................................................ 4-13
Steering shaft, lubricating ............................................. 8-37
Storage ........................................................................... 9-2
Suspension, lubricating the upper and
lower arm pivots ......................................................... 8-36
Suspension relay arm and connecting arm pivoting
points, lubricating the rear ......................................... 8-35
Swingarm pivots, lubricating ........................................ 8-35
TTail/brake light bulb, replacing ..................................... 8-41
Throttle lever ........................................................... 4-4, 5-3
Throttle lever free play, adjusting ................................. 8-21
Tires ............................................................................... 5-4
Troubleshooting ........................................................... 8-45
Troubleshooting chart .................................................. 8-46
Turn signal indicator light ............................................... 4-2
Turn signal light bulb, replacing ................................... 8-42
Turn signal switch .......................................................... 4-4VValve clearance ............................................................ 8-22
Vehicle identification number ....................................... 11-1WWheel hub bearings, checking ..................................... 8-35
Wheel, installing ........................................................... 8-44
Wheel, removing .......................................................... 8-44
U10P70E0.book Page 2 Thursday, July 21, 2011 8:51 AM
