2012 YAMAHA YFM350R wheel alignment

8-6
8
5*Brake hoses 
Check for cracks or other damage, and replace if
necessary. √√√√
 Replace. Every 4 years
6 *Parking brake Check operation and adjust if necessary. √√√√√
7 *Wheels 
Check runout and for damage, and replace if nec-
essary. √ √√√
8 *Tires 
Check tread depth and for damage, and replace if
necessary.
 Check air pressure and balance, and correct if
necessary. √ √√√
9 *Wheel hub bearings 
Check for looseness or damage, and replace if
necessary. √ √√√
10 *Swingarm pivots 
Check operation and for excessive play, and re-
place bearings if necessary.
 Lubricate with lithium-soap-based grease. √√√
11 *Upper and lower
arm pivots

Lubricate with lithium-soap-based grease. √√√
12 Drive chain 
Check chain slack and adjust if necessary.
 Check rear wheel alignment and correct if neces-
sary.
 Clean and lubricate. √√√√√
13 *Drive chain rollers Check for wear and replace if necessary. √√√
NO. ITEM
CHECK OR MAINTENANCE
JOB INITIAL EVERY
Whichev- er comes first month136612
km
(mi) 320
(200) 1300
(800) 2500
(1600) 2500
(1600) 5000
(3200)
hours 20 80 160 160 320U1BS62E0.book Page 6 Monday, April 18, 2011 6:43 PM

8-30
83. If the drive chain slack is incorrect, adjust it as
follows.
To adjust the drive chain slack 1. Place the ATV on a level surface.
2. Loosen the axle holding bolts. 3. Loosen the locknut on each side of the swing-
arm. To tighten the drive chain, turn the drive
chain slack adjusting bolts in direction (a). To
loosen the drive chain, turn the adjusting bolts
in direction (b) and push the wheels forward.
Turn each adjusting bolt exactly the same
amount to maintain correct axle alignment.
NOTICE: Improper drive chain slack will
overload the engine as well as other vital
parts of the ATV and can lead to drive
chain slippage or breakage. To prevent
this from occurring, keep the drive chain
slack within the specified limits.
[ECB00542]
Drive chain slack: 25.0 –35.0 mm (0.98 –1.38 in)1. Drive chain slack
1. Axle holding bolt (upper)
2. Axle holding bolt (lower)
U1BS62E0.book Page 30 Monday, April 18, 2011 6:43 PM

8-31
8
TIPThere are alignment marks on both drive chain
pullers and an alignment mark on each side of the
swingarm. Make sure to align the same alignment
mark on both drive chain pullers with the alignment
mark on either side of the swingarm for proper
wheel alignment.4. Tighten the locknuts and the axle holding boltsto the specified torques.
EBU24882Lubricating the drive chain The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.NOTICEECB00561The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.1. Clean the drive chain with kerosene and asmall soft brush. NOTICE: To prevent dam-
aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.
[ECB00571]
1. Locknut
2. Drive chain slack adjusting bolt
3. Alignment marks
Tightening torques: Locknut:16 Nm (1.6 m ·kgf, 12 ft ·lbf)
Axle holding bolt (upper): 120 Nm (12 m· kgf, 87 ft·lbf)
Axle holding bolt (lower): 73 Nm (7.3 m ·kgf, 53 ft ·lbf)
U1BS62E0.book Page 31 Monday, April 18, 2011 6:43 PM