2012 YAMAHA XENTER 150 lock

1
2
3
4
5
6
7
8
9
6-21
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
tem, reducing braking perfor-
mance.
● Clean the filler cap before re-
moving. Use only DOT 4 brake
uid from a sealed container.● Use only the specified brake
fluid; otherwise, the rubber
seals may deteriorate, causing
leakage.● Refill with the same type of
brake uid. Adding a brake u-
id other than DOT 4 may result
in a harmful chemical reaction.● Be careful that water does not
enter the brake fluid reser-
voir when refilling. Water will
significantly lower the boiling
point of the fluid and may re-
sult in vapor lock.
ECA17640
NOTICEBrake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled uid immediately.
As the brake pads wear, it is normal
for the brake fluid level to gradually
EAU32345
Checking the brake uid level
1
1. Minimum level markBefore riding, check that the brake
fl uid is above the minimum level mark.
Check the brake fluid level with the
top of the reservoir level. Replenish
the brake fl uid if necessary.Speci ed brake uid:
DOT 4
EWA15990
WARNING
Improper maintenance can result
in loss of braking ability. Observe
these precautions:● Insufficient brake fluid may al-
low air to enter the brake sys- shoes as a set.
52S-F8199-E0_CS.indd 6-2152S-F8199-E0_CS.indd 6-21
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-29
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24181
Tail/brake light
1
1. Tail/brake lightThis model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come
on, have a Yamaha dealer check it.
EAUT3650
Replacing a front turn signal
light bulbIf a front turn signal light burns out, re-
place it as follows.
1. Remove cowling A. (See page
6-7.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
1
1. Turn signal light bulb socket
3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
4. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
5. Connect the coupler, and then in-
stall the headlight bulb cover.
6. Install the cowling together with
the headlight unit.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
52S-F8199-E0_CS.indd 6-2952S-F8199-E0_CS.indd 6-29
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-30
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT3640
Replacing an auxiliary light
bulbIf an auxiliary light bulb burns out, re-
place it as follows.
1. Remove cowling A. (See page
6-7.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
1
1. Auxiliary light bulb socket
1
1. Auxiliary light bulb3. Remove the burnt out bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by turning it clockwise.
6. Install the cowling.
1
1. Turn signal light bulb3. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
ECAU0080
NOTICEIf a turn signal light bulb of differ-
ent wattage than recommended is
used, the turn signal light ashing
may be affected.
5. Install the socket (together with
the bulb) by turning it clockwise.
6. Install the cowling.
52S-F8199-E0_CS.indd 6-3052S-F8199-E0_CS.indd 6-30
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-31
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
may be affected.
4. Install the lens by installing the
screw.
NOTICE:
Do not over-
tighten the screw, otherwise
the lens may break.
[ECA11191]EAU24330
License plate light
1
1. License plate lightIf the license plate light does not come
on, have a Yamaha dealer check the
electrical circuit or replace the bulb.
EAUT3670
Replacing a rear turn signal
light bulb1. Remove the turn signal lens by
removing the screw.
1
1. Rear turn signal light bulb2. Remove the burnt-out bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
ECAU0080
NOTICEIf a turn signal light bulb of differ-
ent wattage than recommended is
used, the turn signal light ashing
52S-F8199-E0_CS.indd 6-3152S-F8199-E0_CS.indd 6-31
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-34
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
Engine overheating
EWAT1040
WARNING
●
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot uid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
●
Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the
detent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the
cap while turning it counterclockwise, and then remove the cap.Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended
coolant as soon as possible.
52S-F8199-E0_CS.indd 6-3452S-F8199-E0_CS.indd 6-34
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

INDEXAAcceleration and deceleration ................... 5-2
Air fi lter and V-belt case air fi lter
elements ............................................... 6-15
Auxiliary light bulb, replacing .................. 6-30BBattery ..................................................... 6-25
Brake fl uid, changing .............................. 6-22
Brake fl uid level, checking ...................... 6-21
Brake lever, front ....................................... 3-7
Brake lever, rear ....................................... 3-8
Brake levers, lubricating .......................... 6-23
Brake pads and shoes, checking ............ 6-20
Braking ...................................................... 5-2CCables, checking and lubricating ............ 6-22
Care .......................................................... 7-1
Carrier ..................................................... 3-14
Catalytic converter .................................. 3-10
Centerstand, checking and lubricating .... 6-23
Coolant .................................................... 6-13
Coolant temperature warning light ............ 3-2
Cowling and panels, removing and
installing .................................................. 6-7DDimmer switch .......................................... 3-7EEngine break-in ......................................... 5-3
Engine idling speed, checking ................ 6-16
Engine oil ................................................ 6-10
Engine trouble warning light ...................... 3-3FFinal transmission oil .............................. 6-12
Front brake lever free play, checking ...... 6-19Front fork, checking ................................ 6-24
Fuel ........................................................... 3-9
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap ............................................ 3-8
Fuses, replacing ...................................... 6-27
HHandlebar switches ................................... 3-7
Headlight bulb, replacing ........................ 6-28
High beam indicator light .......................... 3-2
Horn switch ............................................... 3-7IIdentifi cation numbers ............................... 9-1
Indicator lights and warning lights ............. 3-2LLicense plate light ................................... 6-31
Luggage holder ....................................... 3-14MMaintenance, emission control system ..... 6-3
Maintenance and lubrication, periodic ...... 6-4
Main switch/steering lock .......................... 3-1
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display ................................ 3-3PParking ...................................................... 5-4
Part locations ............................................ 2-1
Passenger footrest .................................. 3-12RRear brake lever free play, adjusting ...... 6-19SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-11
Shock absorber assembly ....................... 3-13Spark plug, checking ................................. 6-9
Specifi cations ............................................ 8-1
Starting off ................................................. 5-2
Starting the engine .................................... 5-1
Start switch ............................................... 3-7
Steering, checking .................................. 6-25
Storage ..................................................... 7-3
Storage compartment (front) ................... 3-12
Storage compartment (rear) .................... 3-13
TTail/brake light ......................................... 6-29
Throttle grip and cable, checking and
lubricating ............................................. 6-23
Throttle grip free play, checking .............. 6-16
Tires ........................................................ 6-17
Tool kit ...................................................... 6-2
Troubleshooting ...................................... 6-32
Troubleshooting charts ........................... 6-33
Turn signal indicator lights ........................ 3-2
Turn signal light bulb (front), replacing .... 6-29
Turn signal light bulb (rear), replacing .... 6-31
Turn signal switch ..................................... 3-7VValve clearance ...................................... 6-17
Vehicle identifi cation number .................... 9-1WWheels .................................................... 6-19
Wheel bearings, checking ....................... 6-25
52S-F8199-E0_CS.indd 9-252S-F8199-E0_CS.indd 9-2
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black