2012 YAMAHA XENTER 150 key

1
2
3
4
5
6
7
8
9
5-4
EAU15943
OPERATION AND IMPORTANT RIDING POINTS
EAU17213
ParkingWhen parking, stop the engine, and
then remove the key from the main
switch.
EWA10311
WARNING
● Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.● Do not park on a slope or on
soft ground, otherwise the ve-
hicle may overturn, increasing
the risk of a fuel leak and re.● Do not park near grass or other
flammable materials which
might catch re.
52S-F8199-E0_CS.indd 5-452S-F8199-E0_CS.indd 5-4
2011/11/16 13:07:002011/11/16 13:07:00
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-26
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
NOTICE:
When removing the
battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive
lead.
[ECA16302]
2. If the battery will be stored for
more than two months, check it
at least once a month and fully
charge it if necessary.
3. Fully charge the battery before
installing it.
NOTICE:
When in-
stalling the battery, be sure the
key is turned to “OFF”, then
connect the positive lead be-
fore connecting the negative
lead.
[ECA16840]
4. After installing the battery, make
sure that the battery leads are
properly connected to the battery
terminals.
5. Turn the key from “ON” to “OFF”
three times in three-second in-
tervals to initialize the idle speed
control system.
manently damage the battery.
The battery is located behind panel A.
Remove the panel to access the bat-
tery. (See page 6-7.)
To charge the battery
Have a Yamaha dealer charge the
battery as soon as possible if it seems
to have discharged. Keep in mind that
the battery tends to discharge more
quickly if the vehicle is equipped with
optional electrical accessories.
ECA16521
NOTICETo charge a VRLA (Valve Regu-
lated Lead Acid) battery, a special
(constant-voltage) battery charger
is required. Using a conventional
battery charger will damage the
battery.
To store the battery
1. If the vehicle will not be used for
more than one month, remove
the battery, fully charge it, and
then place it in a cool, dry place.
always shield your eyes when
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID.
• EXTERNAL: Flush with plen-
ty of water.
• INTERNAL: Drink large quan-
tities of water or milk and im-
mediately call a physician.
• EYES: Flush with water for
15 minutes and seek prompt
medical attention.
●
Batteries produce explosive
hydrogen gas. Therefore, keep
sparks, ames, cigarettes, etc.,
away from the battery and pro-
vide suf cient ventilation when
charging it in an enclosed
space.
●
KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
ECA10620
NOTICENever attempt to remove the bat-
tery cell seals, as this would per-
52S-F8199-E0_CS.indd 6-2652S-F8199-E0_CS.indd 6-26
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-27
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
1
1. Spare fuse2. Remove the blown fuse, and then
install a new fuse of the specifi ed
amperage. WARNING! Do not
use a fuse of a higher amper-
age rating than recommended
to avoid causing extensive
damage to the electrical sys-
tem and possibly a re.
[EWA15131] EAUT3750
Replacing the fuses
1
1. Fuse boxThe fuse box is located beside the
battery compartment behind panel A.
(See page 6-7.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
ECA16530
NOTICEAlways keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
52S-F8199-E0_CS.indd 6-2752S-F8199-E0_CS.indd 6-27
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-28
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT3660
Replacing a headlight bulbThis model is equipped with a halo-
gen bulb headlight. If a headlight bulb
burns out, replace it as follows.
ECA10650
NOTICETake care not to damage the follow-
ing parts:●
Headlight bulb
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency
of the glass, the luminosity of the
bulb, and the bulb life will be ad-
versely affected. Thoroughly clean
off any dirt and ngerprints on the
headlight bulb using a cloth moist-
ened with alcohol or thinner.
●
Headlight lens
• Do not affix any type of
tinted film or stickers to the
headlight lens.
• Do not use a headlight bulb
of a wattage higher than
speci ed.1. Remove cowling A together with
the headlight unit. (See page
6-7.)
2. Remove the bulb cover, and then
disconnect the headlight coupler.
1
1. Headlight bulb cover
1
2
3
1. Headlight coupler
2. Headlight bulb holder
3. Headlight bulb
Speci ed fuses:
Main fuse:
20 A
Ignition fuse:
7.5 A
Signaling system fuse:
15 A
Headlight fuse:
15 A
Backup fuse:
7.5 ATIPAfter removing and installing the main
fuse, be sure to turn the main switch
from “ON” to “OFF” three times in
three-second intervals to initialize the
idle speed control system.
3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
52S-F8199-E0_CS.indd 6-2852S-F8199-E0_CS.indd 6-28
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black