2012 YAMAHA TZR50 oil change
[x] Cancel search: oil changePage 43 of 92
PERIODIC MAINTENANCE AND ADJUSTMENT
6-6
6
ODOMETER READING
CHECK OR ANNUAL
NO. ITEM MAINTENANCE JOB
1000 km 6000 km 12000 km 18000 km 24000 km CHECK
(600 mi) (3500 mi) (7000 mi) (10500 mi) (14000 mi)
19 * Front fork • Check operation and for oil
leakage. √ √√ √
Rear suspension
• Check operation.
√ √√ √
20 * relay arm and
• Lubricate with lithium-soap-
connecting arm
pivoting points based grease.
√√
21 * Autolube pump • Check operation.
• Bleed if necessary. √
√ √√
22Transmission oil • Check oil level.
√√ √ √ √ √• Change.√√ √
23 * Front and rear brake
switches • Check operation.
√√ √ √ √ √
24 Moving parts and
cables • Lubricate.
√ √√ √ √
• Check operation.
25 * Throttle grip • Check throttle grip free play, and
√ √√ √ √
adjust if necessary.
• Lubricate cable and grip housing.
26 * Lights, signals and
• Check operation.
switches • Adjust headlight beam. √√ √ √ √ √
1HD-F819D-E0 7/3/11 20:27 Página 43
2AS-F819D-E0.indd 4331/07/12 10:09
Page 50 of 92
EAUS1591
Transmission oil
The transmission oil level should be
checked before each ride. In addition,
the oil must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
To check the transmission oil level
1. Transmission oil filler cap
2. Transmission oil check bolt
1. Remove cowling A. (See page 6-8).
2. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion.
TIP
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
3. Remove the oil check bolt, andthen check the oil level.
TIP
The oil should be at the brim of the
check hole.
4. If the oil is below the brim of thecheck hole, remove the oil filler
cap, add sufficient oil of the
recommended type to raise it to
the correct level, and then install
the oil filler cap.
5. Install the oil check bolt, and then tighten it to the specified torque. To change the transmission oil
1. Transmission oil check bolt
2. Transmission oil drain bolt
3. Washer
1. Place an oil pan under the trans-
mission oil case to collect the
used oil.
2. Remove the drain bolt and the oil check bolt to drain the oil.
3. Install the drain bolt and the check bolt, and then tighten them
to the specified torques.
Tightening torque:Oil check bolt: 6 Nm (0.6 m•kgf, 4.3 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6
1HD-F819D-E0 7/3/11 20:27 Página 50
2AS-F819D-E0.indd 5031/07/12 10:09
Page 51 of 92
4. Remove the oil filler cap, refillwith the specified amount of the
recommended transmission oil,
and then install and tighten the oil
filler cap. NOTICE: Make sure
that no foreign material enters
the transmission case.
[ECAM1021]
5. Start the engine and let it idle for several minutes while checking
the transmission oil case for oil
leakage. If oil is leaking, imme-
diately turn the engine off and
check for the cause.
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU39087
To check the coolant level1. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion.
TIP
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level in thecoolant reservoir.
TIP
The coolant should be between the
minimum and maximum level marks.
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
3. If the coolant is at or below theminimum level mark, remove
panel A to access the coolant
reservoir. (See page 6-8).
4. Remove the coolant reservoir cap, add coolant to the maxi-
mum level mark, and then install
the reservoir cap. WARNING!
Remove only the coolant reser-
voir cap. Never attempt to
remove the radiator cap when
the engine is hot.
[EWA15161]
Recommended transmission oil: See page 8-1
Oil change quantity: 0.75 L (0.79 US qt, 0.66 Imp.qt)
Tightening torque:Transmission oil drain bolt: 17.5 Nm (1.7 m•kgf, 12.7 ft•lbf)
Oil check bolt: 6 Nm (0.6 m•kgf, 4.3 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
6
1HD-F819D-E0 7/3/11 20:27 Página 51
2AS-F819D-E0.indd 5131/07/12 10:09
Page 62 of 92
Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
EAU22731
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the TIP after the periodic maintenan-
ce and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.
Oil seals: Replace every two
years.
Brake hoses: Replace every four
years.
EAU22760
Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22784
To check the drive chain slack
1. Drive chain slack
1. Place the motorcycle on thesidestand.
TIP
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into theneutral position.
PERIODIC MAINTENANCE AND ADJUSTMENT
6-25
6
1HD-F819D-E0 7/3/11 20:27 Página 62
2AS-F819D-E0.indd 6231/07/12 10:09
Page 81 of 92
Dimensions:Overall length:2202 mm (86.7 in)
Overall width: 689 mm (27.1 in)
Overall height: 1175 mm (46.3 in)
Seat height: 820 mm (32.3 in)
Wheelbase: 1341 mm (52.8 in)
Ground clearance: 151 mm (5.94 in)
Minimum turning radius: 2900 mm (114.2 in)
Weight:Curb weight:124 kg (273 lb)
Engine:Engine type:Liquid cooled 2-stroke
Cylinder arrangement: Single cylinder
Displacement: 49 cm
3
Bore x stroke:40.3 x 39.0 mm (1.59 x 1.54 in)
Compression ratio: 11.50 : 1
Starting system: Electric starter
Lubrication system: Wet sump
Engine oil:Type:YAMALUBE 2S or 2-stroke engine oil
(JASO FC grade) or (ISO EG-C or EG-D
grade)
Engine oil quantity:Quantity: 1.40 L (1.48 US qt, 1.23 Imp.qt)
Transmission oil:Transmission oil change quantity:0.75 L (0.79 US qt, 0.66 Im.qt)
Type: SAE10W-30 type SE motor oil
Cooling system:Coolant reservoir capacity (up to the maxi-
mum level mark):0.29 L (0.31 US qt, 0.26 Imp.qt)
Radiator capacity (including all routes): 0.70 L (0.74 US qt, 0.62 Imp.qt)
Air filter:Air filter element:Wet element
Fuel:Recommended fuel:Premium unleaded gasoline only
Fuel tank capacity: 13.8 L (3.65 US gal, 3.04 Imp.gal)
Fuel reserve amount: 2.2 L (0.58 US gal, 0.48 Imp.gal)
Carburetor:Manufacturer:DELL’ORTO
Type x quantity: PHBN 16 / DELL’ORTO x1
Spark plug(s):Manufacturer/model:NGK / BR9 ES
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)
Clutch type: Wet, multiple-disc
Transmission:Primary reduction ratio:71/20 (3.55)
Secondary reduction ratio: 60/11 (5.45)
Final drive: Chain
Transmission type: Constant mesh 6-speed
Operation: Left foot operation
Gear ratio:1st:36/12 (3.00)
2nd: 33/16 (2.062)
3rd: 29/19 (1.526)
4th: 32/24 (1.227)
5th: 25/24 (1.041)
6th: 24/25 (0.960)
Chassis:Frame type:Double cradle
SPECIFICATIONS
8-1
8
1HD-F819D-E0 7/3/11 20:27 Página 81
2AS-F819D-E0.indd 8131/07/12 10:09