2012 YAMAHA MT-03 engine

INSTRUMENT AND CONTROL FUNCTIONS
3-6
1
2
3
4
5
6
7
8
9
10
Tachometer
1. Tachometer
2. Red zone
The electric tachometer allows the rid-
er to monitor the engine speed and
keep it within the ideal power range.
ECA10031CAUTION:
Do not operate the engine in the
tachometer red zone.
Red zone: 7,500 r/min and above.
Odometer, tripmeter modes
1. “SELECT” button
2. “RESET” button
Pushing the “SELECT” button switch-
es the display between the odometer
mode “ODO” and the tripmeter modes
“TRIP 1” and “TRIP 2” in the following
order:
ODO
6TRIP 1 6TRIP 2 6ODO
If the fuel level warning light comes on
(see page 3-4), the odometer display
will automatically change to the fuel
reserve tripmeter mode “F-TRIP” and
start counting the distance traveled
from that point. In that case, push the
“SELECT” button to switch the display
between the various tripmeter,
odometer modes in the following or-
der:
F-TRIP
6ODO6TRIP 1 6TRIP 2
6F-TRIP
To reset a tripmeter, select it by push-
ing the “SELECT” button, and then
push the “RESET” button for at least
four seconds. If you do not reset the
fuel reserve tripmeter manually, it will
reset itself automatically and the dis-
play will return to the prior mode after
refueling and traveling 5 km (3 mi).

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-7
Clock mode
1. Clock
2. “SELECT” button
3. “RESET” button
Turn the key to “ON”.
T
o set the clock
1. Push the “SELECT” button for at
least two seconds.
2. When the hour digits start flash-
ing, push the “RESET” button to
set the hours.
3. Push the “SELECT” button, and
the minute digits will start flash-
ing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button, and
then release it to start the clock.
Self-diagnosis devices
1. Engine trouble warning light “U”
2. Immobilizer system indicator light “ ”
This model is equipped with a self-diag-
nosis device for various electrical cir-
cuits. If any of those circuits are defec-
tive, the engine trouble warning light
will start flashing. If this occurs, have a
Yamaha dealer check the vehicle.
This model is also equipped with a
self-diagnosis device for the immobi-
lizer system.
Turn the key to "ON". If any of the im-
mobilizer system circuits are defec-
tive, the immobilizer system indicator
light will flash, and it will indicate an er-
ror code.
If this occurs, have a Yamaha dealer
check the vehicle. However, if the indi-
cator light slowly flashes five times,
and then quickly flashes two times re-
peatedly, this error could be caused by
signal interference. If this occurs, try
the following.
1. Use the code re-registering key to
start the engine.
NOTE:
Make sure there are no other immobi-
lizer keys close to the main switch,
and do not keep more than one immo-
bilizer key on the same key ring! Im-
mobilizer system keys may cause sig-
nal interference, which may prevent
the engine from starting.
2. If the engine starts, turn it off and
try starting the engine with the
standard keys.
3. If one or both of the standard keys
do not start the engine, take the
vehicle, the code re-registering
key and both standard keys to a
Yamaha dealer and have the
standard keys re-registered.

INSTRUMENT AND CONTROL FUNCTIONS
3-8
1
2
3
4
5
6
7
8
9
10
If the immobilizer system indicator
light flashes any error codes, have a
Yamaha dealer check the vehicle.
ECA11590CAUTION:
If the display indicates an error
code, the vehicle should be
checked as soon as possible in or-
der to avoid engine damage.Indicator lights brightness
control mode
●Indicator lights brightness:
This function allows you to adjust
the brightness of the indicator
lights to suit the outside lighting
conditions.
T
o adjust the brightness of the
indicator lights
1. Turn the key to “ON”.
2. Push the “SELECT” button to se-
lect ODO meter mode, and then
push the “RESET” button for at
least five seconds.
3. Release the “RESET” button, and
then select the desired lighting
brightness level by pushing the
“RESET” button.
EAU12331
Anti-theft alarm (optional)
This motorcycle can be equipped with
an optional anti-theft alarm by a Yama-
ha dealer. Contact a Yamaha dealer
for more information.

EAU12343
Handlebar switches
Left
1. Pass switch “ ”
2. Dimmer switch “ / ”
3. Horn switch “ ”
4. Turn signal switch “ ”
5. Hazard switch “ ”
Right
1. Engine stop switch “ / ”
2. Start switch “ ”
EAU12350
Pass switch “ ”
Press this switch to flash the head-
light.
EAU12400
Dimmer switch “ / ”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
EAU12500
Horn switch “ ”
Press this switch to sound the horn.
EAU12460
Turn signal switch “ ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When
released, the switch returns to the
center position. To cancel the turn sig-
nal lights, push the switch in after it
has returned to the center position.
EAU12660
Engine stop switch “/ ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emer-
gency, such as when the motorcycle
overturns or when the throttle cable is
stuck.
EAU12710
Start switch “ ”
Push this switch to crank the engine
with the starter.
ECA10050CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
INSTRUMENT AND CONTROL FUNCTIONS
3-9
3

INSTRUMENT AND CONTROL FUNCTIONS
3-10
1
2
3
4
5
6
7
8
9
10
EAU12733
Hazard switch “r”
With the key in the “ON” or Fposition,
use this switch to turn on the hazard
lights (simultaneous flashing of all turn
signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.
ECA10061CAUTION:
Do not use the hazard lights for an
extended length of time with the
engine not running, otherwise the
battery may discharge.
EAU12820
Clutch lever
1. Clutch lever
The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the han-
dlebar grip. To engage the clutch, re-
lease the lever. The lever should be
pulled rapidly and released slowly for
smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-19).
EAU12870
Shift pedal
1. Shift pedal
The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

INSTRUMENT AND CONTROL FUNCTIONS
3-12
1
2
3
4
5
6
7
8
9
10
To close the fuel tank cap
1. Push the fuel tank cap into posi-
tion with the key inserted in the
lock.
2. Turn the key counterclockwise to
the original position, remove it,
and then close the lock cover.
NOTE:
The fuel tank cap cannot be closed
unless the key is in the lock. In addi-
tion, the key cannot be removed if the
cap is not properly closed and locked.
EWA11090
WARNING0
Make sure that the fuel tank cap is
properly closed before riding.
EAU13210
Fuel
1. Fuel tank filler tube
2. Fuel level
Make sure that there is sufficient fuel
in the tank. Fill the fuel tank to the bot-
tom of the filler tube as shown.
EWA10880
WARNING0
• Do not overfill the fuel tank,
otherwise it may overflow when
the fuel warms up and expands.
• Avoid spilling fuel on the hot
engine.
ECA10070CAUTION:
Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted sur-
faces or plastic parts.
EAU13390
Recommended fuel:
PREMIUM UNLEADED
GASOLINE ONLY
Fuel tank capacity:
15.0 L (3.96 US gal) (3.29 Imp.gal)
Fuel reserve amount (when the fuel
level warning light comes on):
4.25 L (1.12 US gal) (0.93 Imp.gal)

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-13
EAUB1300
Fuel tank breather/overflow
hose
1. Fuel tank breather/overflow hose
2. Clamp
Before operating the motorcycle:
●Check the fuel tank breather/
overflow hose connection.
●Check the fuel tank breather/
overflow hose for cracks or dam-
age, and replace it if damaged.
●Make sure that the end of the fuel
tank breather/overflow hose is not
blocked, and clean it if necessary.
●Make sure that the end of the fuel
tank breather/overflow hose is
positioned inside of the clamp.
ECA11400CAUTION:
Use only unleaded gasoline. The
use of leaded gasoline will cause
severe damage to internal engine
parts, such as the valves and piston
rings, as well as to the exhaust sys-
tem.
Your Yamaha engine has been de-
signed to use premium unleaded
gasoline with a research octane num-
ber of 95 or higher. If knocking (or
pinging) occurs, use a gasoline of a
different brand. Use of unleaded fuel
will extend spark plug life and reduce
maintenance costs.
EAU13431
Catalytic converter
This model is equipped with a catalyt-
ic converter in the exhaust system.
EWA10860
WARNING0
The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-
ing any maintenance work.

INSTRUMENT AND CONTROL FUNCTIONS
3-14
1
2
3
4
5
6
7
8
9
10
To install the passenger seat
1. Projection
2. Seat holder
1. Insert the projection on the front
of the passenger seat into the
seat holder as shown, and then
push the back of the seat down to
lock it in place.
2. Remove the key.
EAUB1311
Seats
Passenger seat
1. Open
To remove the passenger seat
1. Insert the key into the seat lock,
and then turn it counterclockwise.
2. Pull the passenger seat off.
ECA10700CAUTION:
The following precautions must be
observed to prevent a fire hazard or
other damages.
●Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.
●Never park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
●Do not allow the engine to idle
too long.