2012 YAMAHA GRIZZLY 125 lock

8-32
8 7. Tighten the locknut on each brake cable.
8. Turn the brake lever free play adjusting bolt in
direction (a) to increase the free play, and in
direction (b) to decrease it.
9. Tighten the locknut at the brake lever.
10. Install the V-belt air filter element cover by in-
stalling the screw.
11. Connect the coupler, and then install the pan-
el by installing the quick fasteners.
12. Install the front carrier by installing the bolts,
and then tighten them to the specified torque.
EBU30440Adjusting the rear brake lever free play The brake lever free play must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.TIPBefore adjusting the brake lever free play, check
the rear brake shoes for wear.The brake lever free play should measure 5.0–8.0
mm (0.20–0.31 in) as shown. If the free play is in-
correct, adjust it as follows.
1. Locknut
2. Brake lever free play adjusting bolt
3. Brake lever free play
3
1
2
(b)
(a)
Tightening torque:
Front carrier bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
U1PY60E0.book Page 32 Friday, March 11, 2011 9:30 AM

8-33
81. Loosen the locknut.
2. Turn the brake lever free play adjusting bolt in
direction (a) to increase the free play, and in
direction (b) to decrease it.3. If the correct free play cannot be obtained as
described above, turn the adjusting bolt fully in
direction (a), and then adjust the free play us-
ing the brake lever free play adjusting nut on
the rear wheel hub.
4. Turn the brake lever free play adjusting nut on
the rear wheel hub in direction (a) to increase
the free play, and in direction (b) to decrease
it.
1. Brake lever free play
1
1. Locknut
2. Brake lever free play adjusting bolt
(a)
(b)2 1
U1PY60E0.book Page 33 Friday, March 11, 2011 9:30 AM

8-34
8 5. Use the adjusting bolt to obtain a precise ad-
justment if necessary, and then tighten the
locknut. If the correct free play cannot be ob-
tained, have a Yamaha dealer adjust it.
EBU24874Drive chain slack The drive chain slack should be checked before
each ride and adjusted if necessary.
To check the drive chain slack
1. Place the ATV on a level surface.
TIPWhen checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.2. Move the ATV back and forth to locate the
tightest portion of the drive chain, and then
measure the drive chain slack as shown.
3. If the drive chain slack is incorrect, adjust it as
follows.
1. Brake lever free play adjusting nut
1
(a)
(b)
Drive chain slack:
30.0 mm (1.18 in)1. Drive chain slack
1
U1PY60E0.book Page 34 Friday, March 11, 2011 9:30 AM

8-35
8To adjust the drive chain slack
1. Place the ATV on a level surface.
2. Loosen the hub stopper bolt locknut and then
the hub stopper bolt.
3. Loosen the axle holding bolts.
4. Loosen the drive chain slack adjusting bolt
locknut. To tighten the drive chain, turn the ad-
justing bolt in direction (a). To loosen the drive
chain, turn the adjusting bolt in direction (b),
and then push the wheels forward. NOTICE:
Improper drive chain slack will overloadthe engine as well as other vital parts of
the ATV and can lead to drive chain slip-
page or breakage. To prevent this from oc-
curring, keep the drive chain slack within
the specified limits.
[ECB00542]
5. Tighten the drive chain slack adjusting bolt
locknut and the axle holding bolts to the spec-
ified torques.
1. Hub stopper bolt
2. Hub stopper bolt locknut
3. Axle holding bolt (lower)
4. Axle holding bolt (upper)1
2
34
1. Locknut
2. Drive chain slack adjusting bolt
1
2
(a)
(b)
U1PY60E0.book Page 35 Friday, March 11, 2011 9:30 AM

8-36
8
NOTICEECB00551If measurement “A” of the drive chain slack ad-
justing bolt is less than 27 mm (1.06 in), have a
Yamaha dealer replace the drive chain.
6. Tighten the hub stopper bolt and hub stopper
bolt locknut to the specified torques.EBU24882Lubricating the drive chain The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.NOTICEECB00561The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.1. Clean the drive chain with kerosene and a
small soft brush. NOTICE: To prevent dam-
aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.
[ECB00571]
Tightening torques:
Drive chain slack adjusting bolt locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle holding bolt (upper):
85 Nm (8.5 m·kgf, 61 ft·lbf)
Axle holding bolt (lower):
60 Nm (6.0 m·kgf, 43 ft·lbf)1. Measurement A
1
Tightening torques:
Hub stopper bolt:
16 Nm (1.6 m·kgf, 12 ft·lbf)
Hub stopper bolt locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
U1PY60E0.book Page 36 Friday, March 11, 2011 9:30 AM

8-45
81. Remove the cover at the rear of the headlight
by pulling it off.
2. Remove the headlight bulb holder cover by
pulling it off.3. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.
4. Remove the burnt-out bulb by pulling it out.
5. Insert a new headlight bulb into the bulb hold-
er by pushing it in. NOTICE: Do not touch
the glass part of the headlight bulb to keep
it free from oil, otherwise the transparency
of the glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a cloth
moistened with alcohol or thinner.
[ECB00651]
1. Cover at the rear of the headlight
1
1. Headlight bulb holder cover
2. Headlight bulb holder
12
U1PY60E0.book Page 45 Friday, March 11, 2011 9:30 AM

8-46
8 6. Install the bulb holder by pushing it in and turn-
ing it clockwise.
7. Install the bulb holder cover and the cover at
the rear of the headlight. NOTICE: Make sure
the headlight bulb holder cover is securely
fitted over the bulb holder and seated
properly.
[ECB00671]
8. Adjust the headlight beam if necessary.
EBU25551Adjusting a headlight beam NOTICEECB00690It is advisable to have a Yamaha dealer make
this adjustment.To raise a headlight beam, turn the headlight beam
adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
1. Headlight bulb
1
1. Headlight beam adjusting screw
1(a)
(b)
U1PY60E0.book Page 46 Friday, March 11, 2011 9:30 AM

8-47
8
EBU25613Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the tail/brake light bulb holder (to-
gether with the bulb) by turning it counter-
clockwise.
2. Remove the burnt-out bulb by pushing it in
and turning it counterclockwise.
3. Insert a new bulb into the bulb holder, push it
in, and then turn it clockwise until it stops.4. Install the bulb holder (together with the bulb)
by turning it clockwise.
EBU25651Removing a wheel 1. Place the ATV on a level surface.
2. Loosen the wheel nuts.
1. Tail/brake light bulb holder
1
1. Tail/brake light bulb
2. Tail/brake light bulb holder
12
U1PY60E0.book Page 47 Friday, March 11, 2011 9:30 AM