2012 YAMAHA CYGNUS 125 lock

1
2
3
4
5
6
7
8
9
3-10
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
EAUT1503
SeatTo open the seat
1. Place the scooter on the center-
stand.
2. Insert the key into the main
switch, and then turn it coun-
terclockwise to the first “OPEN”
position. If the main switch is in
the “LOCK” position, turn the key
counterclockwise to the second
“OPEN” position.ZAUM00**TIPDo not push inward when turning the
key from “OFF” to “OPEN” or from
“LOCK” to “OPEN”.
3. Fold the seat up.
To close the seat
1. Fold the seat down, and then
push it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left
unattended.TIPMake sure that the seat is properly se-
cured before riding.
EAUT1713
Storage compartmentsFront storage compartmentZAUM00**
1
1. Front storage compartment
EWA11191
WARNING
● Do not exceed the load limit of
1.5 kg (3.3 lb) for the front stor-
age compartment.● Do not exceed the maximum
load of 157 kg (346 lb) for the
vehicle.
4P9-F8199-E5_CS.indd 3-104P9-F8199-E5_CS.indd 3-10
2011/09/06 14:18:402011/09/06 14:18:40
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-20
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
tem, reducing braking perfor-
mance.
● Clean the filler cap before re-
moving. Use only DOT 4 brake
uid from a sealed container.● Use only the specified brake
fluid; otherwise, the rubber
seals may deteriorate, causing
leakage.● Refill with the same type of
brake uid. Adding a brake u-
id other than DOT 4 may result
in a harmful chemical reaction.● Be careful that water does not
enter the brake fluid reser-
voir when refilling. Water will
significantly lower the boiling
point of the fluid and may re-
sult in vapor lock.
ECA17640
NOTICEBrake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled uid immediately.
As the brake pads wear, it is normal
for the brake fluid level to gradually go down. A low brake fl uid level may
indicate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fl uid level goes down suddenly, have
a Yamaha dealer check the cause be-
fore further riding.
EAU22721
Changing the brake uidHave a Yamaha dealer change the
brake fl uid at the intervals specifi ed in
the TIP after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cyl-
inder and caliper as well as the brake
hose replaced at the intervals listed
below or whenever they are damaged
or leaking.● Oil seals: Replace every two
years.● Brake hose: Replace every four
years.
4P9-F8199-E5_CS.indd 6-204P9-F8199-E5_CS.indd 6-20
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-28
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT1892
Replacing a front turn signal
light bulb
ECA10670
NOTICEIt is advisable to have a Yamaha
dealer perform this job.
1. Place the scooter on the center-
stand.
2. Remove panel A. (See page 6-7.)
3. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
4. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.ZAUM00**
1
2
1. Turn signal light bulb
2. Socket
5. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
6. Install the socket (together with
the bulb) by turning it clockwise.
7. Install the panel.
EAUT1923
Replacing the tail/brake light
bulb or a rear turn signal light
bulbZAUM00**3
1
2
4
1. Tail/brake light lens
2. Turn signal light lens
3. Rear turn signal light bulb
4. Tail/brake light bulbTail/brake light bulb
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
4P9-F8199-E5_CS.indd 6-284P9-F8199-E5_CS.indd 6-28
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-29
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENTRear turn signal light bulb
1. Remove the tail/brake light lens
by removing the screws.
2. Remove the turn signal light lens
by removing the screws.
3. Remove the burnt out bulb by
pushing it in and turning it coun-
terclockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the turn signal light lens by
installing the screws.
6. Install the tail/brake light lens
by installing the screws.
NO-
TICE:
Do not overtighten the
screws, otherwise the lens may
break.[ECA10681]EAUT1963
Replacing an auxiliary light
bulbZAUM00**
12
1. Auxiliary light bulb
2. SocketThis model is equipped with two aux-
iliary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove panel B. (See page 6-7.)
2. Remove the auxiliary light socket
(together with the bulb) by turning
it counterclockwise.
3. Remove the burnt out bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket
(together with the bulb) by turning
it clockwise.
6. Install the panel.
EAU25861
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy pro-
cedure for checking these vital sys-
tems yourself. However, should your
scooter require any repair, take it to a
Yamaha dealer, whose skilled techni-
cians have the necessary tools, expe-
rience, and know-how to service the
scooter properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15141
WARNING
When checking the fuel system, do
not smoke, and make sure there
are no open flames or sparks in
4P9-F8199-E5_CS.indd 6-294P9-F8199-E5_CS.indd 6-29
2011/09/06 14:18:412011/09/06 14:18:41
Process BlackProcess Black

INDEXAAcceleration and deceleration ................... 5-2
Air fi lter and V-belt case air fi lter
elements ............................................... 6-13
Auxiliary light bulb, replacing .................. 6-29BBattery ..................................................... 6-24
Brake fl uid, changing .............................. 6-20
Brake fl uid level, checking ...................... 6-19
Brake lever, front ....................................... 3-6
Brake lever, rear ....................................... 3-6
Brake levers, lubricating .......................... 6-21
Brake lever free play, checking ............... 6-18
Brake pads and shoes, checking ............ 6-19
Braking ...................................................... 5-2CCables, checking and lubricating ............ 6-21
Care .......................................................... 7-1
Catalytic converters .................................. 3-9
Centerstand and sidestand, checking and
lubricating ............................................. 6-22DDimmer switch .......................................... 3-6EEngine break-in ......................................... 5-3
Engine oil and oil strainer ........................ 6-10
Engine trouble warning light ...................... 3-2FFinal transmission oil .............................. 6-12
Front fork, checking ................................ 6-23
Fuel ........................................................... 3-7
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap ............................................ 3-7
Fuses, replacing ...................................... 6-26
HHandlebar switches ................................... 3-5
Headlight bulb, replacing ........................ 6-27
High beam indicator light .......................... 3-2
Horn switch ............................................... 3-6IIdentifi cation numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-12
Indicator and warning lights ...................... 3-2KKeyhole cover ........................................... 3-2
Kickstarter ................................................. 3-9MMaintenance, emission control system ..... 6-3
Maintenance and lubrication, periodic ...... 6-4
Main switch/steering lock .......................... 3-1
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display ................................ 3-3PPanels, removing and installing ................ 6-7
Parking ...................................................... 5-4
Part locations ............................................ 2-1RRear brake lever free play, adjusting ...... 6-18SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-10
Sidestand ................................................ 3-11
Spark plug, checking ................................. 6-8
Specifi cations ............................................ 8-1
Speedometer ............................................ 3-3
Starting off ................................................. 5-2Starting the engine .................................... 5-1
Start switch ............................................... 3-6
Steering, checking .................................. 6-23
Storage ..................................................... 7-4
Storage compartments ............................ 3-10
TTail/brake light bulb or rear turn signal light
bulb, replacing ...................................... 6-28
Throttle grip and cable, checking and
lubricating ............................................. 6-21
Throttle grip free play, checking .............. 6-15
Tires ........................................................ 6-16
Tool kit ...................................................... 6-2
Troubleshooting ...................................... 6-29
Troubleshooting chart ............................. 6-31
Turn signal indicator light .......................... 3-2
Turn signal light bulb (front), replacing .... 6-28
Turn signal switch ..................................... 3-6VValve clearance ...................................... 6-15
Vehicle identifi cation number .................... 9-1WWheels .................................................... 6-17
Wheel bearings, checking ....................... 6-24
4P9-F8199-E5_CS.indd 9-24P9-F8199-E5_CS.indd 9-2
2011/09/06 14:18:422011/09/06 14:18:42
Process BlackProcess Black