27
26
Getting
Started Instrument
Panel Gauges
Personalize Controls While
OperatingSafety / In Case
of Emergency Additional
Information
Impreza WRX Engine Compartment
1
1. Power Steering Fluid Reservoir Check your power steering fluid level
monthly. The power steering fluid expands
greatly as its temperature rises and
the fluid level differs according to fluid
temperature. Therefore, the reservoir tank
has two different checking ranges for
hot and cold fluid. Please refer to your
Owner’s Manual for details.
2. Air Cleaner Element This element filters intake air. Follow the
N B J O U F O B O D F H V J E F M J O F T J O Z P V S i 8 B S S B O U Z
B O E . B J O U F O B O D F w C P P L M F U 8 I F O
necessary, replace this element with a
genuine Subaru air cleaner.
3. Radiator Cap If your engine overheats, safely pull off the
road and stop your vehicle in a safe place.
/ F W F S B U U F N Q U U P S F N P W F U I F S B E J B U P S D B Q
until the engine has been shut off and has
fully cooled down. If steam is coming from
the engine compartment, turn the engine
off and move everyone away from the
vehicle until it cools. Please refer to your
Owner’s Manual for details. 4. Intercooler
The intercooler is positioned behind
the throttle body to cool intake air and
improve supercharging efficiency. (Intake
air passing through the turbocharger gets
very warm, which could result in lower
supercharging efficiency.) To prevent
damage to this important system, avoid
placing tools and other objects on
the intercooler.
5. Engine Oil Level Gauge Check the engine oil level at each fuel
stop. Pull out the dipstick, wipe it clean,
and insert it again. Pull it out and check
the oil level. If it’s below the lower level,
add oil to bring the level up to the
upper level. (Use only engine oil of the
recommended grade and viscosity.
Please refer to your Owner’s Manual
for oil recommendations and other
important details.) 6. Engine Coolant Reservoir
Check your coolant level at each
fuel stop. Observe the coolant
level on the outside of the reservoir
while the engine is cool. If the level
J T D M P T F U P o P S M P X F S U I B O o U I F
i - 0 8 w M F W F M N B S L
B E E D P P M B O U U P
U I F i ' 6 - - w M F W F M N B S L * G U I F S F T F S W F
tank is empty, remove the radiator
cap and refill as required. Please
refer to your Owner’s Manual for
details.
7. Engine Oil Filler Cap Change your oil according to
the maintenance schedule in
Z P V S i 8 B S S B O U Z B O E . B J O U F O B O D F
# P P L M F U w : P V S F O H J O F P J M N V T U C F
changed more frequently when you
drive on dusty roads, frequently
make short trips, or when you drive
in extremely cold weather.
8. Brake Fluid Reservoir Check your brake fluid level
monthly. Observe the fluid level on
the outside of the reservoir. If the
M F W F M J T C F M P X U I F i . * / w M F W F M N B S L
add the recommended brake fluid
' . 7 4 4 / P
G S F T I % 0 5 P S
C S B L F þ V J E
U P U I F i . " 9 w M F W F M
mark. Use only brake fluid from
a sealed container.
9. Battery When your vehicle does not start
due to a battery that has run down,
the vehicle may be jump-started by
connecting your battery to another
battery with jumper cables. Jump-starting is dangerous if
done incorrectly. Please refer
to your Owner’s Manual for
instructions. If you’re unsure
about how to jump-start your
vehicle, please consult a
competent mechanic.
10. Windshield Washer Tank It’s a good idea to check your washer fluid every time you stop
for fuel. If the level is low, fill the
windshield washer tank to the
neck of the reservoir with
windshield washer fluid. In cold
weather, use a freeze resistant
windshield washer fluid.
11. Main Fuse Box Your Impreza WRX has two fuse boxes. One is located under the
instrument panel, behind the
fuse box cover on the driver’s
seat side. The other is housed
in your engine compartment, as
shown here. Fuses are designed
to melt during an overload
situation in order to prevent
damage to the wiring harness and
electrical equipment. If any lights,
accessories or electrical controls
fail to operate properly, inspect
the corresponding fuse. If it has
blown, replace it in accordance
with the instructions in your
Owner’s Manual. The fuse puller
and spare fuses are located
in the main fuse box in the
engine compartment.
119
3
8
5
7
10
2
4
6
27
GetGttintigStartedInsItrument PanelGauGgesPerPsonalilizeConCtrotlslWhile OperatingSafSfetyt / /In ICasCeof EmergencyAddAdditiiional lInformation
While
Operating
29
28
Getting
Started Instrument
Panel Gauges
Personalize Controls While
OperatingSafety / In Case
of Emergency Additional
Information
Impreza WRX STI Engine Compartment
1
1. Power Steering Fluid Reservoir Check your power steering fluid level
monthly. The power steering fluid expands
greatly as its temperature rises and
the fluid level differs according to fluid
temperature. Therefore, the reservoir tank
has two different checking ranges for
hot and cold fluid. Please refer to your
Owner’s Manual for details.
2. Air Cleaner Element This element filters intake air. Follow the
N B J O U F O B O D F H V J E F M J O F T J O Z P V S i 8 B S S B O U Z
B O E . B J O U F O B O D F w C P P L M F U 8 I F O
necessary, replace this element with a
genuine Subaru air cleaner.
3. Radiator Cap If your engine overheats, safely pull off the
road and stop your vehicle in a safe place.
/ F W F S B U U F N Q U U P S F N P W F U I F S B E J B U P S D B Q
until the engine has been shut off and has
fully cooled down. If steam is coming from
the engine compartment, turn the engine
off and move everyone away from the
vehicle until it cools. Please refer to your
Owner’s Manual for details. 4. Intercooler
The intercooler is positioned behind
the throttle body to cool intake air and
improve supercharging efficiency. (Intake
air passing through the turbocharger gets
very warm, which could result in lower
supercharging efficiency.) To prevent
damage to this important system, avoid
placing tools and other objects on
the intercooler.
5. Engine Oil Level Gauge Check the engine oil level at each fuel
stop. Pull out the dipstick, wipe it clean,
and insert it again. Pull it out and check
the oil level. If it’s below the lower level,
add oil to bring the level up to the
upper level. (Use only engine oil of the
recommended grade and viscosity.
Please refer to your Owner’s Manual
for oil recommendations and other
important details.) 6. Engine Coolant Reservoir
Check your coolant level at each
fuel stop. Observe the coolant
level on the outside of the reservoir
while the engine is cool. If the level
J T D M P T F U P o P S M P X F S U I B O o U I F
i - 0 8 w M F W F M N B S L
B E E D P P M B O U U P
U I F i ' 6 - - w M F W F M N B S L * G U I F S F T F S W F
tank is empty, remove the radiator
cap and refill as required. Please
refer to your Owner’s Manual for
details.
7. Engine Oil Filler Cap Change your oil according to
the maintenance schedule in
Z P V S i 8 B S S B O U Z B O E . B J O U F O B O D F
# P P L M F U w : P V S F O H J O F P J M N V T U C F
changed more frequently when you
drive on dusty roads, frequently
make short trips, or when you drive
in extremely cold weather.
8. Brake Fluid Reservoir Check your brake fluid level
monthly. Observe the fluid level on
the outside of the reservoir. If the
M F W F M J T C F M P X U I F i . * / w M F W F M N B S L
add the recommended brake fluid
' . 7 4 4 / P
G S F T I % 0 5 P S
C S B L F þ V J E
U P U I F i . " 9 w M F W F M
mark. Use only brake fluid from
a sealed container.
9. Battery When your vehicle does not start
due to a battery that has run down,
the vehicle may be jump-started by
connecting your battery to another
battery with jumper cables. Jump-starting is dangerous if
done incorrectly. Please refer
to your Owner’s Manual for
instructions. If you’re unsure about
how to jump-start your vehicle,
please consult a competent
mechanic.
10. Windshield Washer Tank It’s a good idea to check your washer fluid every time you stop
for fuel. If the level is low, fill the
windshield washer tank to the
neck of the reservoir with
windshield washer fluid. In cold
weather, use a freeze resistant
windshield washer fluid.
11. Main Fuse Box Your Impreza WRX STI has two fuse boxes. One is located under
the instrument panel, behind
the fuse box cover on the driver’s
seat side. The other is housed
in your engine compartment, as
shown here. Fuses are designed
to melt during an overload
situation in order to prevent
damage to the wiring harness and
electrical equipment. If any lights,
accessories or electrical controls
fail to operate properly, inspect
the corresponding fuse. If it has
blown, replace it in accordance
with the instructions in your
Owner’s Manual. The fuse puller
and spare fuses are located in
the main fuse box in the
engine compartment.
11
9
3
8
5
7
10
2
4
6
29
GetGttintigStartedInsItrument PanelGauGgesPerPsonalilizeConCtrotlslWhile OperatingSafSfetyt / /In ICasCeof EmergencyAddAdditiiional lInformation
While
Operating
Black plate (75,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
3. Ensure that the backward-forward
position and seatback of front passenger ’s
seat are locked into place securely by
moving the seat back and forth.
4. Turn the ignition switch to the “ON”
position and wait 6 seconds to allow the
system to complete self-checking. Follow-
ing the system check, both indicators turn
off for 2 seconds. Now, the ON indicator
should illuminate while the OFF indicator
remains off.
If the OFF indicator still remains illumi-
nated while the ON indicator remains off,
ask the occupant to move to the rear seat
and immediately contact your SUBARU
dealer for an inspection.
! Effect vehicle modifications made
for persons with disabilities may
have on SUBARU advanced frontal
airbag system operation (U.S. only)
Changing or moving any parts of the front
seats, rear seat, seatbelts, front bumper,
front side frame, radiator panel, instrument
panel, combination meter, steering wheel,
steering column, tire, suspension or floor
panel can affect the operation of the
SUBARU advanced airbag system. If
you have any questions, you may contact
the following SUBARU distributors.
Subaru of America, Inc.
Customer Dealer Services Department
P.O. Box 6000
Cherry Hill, NJ 08034-6000
1-800-SUBARU3 (1-800-782-2783)
Servco Subaru Inc., dba Subaru Hawaii
2850 Pukoloa Street, Suite 202, Honolulu,
HI 96819
808-839-2273
Shen
’s Corporation dba Prestige Automo-
bile
491, East Marine Drive, Route 1 Dededo,
Guam
671-633-2698
Trebol Motors
P.O. Box 11204, San Juan, Puerto Rico
00910
787-793-2828
There are currently no SUBARU distribu-
tors in any other U.S. territories. If you are
in such an area, please contact the
SUBARU distributor or dealer from which
you bought your vehicle.
& System operation
CAUTION
Do not touch the SRS airbag system
components with bare hands right
after deployment. Doing so can
cause burns because the compo-
nents can be very hot as a result of
deployment.
The SRS airbags can function only when
the ignition switch is in the “ON”position.
When the SRS airbag(s) deploy(s), a
sudden, fairly loud inflation noise will be
heard and some smoke will be released.
These occurrences are a normal result of
the deployment. This smoke does not
indicate a fire in the vehicle.Seat, seatbelt and SRS airbags
1-47
– CONTINUED –
1
Black plate (180,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
4-12
Climate control
properly and become damaged, the sys-
tem may not be able to control the interior
temperature correctly. To avoid damaging
the sensors, observe the following pre-
cautions.
– Do not subject the sensors to impact.
– Keep water away from the sensors.
– Do not cover the sensors.
The sensors are located as follows.
– Solar sensor: beside the windshield
defroster grille.
– Interior air temperature sensor: near
the ignition switch.
– Outside temperature sensor: behind
the front grille.
Operating tips for heater and
air conditioner& Cleaning ventilation grilleAlways keep the front ventilation inlet grille
free of snow, leaves, or other obstructions
to ensure efficient heating and defrosting.
Since the condenser is located in front of
the radiator, this area should be kept clean
because cooling performance is impaired
by any accumulation of insects and leaves
on the condenser.&Efficient cooling after parking
in direct sunlightAfter parking in direct sunlight, drive with
the windows open for a few minutes to
allow outside air to circulate into the heated interior. This results in quicker
cooling by the air conditioner. Keep the
windows closed during the operation of
the air conditioner for maximum cooling
efficiency.
&
Lubrication oil circulation in
the refrigerant circuitOperate the air conditioner compressor at
a low engine speed (at idle or low driving
speeds) a few minutes each month during
the off-season to circulate its oil.&Checking air conditioning
system before summer sea-
sonCheck the air conditioner unit for refriger-
ant leaks, hose conditions, and proper
operation each spring. Have the air con-
ditioning system checked by your
SUBARU dealer.&Cooling and dehumidifying in
high humidity and low tem-
perature weather conditionsUnder certain weather conditions (high
relative humidity, low temperatures, etc.) a
small amount of water vapor emission
from the air outlets may be noticed. This
condition is normal and does not indicate
any problem with the air conditioning
Black plate (221,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
let on a circuit different from that to
which the receiver is connected.
. Consult the dealer or an experi-
enced radio/TV technician for help.
. Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user ’s authority to operate the equip-
ment.
. This equipment complies with FCC/
IC radiation exposure limits set forth
for an uncontrolled equipment and
meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C
to OET65 and RSS-102 of the IC radio
frequency (RF) Exposure rules. This
equipment has very low levels of RF
energy that it deemed to comply with-
out maximum permissive exposure
evaluation (MPE). But it is desirable
that it should be installed and operated
keeping the radiator at least 20 cm or
more away from person ’s body (ex-
cluding extremities: hands, wrists, feet
and ankles).
. This transmitter must not be co-
located or operated in conjunction with
any other antenna or transmitter.
& Safety precautions
WARNING
. For safety reasons, avoid operat-
ing the cell phone while driving.
. Do not make a phone call while
driving. When you have an in-
coming call, stop the vehicle in a
safe location before taking the
incoming phone call. When you
have to absolutely take a phone
call, tell the caller “I’ll call you
back ”. And then call the caller
back after stopping the vehicle in
a safe location.
CAUTION
. Do not leave the cell phone in the
vehicle. The temperature in the
vehicle may become extremely
high and cause a malfunction of
the cell phone.
. When using the cell phone, be
careful not to get it close to the
in-vehicle equipment. Getting it
too close to the in-vehicle equip-
ment may result in deterioration
in tone quality or a poor connect-
ing condition. .
In the frequency band used by
this equipment, along with indus-
trial, scientific and medical
equipment such as a microwave
oven, radio stations (a license is
required) to be used by the
production line in the factory to
identify movable bodies, specific
small power radio stations (a
license is not required) and ama-
teur radio stations (a license is
required) are being operated.
(These three types of radio sta-
tions are hereinafter referred to
as “other radio stations. ”) Before
using this equipment, be sure to
check to see if “other radio
stations ”are being operated in
the vicinity. If there is detrimental
radio interference from this
equipment to “other radio sta-
tions, ”move the equipment to
another location as soon as
possible to avoid radio interfer-
ence. The frequency band used
by this equipment is in the 2.4
GHz zone. The FH-SS modulation
is employed as a modulation
method. The expected inflicting
interference distance is less than
33 ft (10 m). This equipment uses
a full band and can avoid a band
Audio
5-37
– CONTINUED –
5
Black plate (318,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
9-12
In case of emergency
Engine overheating
WARNING
Never attempt to remove the radia-
tor cap until the engine has been
shut off and has fully cooled down.
When the engine is hot, the coolant
is under pressure. Removing the
cap while the engine is still hot
could release a spray of boiling hot
coolant, which could burn you very
seriously.
If the engine overheats, safely pull off the
road and stop the vehicle in a safe place.& If steam is coming from the
engine compartmentTurn off the engine and get everyone
away from the vehicle until it cools down.&If no steam is coming from
the engine compartment
NOTEFor details about how to check the
coolant level or how to add coolant,
refer to “Engine coolant ”F 11-12.
1. Keep the engine running at idling
speed. 2. Open the hood to ventilate the engine
compartment. Refer to
“Engine hood ”
F 11-5.
Confirm that the cooling fan is turning. If
the fan is not turning, immediately turn off
the engine and contact your authorized
dealer for repair.
3. After the engine coolant temperature
has dropped, turn off the engine.
If temperature gauge stays in the over-
heated zone, turn off the engine. Refer to
“Temperature gauge ”F 3-10.
4. After the engine has fully cooled down,
check the coolant level in the reserve
tank.
If the coolant level is below the “LOW”
mark, add coolant up to the “FULL”mark.
5. If there is no coolant in the reserve
tank, add coolant to the reserve tank.
Then remove the radiator cap and fill the
radiator with coolant.
If you remove the radiator cap from a hot
radiator, first wrap a thick cloth around the
radiator cap, then turn the cap counter-
clockwise slowly without pressing down
until it stops. Release the pressure from
the radiator. After the pressure has been
fully released, remove the cap by pressing
down and turning it.
TowingIf towing is necessary, it is best done by
your SUBARU dealer or a commercial
towing service. Observe the following
procedures for safety.
WARNING
Never tow AWD models with the
front wheels raised off the ground
while the rear wheels are on the
ground, or with the rear wheels
raised off the ground while the front
wheels are on the ground. This will
cause the vehicle to spin away due
to the operation or deterioration of
the center differential.
Black plate (336,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
11-6
Maintenance and service
Engine compartment overview& Turbo models except STI
1) Power steering fluid reservoir
(page 11-17)
2) Manual transmission oil level gauge (MT) (page 11-15)
3) Clutch fluid reservoir (page 11-19)
4) Brake fluid reservoir (page 11-18)
5) Fuse box (page 11-37)
6) Battery (page 11-36)
7) Windshield washer tank (page 11-31)
8) Engine oil filler cap (page 11-8)
9) Engine coolant reservoir (page 11-12)
10) Engine oil level gauge (page 11-8)
11) Radiator cap (page 11-12)
12) Air cleaner case (page 11-13)
Black plate (337,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
& STI
1) Power steering fluid reservoir
(page 11-17)
2) Clutch fluid reservoir (page 11-19)
3) Brake fluid reservoir (page 11-18)
4) Fuse box (page 11-37)
5) Battery (page 11-36)
6) Windshield washer tank (page 11-31)
7) Engine oil filler cap (page 11-8)
8) Engine coolant reservoir (page 11-12)
9) Engine oil level gauge (page 11-8)
10) Radiator cap (page 11-12)
11) Air cleaner case (page 11-13) Maintenance and service
11-7
11