2012 SUBARU IMPREZA WRX STI jump start
[x] Cancel search: jump startPage 16 of 463
27
26
Getting
Started Instrument
Panel Gauges
Personalize Controls While
OperatingSafety / In Case
of Emergency Additional
Information
Impreza WRX Engine Compartment
1
1. Power Steering Fluid Reservoir Check your power steering fluid level
monthly. The power steering fluid expands
greatly as its temperature rises and
the fluid level differs according to fluid
temperature. Therefore, the reservoir tank
has two different checking ranges for
hot and cold fluid. Please refer to your
Owner’s Manual for details.
2. Air Cleaner Element This element filters intake air. Follow the
N B J O U F O B O D F H V J E F M J O F T J O Z P V S i 8 B S S B O U Z
B O E . B J O U F O B O D F w C P P L M F U 8 I F O
necessary, replace this element with a
genuine Subaru air cleaner.
3. Radiator Cap If your engine overheats, safely pull off the
road and stop your vehicle in a safe place.
/ F W F S B U U F N Q U U P S F N P W F U I F S B E J B U P S D B Q
until the engine has been shut off and has
fully cooled down. If steam is coming from
the engine compartment, turn the engine
off and move everyone away from the
vehicle until it cools. Please refer to your
Owner’s Manual for details. 4. Intercooler
The intercooler is positioned behind
the throttle body to cool intake air and
improve supercharging efficiency. (Intake
air passing through the turbocharger gets
very warm, which could result in lower
supercharging efficiency.) To prevent
damage to this important system, avoid
placing tools and other objects on
the intercooler.
5. Engine Oil Level Gauge Check the engine oil level at each fuel
stop. Pull out the dipstick, wipe it clean,
and insert it again. Pull it out and check
the oil level. If it’s below the lower level,
add oil to bring the level up to the
upper level. (Use only engine oil of the
recommended grade and viscosity.
Please refer to your Owner’s Manual
for oil recommendations and other
important details.) 6. Engine Coolant Reservoir
Check your coolant level at each
fuel stop. Observe the coolant
level on the outside of the reservoir
while the engine is cool. If the level
J T D M P T F U P o P S M P X F S U I B O o U I F
i - 0 8 w M F W F M N B S L
B E E D P P M B O U U P
U I F i ' 6 - - w M F W F M N B S L * G U I F S F T F S W F
tank is empty, remove the radiator
cap and refill as required. Please
refer to your Owner’s Manual for
details.
7. Engine Oil Filler Cap Change your oil according to
the maintenance schedule in
Z P V S i 8 B S S B O U Z B O E . B J O U F O B O D F
# P P L M F U w : P V S F O H J O F P J M N V T U C F
changed more frequently when you
drive on dusty roads, frequently
make short trips, or when you drive
in extremely cold weather.
8. Brake Fluid Reservoir Check your brake fluid level
monthly. Observe the fluid level on
the outside of the reservoir. If the
M F W F M J T C F M P X U I F i . * / w M F W F M N B S L
add the recommended brake fluid
' . 7 4 4 / P
G S F T I % 0 5 P S
C S B L F þ V J E
U P U I F i . " 9 w M F W F M
mark. Use only brake fluid from
a sealed container.
9. Battery When your vehicle does not start
due to a battery that has run down,
the vehicle may be jump-started by
connecting your battery to another
battery with jumper cables. Jump-starting is dangerous if
done incorrectly. Please refer
to your Owner’s Manual for
instructions. If you’re unsure
about how to jump-start your
vehicle, please consult a
competent mechanic.
10. Windshield Washer Tank It’s a good idea to check your washer fluid every time you stop
for fuel. If the level is low, fill the
windshield washer tank to the
neck of the reservoir with
windshield washer fluid. In cold
weather, use a freeze resistant
windshield washer fluid.
11. Main Fuse Box Your Impreza WRX has two fuse boxes. One is located under the
instrument panel, behind the
fuse box cover on the driver’s
seat side. The other is housed
in your engine compartment, as
shown here. Fuses are designed
to melt during an overload
situation in order to prevent
damage to the wiring harness and
electrical equipment. If any lights,
accessories or electrical controls
fail to operate properly, inspect
the corresponding fuse. If it has
blown, replace it in accordance
with the instructions in your
Owner’s Manual. The fuse puller
and spare fuses are located
in the main fuse box in the
engine compartment.
119
3
8
5
7
10
2
4
6
27
GetGttintigStartedInsItrument PanelGauGgesPerPsonalilizeConCtrotlslWhile OperatingSafSfetyt / /In ICasCeof EmergencyAddAdditiiional lInformation
While
Operating
Page 17 of 463
29
28
Getting
Started Instrument
Panel Gauges
Personalize Controls While
OperatingSafety / In Case
of Emergency Additional
Information
Impreza WRX STI Engine Compartment
1
1. Power Steering Fluid Reservoir Check your power steering fluid level
monthly. The power steering fluid expands
greatly as its temperature rises and
the fluid level differs according to fluid
temperature. Therefore, the reservoir tank
has two different checking ranges for
hot and cold fluid. Please refer to your
Owner’s Manual for details.
2. Air Cleaner Element This element filters intake air. Follow the
N B J O U F O B O D F H V J E F M J O F T J O Z P V S i 8 B S S B O U Z
B O E . B J O U F O B O D F w C P P L M F U 8 I F O
necessary, replace this element with a
genuine Subaru air cleaner.
3. Radiator Cap If your engine overheats, safely pull off the
road and stop your vehicle in a safe place.
/ F W F S B U U F N Q U U P S F N P W F U I F S B E J B U P S D B Q
until the engine has been shut off and has
fully cooled down. If steam is coming from
the engine compartment, turn the engine
off and move everyone away from the
vehicle until it cools. Please refer to your
Owner’s Manual for details. 4. Intercooler
The intercooler is positioned behind
the throttle body to cool intake air and
improve supercharging efficiency. (Intake
air passing through the turbocharger gets
very warm, which could result in lower
supercharging efficiency.) To prevent
damage to this important system, avoid
placing tools and other objects on
the intercooler.
5. Engine Oil Level Gauge Check the engine oil level at each fuel
stop. Pull out the dipstick, wipe it clean,
and insert it again. Pull it out and check
the oil level. If it’s below the lower level,
add oil to bring the level up to the
upper level. (Use only engine oil of the
recommended grade and viscosity.
Please refer to your Owner’s Manual
for oil recommendations and other
important details.) 6. Engine Coolant Reservoir
Check your coolant level at each
fuel stop. Observe the coolant
level on the outside of the reservoir
while the engine is cool. If the level
J T D M P T F U P o P S M P X F S U I B O o U I F
i - 0 8 w M F W F M N B S L
B E E D P P M B O U U P
U I F i ' 6 - - w M F W F M N B S L * G U I F S F T F S W F
tank is empty, remove the radiator
cap and refill as required. Please
refer to your Owner’s Manual for
details.
7. Engine Oil Filler Cap Change your oil according to
the maintenance schedule in
Z P V S i 8 B S S B O U Z B O E . B J O U F O B O D F
# P P L M F U w : P V S F O H J O F P J M N V T U C F
changed more frequently when you
drive on dusty roads, frequently
make short trips, or when you drive
in extremely cold weather.
8. Brake Fluid Reservoir Check your brake fluid level
monthly. Observe the fluid level on
the outside of the reservoir. If the
M F W F M J T C F M P X U I F i . * / w M F W F M N B S L
add the recommended brake fluid
' . 7 4 4 / P
G S F T I % 0 5 P S
C S B L F þ V J E
U P U I F i . " 9 w M F W F M
mark. Use only brake fluid from
a sealed container.
9. Battery When your vehicle does not start
due to a battery that has run down,
the vehicle may be jump-started by
connecting your battery to another
battery with jumper cables. Jump-starting is dangerous if
done incorrectly. Please refer
to your Owner’s Manual for
instructions. If you’re unsure about
how to jump-start your vehicle,
please consult a competent
mechanic.
10. Windshield Washer Tank It’s a good idea to check your washer fluid every time you stop
for fuel. If the level is low, fill the
windshield washer tank to the
neck of the reservoir with
windshield washer fluid. In cold
weather, use a freeze resistant
windshield washer fluid.
11. Main Fuse Box Your Impreza WRX STI has two fuse boxes. One is located under
the instrument panel, behind
the fuse box cover on the driver’s
seat side. The other is housed
in your engine compartment, as
shown here. Fuses are designed
to melt during an overload
situation in order to prevent
damage to the wiring harness and
electrical equipment. If any lights,
accessories or electrical controls
fail to operate properly, inspect
the corresponding fuse. If it has
blown, replace it in accordance
with the instructions in your
Owner’s Manual. The fuse puller
and spare fuses are located in
the main fuse box in the
engine compartment.
11
9
3
8
5
7
10
2
4
6
29
GetGttintigStartedInsItrument PanelGauGgesPerPsonalilizeConCtrotlslWhile OperatingSafSfetyt / /In ICasCeof EmergencyAddAdditiiional lInformation
While
Operating
Page 182 of 463
Black plate (136,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
3-18
Instruments and controls
steadily after blinking for approxi-
mately one minute. This indicates
the TPMS is unable to monitor all
four road wheels. Contact your
SUBARU dealer as soon as possible
for tire and sensor replacement and/
or system resetting.
If the light illuminates steadily after
blinking for approximately one min-
ute, promptly contact a SUBARU
dealer to have the system inspected.
CAUTION
The tire pressure monitoring system
is NOT a substitute for manually
checking tire pressure. The tire
pressure should be checked peri-
odically (at least monthly) using a
tire gauge. After any change to tire
pressure(s), the tire pressure mon-
itoring system will not re-check tire
inflation pressures until the vehicle
is first driven more than 20 mph (32
km/h). After adjusting the tire pres-
sures, increase the vehicle speed to
at least 20 mph (32 km/h) to start the
TPMS re-checking of the tire infla-
tion pressures. If the tire pressures
are now above the severe low
pressure threshold, the low tire
pressure warning light should turn off a few minutes later. Therefore, be
sure to install the specified size for
the front and rear tires.
&
ABS warning light
CAUTION
.
If any of the following conditions
occur, we recommend that you
have the ABS system repaired at
the first available opportunity by
your SUBARU dealer.
– The warning light does not
illuminate when the ignition
switch is turned to the “ON ”
position.
– The warning light illuminates
when the ignition switch is
turned to the “ON ”position,
but it does not turn off even
when the vehicle speed ex-
ceeds approximately 8 mph
(12 km/h).
– The warning light illuminates
during driving.
. When the warning light is on (and
the brake system warning light is
off), the ABS function shuts
down. However, the conventional
brake system continues to oper- ate normally.
With a vehicle equipped with an EBD
system, the ABS warning light illuminates
together with the brake system warning
light if the EBD system malfunctions. For
further details of the EBD system mal-
function warning, refer to “Electronic
Brake Force Distribution (EBD) system
warning ”F 3-19.
NOTEIf the warning light behavior is as
described in the following conditions,
the ABS system may be considered
normal.
. The warning light illuminates right
after the engine is started but turns off
immediately, remaining off.
. The warning light remains illumi-
nated after the engine has been started,
but it turns off when the vehicle speed
reaches approximately 8 mph (12
km/h).
. The warning light illuminates during
driving, but it turns off immediately and
remains off.
When driving with an insufficient battery
voltage such as when the engine is jump
started, the ABS warning light may illumi-
nate. This is due to the low battery voltage
and does not indicate a malfunction.
Page 336 of 463
Black plate (298,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
8-6
Driving tips
Winter driving& Operation during cold
weatherCarry some emergency equipment, such
as a window scraper, a bag of sand,
flares, a small shovel and jumper cables.
Check the battery and cables. Cold
temperatures reduce battery capacity.
The battery must be in good condition to
provide enough power for cold winter
starts.
It normally takes longer to start the engine
in very cold weather conditions. Use an
engine oil of a proper grade and viscosity
for cold weather. Using heavy summer oil
will make it harder to start the engine.
Keep the door locks from freezing by squirting them with deicer or glycerin.
Forcing a frozen door open may damage
or separate the rubber weather strips
around the door. If the door is frozen,
use hot water to melt the ice, and after-
wards thoroughly wipe the water away.
Use a windshield washer fluid that con-
tains an antifreeze solution. Do not use
engine antifreeze or other substitutes
because they may damage the paint of
the vehicle.
SUBARU Windshield Washer Fluid con-
tains 58.5% methyl alcohol and 41.5%
surfactant, by volume. Its freezing tem-
perature varies according to how much it
is diluted, as indicated in the following
table.
Washer Fluid Con-
centration Freezing Temperature
30% 10.4 8F( 12 8C)
50% 48F( 20 8C)
100% 49
8F( 45 8C)In order to prevent freezing of washer
fluid, check the freezing temperatures in
the table above when adjusting the fluid
concentration to the outside temperature.
If you fill the reservoir tank with a fluid with
a different concentration from the one used previously, purge the old fluid from
the piping between the reservoir tank and
washer nozzles by operating the washer
for a certain period of time. Otherwise, if
the concentration of the fluid remaining in
the piping is too low for the outside
temperature, it may freeze and block the
nozzles.
CAUTION
.
Adjust the washer fluid concen-
tration appropriately for the out-
side temperature. If the concen-
tration is inappropriate, sprayed
washer fluid may freeze on the
windshield and obstruct your
view, and the fluid may freeze in
the reservoir tank.
. State or local regulations on
volatile organic compounds may
restrict the use of methanol, a
common windshield washer anti-
freeze additive. Washer fluids
containing non-methanol anti-
freeze agents should be used
only if they provide cold weather
protection without damaging
your vehicle ’s paint, wiper blades
or washer system.
Page 345 of 463
Black plate (17,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 2
If you park your vehicle in case of an
emergency ........................................................ 9-2
Temporary spare tire ........................................... 9-2
Maintenance tools ............................................... 9-3
Tool bag.............................................................. 9-4
Under the rear floor ............................................. 9-4
Flat tires............................................................... 9-5
Changing a flat tire .............................................. 9-5
Tire pressure monitoring system (TPMS) (U.S.-spec. models) ........................................... 9-8
Jump starting...................................................... 9-9
How to jump start ............................................... 9-10
Engine overheating ........................................... 9-12
If steam is coming from the engine
compartment ................................................... 9-12
If no steam is coming from the engine compartment ................................................... 9-12
Towing................................................................ 9-12
Towing and tie-down hooks. ............................... 9-13
Using a flat-bed truck. ........................................ 9-15
Towing with all wheels on the ground ................. 9-15
Rear gate–if the rear gate cannot be
unlocked .......................................................... 9-16
Moonroof –if moonroof cannot be closed ...... 9-17
In case of emergency
9
Page 353 of 463
Black plate (315,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
brake suddenly and keep driving
straight ahead while gradually redu-
cing speed. Then slowly pull off the
road to a safe place. Otherwise an
accident involving serious vehicle
damage and serious personal injury
could occur.
Check the pressure for all four tires
and adjust the pressure to the COLD
tire pressure shown on the vehicle
placard on the door pillar on the
driver ’s side. If this light still illumi-
nates while driving after adjusting
the tire pressure, a tire may have
significant damage and a fast leak
that causes the tire to lose air
rapidly. If you have a flat tire, replace
it with a spare tire as soon as
possible.
When a spare tire is mounted or a
wheel rim is replaced without the
original pressure sensor/transmitter
being transferred, the low tire pres-
sure warning light will illuminate
steadily after blinking for approxi-
mately one minute. This indicates
the TPMS is unable to monitor all
four road wheels. Contact your
SUBARU dealer as soon as possible
for tire and sensor replacement and/
or system resetting.
Do not inject any tire liquid or aerosol tire sealant into the tires, as
this may cause a malfunction of the
tire pressure sensors.
If the light illuminates steadily after
blinking for approximately one min-
ute, promptly contact a SUBARU
dealer to have the system inspected.
Jump starting
WARNING
.
Battery fluid is SULFURIC ACID.
Do not let it come in contact with
the eyes, skin, clothing or the
vehicle.
If battery fluid gets on you,
thoroughly flush the exposed
area with water immediately. Get
medical help if the fluid has
entered your eyes.
If battery fluid is accidentally
swallowed, immediately drink a
large amount of milk or water,
and obtain immediate medical
help.
Keep everyone including chil-
dren away from the battery.
. The gas generated by a battery
explodes if a flame or spark is
brought near it. Do not smoke or
light a match while jump starting.
. Never attempt jump starting if the
discharged battery is frozen. It
could cause the battery to burst
or explode.
. Whenever working on or around
a battery, always wear suitable
In case of emergency
9-9
– CONTINUED –
9
Page 354 of 463
Black plate (316,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
9-10
In case of emergency
eye protectors, and remove metal
objects such as rings, bands or
other metal jewelry.
. Be sure the jumper cables and
clamps on them do not have
loose or missing insulation.
Do not jump start unless cables
in suitable condition are avail-
able.
. A running engine can be danger-
ous. Keep your fingers, hands,
clothing, hair and tools away
from the cooling fan, belts and
any other moving engine parts.
Removing rings, watches and
ties is advisable.
. Jump starting is dangerous if it
done incorrectly. If you are un-
sure about the proper procedure
for jump starting, consult a com-
petent mechanic.
When your vehicle does not start due to a
run down (discharged) battery, the vehicle
may be jump started by connecting your
battery to another battery (called the
booster battery) with jumper cables.
& How to jump start1. Make sure the booster battery is 12
volts and the negative terminal is
grounded.
2. If the booster battery is in another
vehicle, do not let the two vehicles touch.
3. Turn off all unnecessary lights and
accessories.
4. Connect the jumper cables exactly in
the sequence illustrated.
Page 355 of 463
Black plate (317,1)
北米Model "A1130BE-A" EDITED: 2011/ 6/ 7
(1) Connect one jumper cable to the
positive (+) terminal on the discharged
battery.
(2) Connect the other end of the
jumper cable to the positive (+) term-
inal of the booster battery.
(3) Connect one end of the other
cable to the negative ( ) terminal of
the booster battery.
(4) Connect the other end of the cable
to the strut mounting nut of the vehicle
with the discharged battery.
Make sure that the cables are not near
any moving parts and that the cable
clamps are not in contact with any other
metal.
5. Start the engine of the vehicle with the
booster battery and run it at moderate
speed. Then start the engine of the vehicle
that has the discharged battery.
6. When finished, carefully disconnect
the cables in exactly the reverse order.
In case of emergency
9-11
9