2012 SSANGYONG RODIUS key

10-6
2) Configuration
Test voltage(VCC 5V) ▶
FUNCTION KEY VOLUE REMARK
MAIN 0.15 ~ 0.55V -
DECEL 0.7 ~ 1.1V -
ACCEL 1.6 ~ 2.0V -
RESUME 2.52 ~ 2.92V -

10-12
Do not move the shift lever to Neutral position while driving with the cruise control turned on.
Otherwise, it may result in system malfunction or accidents.
Always be prepared to use the brake or accelerator pedal for safe driving while the cruise
control system is running.
The actual speed can be different from the set speed momentarily when driving on a uphill
or downhill. So, it is recommended to disable the cruise control function on a uphill or
downhill. hen driving on a steep hill use the engine brake and foot brake properly to protect
the vehicle system and for a safe driving.
Ensure that the safe distance is maintained and use the brake pedal if needed. 1.
2.
3.
4.
(1) Abnormal Cancellation of the Cruise Control
When the rapid deceleration is applied without braking.
When the rapid acceleration is applied without acceleration pedal intervention.
When the cruise control lever is faulty.
When the brake switch and the brake light switch input signal are implausible. 1.
2.
3.
When the cruise control function is cancelled abnormally or intermittent problems occur, stop the
vehicle and turn off the ignition switch and remove the key to reset the system. After a while, turn
on the ignition switch again to operate the cruise control system.

02-58710-01
The remote engine control function has been deleted in this model.
1. COMPONENTS
STICS / ICM module
Air bag ECU
Sends the vehicle collision
signals to STICS.
Theft deterrent horn
Installed under the battery.
This horn works only for the
theft deterrent function,
panic function, and remote
starting.
SCAN-tool
SIW is used for REKES key
coding and trouble
diagnosis.
REKES
Added the escort and
panic function
RK STICS
ICM module
This module contains
various relays, chime and
buzzer controlled by STICS

02-6
2. FUNCTIONS OF RK STICS
1) Wiper Control
(1) Wiper MIST and Washer Coupled Wiper
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for 0.2 ~
0.59 seconds (T2) with the ignition key “ON”, and it is turned off when the parking terminal is
turned off. 1.
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch over 0.6
seconds (T2) with the ignition key “ON”, and it is turned on three times immediately after
turning off the washer switch. 2.

02-98710-01
▶ Rain sensing operation point
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is
<009b009c00990095008c008b0047009b0096004702c80076007502c9004700970096009a0090009b0090009600950047004f009e008f00900093008c0047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a00
4700900095004702c80068007c007b007602c9004700970096>sition).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the
<009e00900097008c00990047009a009e0090009b008a008f0047009b0096004702c80068007c007b007602c9004700970096009a0090009b0090009600950047008d00990096009400470088009500a000470096009b008f008c0099004700970096009a00
90009b009000960095009a0047004f009e008f00900093008c> the ignition key is in “ON”
<00970096009a0090009b009000960095005000550047007e008f008c00950047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b0047009b0096004702c80068007c007b00
7602c9004700970096009a0090009b00900096009500470088>gain from other positions, the
system drives the wiper relay (LO) to run the wiper motor one cycle only when the rain sensor
detects the “Rain Detected” signal. 1)
2)

02-118710-01
The wiper system continuously outputs the parking signal of current sensitivity when the
parking terminal is grounded (while the ignition key is in “ON” position and the wiper switch is
in “AUTO” position). 1)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
When the parking terminal is fixed to IGN (HIGH), the wiper system outputs the operating
signal of current sensitivity for 2 seconds, then continuously outputs the parking signal of
current sensitivity. 2)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
▶ Wiper operation when the wiper parking terminal is grounded

02-138710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper
sensitivity is changed to 3 from 4 during receiving the malfunction signal (2) from the rain
sensor (while the ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity
is changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while
<009b008f008c00470090008e00950090009b00900096009500470092008c00a000470090009a004700900095004702c80076007502c9004700970096009a0090009b009000960095004700880095008b0047009b008f008c0047009e00900097008c009900
47009a009e0090009b008a008f00470090009a004700900095> “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)

02-178710-01
2) Ignition Key Reminder
▶Key Reminder Warning
<007b008f008c0047008a008f00900094008c00470089009c00a100a1008c009900470096009c009b0097009c009b0047009000950047009b008f008c00470070006a0074004700890096009f0047008a00960095009b00900095009c008c009a0047009e00
8f008c0095004700960097008c009500900095008e0047009b>he driver’s door while the
ignition key is inserted into ignition switch.
<007e008f008c009500470099008c00940096009d00900095008e0047009b008f008c00470090008e00950090009b00900096009500470092008c00a00047009600990047008a00930096009a00900095008e0047009b008f008c0047008b00990090009d00
8c009902c5009a0047008b0096009600990047008b009c0099>ing chime buzzer output, the
output turns off.
This function is not available when the ignition switch is “ON”. 1.
2.
3.