2012 SSANGYONG NEW REXTON ECU

Engine Compartment Layout
Engine assembly
Engine oil dipstick
Vacuum pump
Oil filter and cooler
Fuel filter and priming pump
Brake booster
Brake oil tank
AQGS unit
Washer fluid filler cap
Engine compartment fuse box
PTC relay box
Battery
Vacuum modulator (for VGT turbo charger) 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.FFH Assembly (Only for vehicle with FFH)
Power steering oil tank
Engine oil filler cap
Fan shroud
E-EGR Valve
High-capacity PCV oil separator
HFM sensor (6.0)
VGT turbo charger
Air cleaner housing
2Coolant surge tank
ABS/ESP HECU (Including TPMS function:
optional)
Exhaust gas FRT Temp. sensor (T3) 14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.

2. SYSTEMS IN ENGINE COMPARTMENT
1) Engine Accessories Related to ECU

1881-09
3) Fuel Rail - Chrome Color
D27DTP & D27DT (EU IV)
Common rail)
D27DT
Common rail)The I.D and O.D of the fuel rail between
HP pump and common rail are increased
according to the increased amount of fuel
injection.
Also, the engine ECU, HFM sensor and
EGR system are changed to control the
fuel injection volume and engine more
precisely.

1792-01
1. COMPONENTS
The components of the exhaust system for the D27DTP (POWER UP) engine have been changed
as follows:
1. E-EGR valve: Controlling the EGR valve electrically and sends the valve location signal to
ECU (vacuum modulator control has been deleted)
2. EGR cooler: Decreasing EGR gas (NOx) efficiently by cooling the EGR gas and let it flow to
the intake pipe
3. VGT turbocharger: Increase in capacity and performance compared to D27DTP & D20DT
engine
The EGR system has been changed to control NOx more efficiently and the VGT turbo charger
has been changed to increase the engine power. For more details, refer to the next description.
The exhaust system for D27DTP (POWER UP) engine is as follows:

1725-12
1. OVERVIEW FOR CDPF (EURO IV)
1) General Description
The CDPF (Catalyst & Diesel Particulate Filter) was installed to the Rexton II D27DTP engine
previously. However, it is now installed to the all 2009 DI engine models, except the
Actyon
Sports. The DI engine types installed to Rexton are D27DTP, D27DT and D20DT, and their CDPF,
related sensor and operation logic are the same.
This section describes the CDPF system (based on Euro IV) which is installed to the Rexton II
D27DTP engine (older model).
2) Compatibility of CDPF System by Vehicle Model
Rexton II: Same CDPF system for D27DTP and D27DT engines (including its components)
Kyron & Actyon: Same CDPF system for D27DT and D20DT engines (including its components)
The CDPF assemblies installed to the Euro IV D27DTP Rexton II and 2009 Rexton II are
different in their mounting layout, but their front/rear exhaust temperature sensors and
differential pressure sensors are same. -
3) System Met with Euro IV Regulations
E-EGR valve
EGR cooler
Engine ECU (Ver. 3.2)
HFM sensor
C3I injector
Electronic throttle valve (body)
Other engine mounting components -
-
-
-
-
-
-
For details about the modified components and system related to the Euro IV regulations, refer to
the 2008 Rodius engine service manual.

1725-12
Throttle Body
CDPF system controls the amount of intake air by
controlling the electronic throttle body. The electronic
throttle body has the following main functions.
CDPF control - added a function that increases the
exhaust gas temperature by closing the throttle valve
flap to minimize the intake air amount by the fuel
injection amount during the CDPF regeneration range
with the low engine load range.
ON/OFF control - prevents the engine from turning off
with vibration and noise by closing the throttle body flap
to block the intake air when the engine is stopped.
Duty control - controls the valve inside the throttle body
to burn more EGR gas in the EGR valve operating range.
VGT Turbocharger and Front Exhaust Gas Temperature Sensor
Front exhaust gas
temperature sensorTurbocharger may become weaker if high
temperature exhaust gas passes through the
turbocharger for DPF regeneration process.
The front exhaust gas temperature sensor monitors
the temperature of the exhaust gas that flows into
the turbocharger.
If the temperature of the exhaust gas that passes
through the exhaust manifold is higher than the
specification, the ECU decreases the fuel injection
amount and increases the EGR gas intake amount
to decrease the exhaust gas temperature.

1725-12
2. CDPF (EURO IV) SYSTEM CONTROL
1) Combustion Temperature and Procedures
As the soot is filtered in the CDPF, it is burnt and removed, and the CDPF is returned to the initial
state to collect the soot. Therefore, the burning procedures in the CDPF can be called as
regeneration.
The CDPF assembly is integrated with DOC (at front side) and DPF (at rear side).
The DPF burns the soot with high-temperature exhaust gas (over
The rear exhaust gas
temperature sensor monitors the temperature of DPF section. If this temperature is below the
regeneration temperature, the ECU increases the post injection period to increase the fuel
injection amount, and consequently to increase the exhaust gas temperature.
Front exhaust gas temperature sensor
(Measuring temperature of exhaust gas in
exhaust manifold)
Rear exhaust gas temperature sensor
(Measuring temperature of exhaust gas escaping DOC)
Normally, when the vehicle is driven for 600 ~ 1,200 km, the enough amount of soot to be
burnt is filtered and accumulated in the CDPF. The ECU increase the amount of post
injection to increase the tempeature of exhaust gas up to
so that the soot is burnt.
The soot is burnt for 15 ~ 20 minutes. -

1725-12
Throttle bodies by engine type
The throttle valve is controlled by electric signals sent from the engine ECU for optimal
fuel injection volume, engine load and effective combustion of EGR gas according to
the Euro 4 regulations. It has following functions by the engine type. -