2012 SSANGYONG KORANDO stop start

01-8
Steering wheel remote
control switchPassenger door switch
Lower main panel
switch
Start/stop switch
Cruise control switch
Hazard warning switch
bezel assembly
Multifunction switch
FATC switch
Drive door main switch
& Outside rearview mirror
switch
3. SWITCH SYSTEM LAYOUT

03-10
1) Wiper Control
(1) Wiper mist & front washer coupled wiper
Wiper mist ▶
When the multi-function switch is rotated for more than 0.1 second to activate the mist mode with
IGN1 ON, the wiper relay is activated after 0.1 second. It will be deactivated when the wiper motor
is in the parking position.
While the wiper operates at high speed when the mist switch signal is received, it operates at low
speed if the switch is returned to its starting position. 1.
2.
Front washer coupled wiper ▶
When holding the front washer switch at ON position for more than 0.6 seconds with IGN ON, the
wiper relay is activated 0.5 seconds after. The wiper stops after three more wipes since that the
washer switch is turned to "OFF" position. 1.

03-12
Auto washer coupled wiper ▶
When turning ON the auto washer switch with IGN ON and intermittent/automatic wiper switch OFF,
the washer fluid is sprayed onto the windshield glass for 2 seconds and the wipers operate 4 times.
After then, additionally, the washer fluid is sprayed for 1.5 seconds and the wipers operate 3 times
again.
The auto washer switch signal is overridden during speed sensitive intermittent wiper, washer
coupled wiper or auto washer coupled wiper operation.
When turning the wiper switch to AUTO position during the operation of auto washer, the auto
washer stops its operation and the intermittent/automatic wiping mode will be started.
The front and rear washer switch signal are overridden during the operation of auto washer. 1.
2.
3.
4.

03-28
Seat belt reminder ▶
Operating conditions for seat belt reminder are as follows: IGN ON, engine running (over 300 rpm),
vehicle speed of 25 km/h or higher, driver seat belt unfastened, passenger seat belt unfastened and
passenger seat occupied. In addition, if the seat belt reminder is activated at the speed of 25 km/h or
higher and the speed reduces to below 25 km/h within 5 minutes, the interior buzzer sound stops. The
buzzer sounds for 5 minutes again when the speed is 25 km/h or higher.
The seat belt reminder stops its operation when fastening the seat belt, but starts the operation again if
unfastening the seat belt.
If the seat belt reminder is initially operated due to unfastened driver seat belt, the buzzer sounds with
the interval of 0.02s ON/1.18s OFF, the instrument cluster sends the driver seat belt warning signal
(SBR) and the seat belt warning lamp stays on.
At this time, the buzzer sounds for 5 minutes.
If the seat belt reminder is operated due to unfastened passenger seat belt when the passenger seat
belt reminder sensor detects that the passenger seat is occupied, the instrument cluster sends the
driver seat belt warning signal and the seat belt warning lamp stays on.
For this case, the indicator shows each status of the driver and passenger seats but the indoor buzzer
is common to both seats.
If the simultaneous operating condition for the indoor buzzer is met, the driver seat has the priority.
If the driver seat belt is fastened, the same operation is also carried out in the passenger seat
automatically.
The buzzer and the warning lamp are operated according to the vehicle speed as below table during
the seat belt reminder operation. 1.
2.
3.
4.
5.
Seat belt reminder operation
<007700990090009600990090009b00a000470096008d00470089009c00a100a1008c0099004700960097008c00990088009b00900096009500610047007a0069007900470d7d00470072008c00a000470099008c009400900095008b008c00990047009e00
880099009500900095008e00470d7d0047007a009c00950099>oof warning ⇒ Tail lamp ON
<009e00880099009500900095008e00470d7d0047006f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c009900470d7d0047007b009c009900950047009a0090008e009500880093004700930088009400
970055> 6.
Buzzer Warning lamp
25 Km/h ~ 49 Km/h 0.02s ON / 1.18s OFF Keep ON
50 Km/h ~ 99 Km/h 0.02s ON / 0.98s OFF Keep ON
10 Km/h ~ 49 Km/h 0.02s ON / 0.78s OFF Keep ONFunction
Vehicle speed
Seat belt remind warning lamp (EU only)
This lamp comes on for 6 seconds after turning on the ignition switch. If the vehicle speed goes
over 10 km/h without fastened the seat belt, the inside buzzer sounds. -

03-458710-01
12) Panic Alarm
Panic alarm by REKES signal ▶
When receiving the panic signal with Power OFF, ACC and IGN ON, the horn and turn signal lamps
operate for T1 with the interval of 0.5s ON/0.5s OFF.
When receiving the door lock or panic signal during the panic operation, the panic alarm stops.
(other commands are overridden)
The theft deterrent functions are as below:
- The theft deterrent alarm stops when receiving the panic alarm during its operation.
- The panic alarm stops and then the theft deterrent alarm starts its operation when occurring the
theft deterrent alarm conditions during panic alarm.
This function should be available regardless of the key status.
This function should be activated only when the ignition key is inserted (EU region). 1.
2.
3.
4.
5.

03-46
Panic alarm by SKM smart key's remote control ▶
When the BCM receives "Panic command by smart key remote control" as a BCAN signal, it
activates panic alarm by operating the horn and turn signal lamp for 30 seconds with a interval of
0.5s ON/0.5s OFF. However, the BCM used in EU region is operated when receiving the panic
command from the smart key remote control and the signal that the smart key is in the vehicle with
Power OFF, ACC and IGN ON.
The BCM stops the panic function and operates the function depending on the signal in the event of
following commands during turn signal lamp and horn operation by the "Panic command from smart
key remote control".
The panic alarm stops and then the theft deterrent alarm starts its operation when occurring the theft
deterrent alarm conditions during panic alarm.
All the functions are controlled by SKM and operated by signal from SKM. 1.
2.
3.
4.
Stops panic function activated by "Panic command from smart key remote control" through
BCAN signal
Panic function is activated when receiving other command -
-

03-578710-01
18) Flasher (Blinking) Function
Turn signal lamp control ▶
When the BCM is received the multifunction switch signal, it operates the turn signal lamp
and interior buzzer with the intervals of 400 ms ON/400 ms OFF for 75 times/min.
The turn signal lamps are operational only when IGN1 is ON.
If the turn signal lamp is defective during its operation, the turn signal lamp blinks with the intervals of
300 ms ON/300 ms OFF for 100/min and the interior buzzer sounds with same interval.
Defective conditions by BCM: Open - below load of 3.0 A, Short - over load of 7.0 A (load means lamp
load here)
When turning ON the turn signal switch, the lamp blinks 3 times by the BCM. When turning OFF the
switch during the operation, the turn signal lamp blinks 3 times and goes off.
When turning OFF and then immediately ON the turn signal switch during auto blinking operation of 3
times, the turn signal lamp blinks additional 3 times.
When turning ON another turn signal switch during the operation, currently operated turn signal lamp
stops immediately and another turn signal lamp starts blinking. 1.
2.
3.
4.
5.
6.
7.

03-58
Right turn signal lamp control ▶
When the BCM is received the multifunction right turn signal lamp switch signal, it operates the right
turn signal lamp and interior buzzer with the intervals of 400 ms ON/400 ms OFF for 75 times/min.
When turning OFF the right turn signal switch during its operation, the turn signal lamp and buzzer
stop the operation.
The turn signal lamps are operational only when IGN1 is ON.
If the turn signal lamp is defective during its operation, the turn signal lamp blinks with the intervals of
300 ms ON/300 ms OFF for 100/min and the interior buzzer sounds with same interval.
Defective conditions by BCM: Open - below load of 3.0 A, Short - over load of 7.0 A (load means lamp
load here)
When turning ON the turn signal switch, the lamp blinks 3 times by the BCM. When turning OFF the
switch during the operation, the turn signal lamp blinks 3 times and goes off.
When turning OFF and then immediately ON the turn signal switch during auto blinking operation of 3
times, the turn signal lamp blinks additional 3 times.
When turning ON the left turn signal switch during the right turn signal lamp operation, the right turn
signal lamp stops immediately and the left turn signal lamp starts blinking. 1.
2.
3.
4.
5.
6.
7.