2012 SSANGYONG KORANDO position light

03-56
16) Time Lag Power Window Control
When turning the ignition switch to ON position, the power window relay is turned ON.
The power window relay keeps ON for 30 seconds even when stopping the engine.
However, the power window relay is turned OFF when opening a front door.
When locking the door (activation of theft deterrent mode), the power window relay is
immediately turned OFF. 1.
2.
3.
17) Sleep Mode
If the driver door/passenger door/rear doors/tailgate lock switch is not changed for 6 seconds with all
driver door/passenger door/rear doors/tailgate closed, key removed, IGN1 and IGN2 OFF, the
vehicle enters into sleep mode for system power down.
If any of conditions in Step (1) is not satisfied, the System Wake-up mode is activated.
When output such as room lamp, key hole illumination, tail lamps and power window is activating or
all the doors keep closed for 30 seconds after door is unlocked for conditions in Step (1), the system
is in normal mode. Then, if there is no change within 6 seconds with all output conditions and ready
conditions released and all the doors closed, the sleep mode is activated.
When turning on the overhead room lamp switch, the overhead room lamps come on for 10 minutes
and go off, and the sleep mode is activated after 6 seconds.
When the coming home light OFF conditions are satisfied, the sleep mode is activated.
In this condition, when opening a door or inserting the ignition key into key hole, the sleep mode is
deactivated. 1.
2.
3.
4.
5.
6.

03-638710-01
19) DRL (Daytime Running Light) Control
When receiving the DRL activation signal, the tail lamps are turned ON when turning the ignition
switch to ON position, and the headlamps are turned ON when the engine speed is 300 rpm or
higher.
When turning ON the tail lamp switch during engine running, the headlamps are turned OFF.
The headlamps do not come ON when the engine speed is above 300 rpm with the tail lamp switch
ON.
The auto light sensor is not available in the vehicle with DRL system.
If there is no DRL activation signal, the light system operates in normal conditions. 1.
2.
3.
4.
5.
20) Fog Lamp Control
When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog lamps
are turned ON. When pressing the rear fog lamp switch again during the operation, the rear fog lamps
are turned OFF.
The rear fog lamps do not come ON when the IGN2 switch is turned to OFF position or the light
switch is OFF.
The rear fog lamps should not automatically come on again if they have been turned OFF by any
other way other than the switch. 1.
2.
3.
(The rear fog lamps are applied to only EU region)

03-64
21) Auto Light Control (LIN)
The BCM communicates with the auto light sensor when turning the ignition switch to ON position, and
controls the tail lamps and the headlamps depending on the LIN data with the light switch AUTO. 1.

03-698710-01
3) Operation of Immobilizer
When the ignition switch is turned to the ON position with REKES key, the BCM checks the crypto code
of the inserted key using the immobilizer antenna and sends whether the engine is startable or not to the
engine ECU through the CAN communication so that the engine can be started.
BCM
REKES key
Immobilizer antenna
ECUCAN line
For the vehicle with the immobilizer, there can be a problem in starting the vehicle or the system error:
When two or more immobilizer keys come into contact with (each) other(s).
When the key is close to any device sending or receiving electromagnetic fields or waves other
than Ssangyong products.
When the key is close to any electronic or electric devices such as lighting equipment, security keys
or security cards.
When the key is close to a magnetic or metal object or a battery. -
-
-
-

05-118010-01
Indicator
(green)
Headlamp high beam indicator ▶
Front fog lamp indicator ▶
Side light indicator ▶
Indicator
(blue)
Indicator
(green)
Indicator
(amber)
Glow indicator(DSL only) ▶
Indicator
(red)
Fuel filter indicator(DSL only) ▶This indicator comes on when the tail lamp is switched on.
This indicator comes on when the ignition switch is turned to the "ON"
position and will go off when the glow plugs are sufficiently heated.
This indicator comes on when the water level in the fuel filter exceeds a
certain level. This lamp comes on when the headlamp high beam is operated.
This indicator comes on when the fog lamp switch is operated after the tail
lamps comes on.
3) Details of Warning Lamps and Indicators

05-16
Indicator
(green)
Passenger seat belt reminder ▶
Left turn signal indicator ▶
Right turn signal indicator ▶
Indicator
(red)
Indicator
(green)
Indicator
(red)
Winter mode indicator(DSL only) ▶The right turn signal indicator blinks if the light switch is pushed up to the right,
and both turn signal indicators blink if the hazard warning flasher switch is
pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp ▶
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

05-258010-01
Operations for power supply in SVC ▶
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated in
advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
5) Illumination & Brightness
(1) Operations for Power Supply

06-32
Light switch ▶
Headlamps ON
Headlamp, side-marker, tail,
license plate, fog, and
instrument cluster lamps come
on.
Tail lamp ON
Side-marker, tail, license plate,
fog, and instrument cluster
lamps come on.
Automatic light ON
Head- and tail lamps
automatically turn on or off based
upon the intensity of the sunlight
analyzed by the automatic light
sensor.Lights OFF
High beam ON
To turn on the headlamp high
beam, push the lever towards
the instrument cluster with the
headlamp low beam on.Right turn signal lamp blinks
Passing
Regardless of the position of the light
switch, when holding the lever toward
the steering wheel, the headlights are
on high beam during the hold.Front fog lamp switch
To turn on the fog lights, turn this
switch while the tail lamps or
headlamps are turned on. Left turn signal lamp blinks