2012 SSANGYONG KORANDO ignition

04-26
7) START Switch Control
Status Turning on conditions
OFF IGN OFF, IGN ON & engine ON
Green Engine can be started by START switch operation/Engine is cranking (IGN OFF &
brake switch ON, ACC ON & brake switch ON, IGN ON & brake switch ON, etc.)
Yellow ACC ON
Red IGN ON & engine OFF or error
Ignition status indicator on START switch ▶
(1) START switch indicator
START switch indicator output ▶
* When an error occurs, the indicator is illuminated for 0.5 sec. and goes off for 0.5 sec., and
then flashes for 10 sec.
* When all the doors are closed with B+, the LED does not flash.
Start switch indicator control ▶
Door coupled function -
1. When the driver's door is opened, the switch indicator comes on (the indicator remains on
while the door is open).
2. The indicator goes off immediately when the interior lamps are turned off.
3. The indicator goes off after the driver's door is closed and 10 sec. ON timer is activated.
4. The indicator is reset when the driver's door is opened.
Tail lamp coupled function -
Ignition
statusPower OFF
ACC ON IGN ON
(STOP)IGN ON
START ErrorRemark
Door
CloseDoor
Open
Indica-
tion
Indicator
statusOFF OFF Orange Red OFF Green Red
OFF OFF ON ON OFF ON Flashing
Illumina-
tionOFF TIME
Controlled by SKMLED
Engine START/STOP

04-298712-03
(4) Smart key battery discharge warning (3) Smart key verification fail warning
When the verification is requested for ignition status change or engine starting and no verified smart key
is in the vehicle, the SKM sends the [smart key verification status] signal, which indicates that the
verification has failed, for up to 10 sec. until the verification fail conditions are deactivated.
Verification fail detection and transmission conditions ▶
When the ignition status is changed after a smart key is verified by the START switch ON input, the
SKM sends the verification status for 10 sec. -Normally, the smart key verification warning is one of the smart key fail conditions. -
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies a smart key and sends the verification status for
another 10 sec.
When the ignition status is changed by the transponder verification while the smart key status is sent
through the BCAN, the SKM sends the smart key verification signal and also sends the transponder
verification signal for 10 sec. -
-
If low smart key battery is detected during the verification process for ignition status change or engine
start, the SKM sends the signal for [smart key battery low voltage warning] to the BCM and instrument
cluster through the BCAN for up to 10 sec. until the warning condition is deactivated.
Smart key battery discharge confirmation and deactivation ▶
If the smart key battery low voltage is confirmed, the SKM sends the smart key battery low voltage
warning signal.
If the smart key battery is in normal condition, the SKM sends the smart key battery low voltage
warning deactivation signal.
The smart key is the last used key. -
-
*
(5) Transponder verification fail warning
If a verified smart key is not found by the key verification process, the SKM sends the information that
indicates the key is not verified to the instrument cluster through the BCAN for up to 10 sec. until the
verification fail condition is deactivated.
The SKM sends the transponder verification warning when the verification has failed with the smart key
inserted into the immobilizer holder. -
Transponder verification fail detection and transmission conditions ▶
When the ignition status is changed after the transponder is verified by the START switch ON input,
the SKM sends the transponder verification status for 10 sec. -

04-30
Ignition status change
(OFF ->ACC) / (OFF ->IGN)/(ACC ->IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies the transponder and sends the verification
status for another 10 sec.
When the ignition status is changed by a smart key verification while the transponder verification is
processed, the SKM sends the signal for [transponder verification fail], and sends the smart key
verification status for 10 sec. -
-
(6) Transmission position warning
When the gear selector lever is in a position other than P or N with IGN ON and engine started, the
SKM sends the [gear position warning] signal to the instrument cluster through the BCAN for up to 10
sec. until the operating conditions are deactivated.
Transmission position warning deactivation ▶
When re-attempting to start with IGN1 ON and transmission in P or N -
(7) SKM error alert
The SKM sends the SKM error alert signal to the instrument cluster through the BCAN for up to 10 sec.
when an in ignition status related error or passive entry system error occurs.
SKM error transmission conditions ▶
When any of the following errors is detected and a DTC is set, the SKM sends the error alert signal for
10 sec.
B+ (power) low voltage
B+ (logic) low voltage
ACC ON fail
ACC OFF fail
IGN1 ON fail
IGN1 OFF fail
IGN2 ON fail
IGN2 OFF fail
Short circuit in START switch 1.
2.
3.
4.
5.
6.
7.
8.
9.
The SKM sends the corresponding signal only once for 10 sec. when any of the above errors is detected
with IGN OFF/ON. It sends the signal again when a new error occurs.

04-318712-03
(8) Brake not working alert
The SKM sends the brake not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF) while the brake is not operated.
when the brake pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(9) Clutch not working alert
The SKM sends the clutch not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF)
while the clutch is not operated.
when the clutch pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(10) Smart key slot detection alert
The SKM sends the smart key slot detection alert signal for 10 sec. when a smart key inserted into
the slot is detected with IGN OFF and the driver's door open. -
(11) SKM alert priority
1 Smart key out alert EXTERIOR
1
2 Smart key reminder alert EXTERIOR
3 Smart key verification fail alert INTERIOR
2 4 Transponder verification failure alarm INTERIOR
5 Smart key battery low voltage alert INTERIOR
6 Transmission position alert INTERIOR
7 SKM error alert INTERIOR
8 Brake alert INTERIOR
9 Clutch alert INTERIOR
10 Smart key slot reminder alert INTERIOR1
Warning cancellation requirements ▶
Warning cancellation requirements ▶
Warning transmission conditions ▶
Warning cancellation requirements ▶
when the smart key is removed, the alert deactivation signal is sent.
when the 10 min. timer is terminated -
-

05-4
2. MAJOR CHANGES
SVC class
Previous Current
Rearranged pre-warning indicator which comes on and goes off when turning ignition on.
1) Steering wheel heating indicator added
2) Pre-warning indicator rearranged
3) Winter mode indicator added(DSL only)
STD class
Previous Current
Winter mode indicator added (one green LED)
SVC class
Previous Current
One indicator added since steering wheel heating function is equipped.

05-118010-01
Indicator
(green)
Headlamp high beam indicator ▶
Front fog lamp indicator ▶
Side light indicator ▶
Indicator
(blue)
Indicator
(green)
Indicator
(amber)
Glow indicator(DSL only) ▶
Indicator
(red)
Fuel filter indicator(DSL only) ▶This indicator comes on when the tail lamp is switched on.
This indicator comes on when the ignition switch is turned to the "ON"
position and will go off when the glow plugs are sufficiently heated.
This indicator comes on when the water level in the fuel filter exceeds a
certain level. This lamp comes on when the headlamp high beam is operated.
This indicator comes on when the fog lamp switch is operated after the tail
lamps comes on.
3) Details of Warning Lamps and Indicators

05-12
Low fuel level warning lamp ▶
Warning lamp
(amber)
Engine overheat warning lamp ▶
Warning lamp
(red)
Door ajar ▶
Warning lamp
(red)
Seat belt reminder ▶
Warning lamp
(red)
Air bag ▶
Warning lamp
(red)
This lamp comes on if the fuel level is approx. 10 ℓ or below.
However, the fuel level may change slight depending on vehicle
condition, inclination of the road, etc. Also, it blinks if there is a short or
open circuit between the fuel level sensor and cluster.
<007e008f008c00950047009b008f008c0047008a00960096009300880095009b0047009b008c00940097008c00990088009b009c0099008c00470090009a0047005800590057020b006a0047009600990047008f0090008e008f008c009900530047009b00
8f0090009a0047009300880094009700470089009300900095>ks at an
interval of 1 second, a message is displayed, the warning sounds once
through the speaker and the buzzer sounds at an interval of 0.5 seconds.
This lamp comes on when any door is open or not closed completely.
(both STD and SVC class)
This lamp comes on when the ignition switch is pressed ON.
It keeps coming on if the driver's seat belt is not fastened.
This lamp comes on when the ignition switch is pressed to the ON mode.
Then, it goes off if the system is normal.
If this lamp stays on while driving, it means that the air bag system is faulty.

05-138010-01
Indicator
(amber)
ESP ▶
ESP OFF indicator ▶
Engine check warning lamp ▶
Indicator
(amber)
Indicator
(amber)
Indicator (red)
Battery charge warning lamp ▶
Indicator (red)
Engine oil level warning lamp ▶This lamp comes on if any sensor or device related to the engine control is
defective.
This lamp comes on when the start switch is ON or when the battery level is
low.
(For EEM, warning lamp is controlled according to CAN signal)
This lamp comes on when the ignition switch is turned to "ON" position,
and then goes off if the engine oil level is normal.
If the engine oil level warning lamp comes on while driving, check the
engine oil level and oil leakage. -
- This indicator comes on when the ESP system is faulty.
This indicator comes on when pressing the ESP OFF switch.