
WARNING (Continued)
■ If the wheel has to be changed on a slope, first of all block the opposite
wheel with a stone or similar object to prevent the vehicle from unexpectedly
rolling away.
■ If the vehicle is subsequently fitted with tyres which are different to those it
was fitted with at the works, follow these guidelines »
page 189, New wheels
and tyres.
■ Always raise the vehicle with the doors closed.
■ Never position any body parts, such as arms or legs under the vehicle, while
the vehicle is raised with a lifting jack. ■ Secure the base plate of the lifting jack with suitable means to prevent pos-
sible moving. A soft and slippery ground under the base plate may move the
lifting jack, causing the vehicle to fall down. It is therefore always necessary to
place the lifting jack on a solid surface or use a wide and stable base. Use a
non-slip base (e.g. a rubber foot mat) if the surface is smooth, such as cobbled
stones, tiled floor, etc.
■ Never start the engine with the vehicle sitting on the raised jack - danger of
suffering injury.
■ Only attach the lifting jack to the attachment points provided for this pur-
pose. CAUTION
■ The prescribed tightening torque of the wheel bolts for steel and light alloy
wheels is 120 Nm.
■ If the anti-theft wheel bolt is fastened too tightly, it can cause damage to the
anti-theft wheel bolt and adapter. Note
■ The anti-theft wheel bolt set and adapter can be purchased from a
ŠKODA Serv-
ice Partner. ■ The national legal requirements must be observed when changing a wheel. ÐPreliminary work
First read and observe the introductory information and safety warn-
ings on page 196.
The following steps must be carried out before actually changing the wheel:
ä ›
In the event of a puncture, park the vehicle as far away as possible from the
flow of traffic. The place you choose should be level.
› Let all of the occupants get out.
While changing a tyre, the occupants of the
vehicle should not stand on the road (instead they should remain behind a crash
barrier).
› Switch off the engine and move the gearshift lever into
Neutral or move the
selector lever
for the automatic gearbox into position P .
› Firmly apply the
handbrake.
› If a trailer is connected, remove it.
› Remove the vehicle tool kit
» page 196 and the spare wheel »
page 190 from
the boot. Ð Changing a wheel
First read and observe the introductory information and safety warn-
ings on page 196.
Always change a wheel on a level surface as far as possible.
›
Remove the full wheel trim
» page 191 or caps » page 191.
› In the case of light alloy wheel rims remove the wheel trim cap
» page 191.
› First of all slacken the anti-theft wheel bolt and then the other wheel
bolts » page 198.
› Jack up the vehicle until the wheel that needs changing is clear of the
ground » page 199.
› Unscrew the wheel bolts and place them on a clean surface (cloth, paper, etc.).
› Remove the wheel.
› Attach the spare wheel and slightly screw on the wheel bolts.
› Lower the vehicle.
› Alternately tighten the wheel bolts opposite each other using the wheel
wrench (crosswise) and then tighten the anti-theft wheel bolt » page 198.
› Replace the wheel trim or the caps. Note
■ All bolts must be clean and must turn easily.
■ Under no circumstances grease or oil the wheel bolts!
■ When fitting unidirectional tyres, ensure that the direction of rotation is cor-
rect »
page 190 . Ð
ä
197
Do-it-yourself

Fuses in the dash panel
Fig. 183
Fuse box cover/Schematic diagram of the fuse box
First read and observe the introductory information and safety warn-
ings on page 207.
The fuses are located on the left side of the dash panel behind a cover.
›
Remove the cover for the fuse box using a screwdriver
» Fig. 183.
› Replace the cover once the fuse has been changed.
Fuse assignment in the dash panel No. Power consumer
1 Diagnostic socket, engine control unit, fuel pump relay, fuel pump
control unit
2 Control unit for ABS, ESC, switch for the tyre control display, brake
sensor
3 Switch and airbag control unit
4 WIV, tail lights, dimming mirrors, pressure sensor, telephone preinstal-
lation
5 Control unit for headlight beam adjustment and headlight swivel, con-
trol unit for parking aid, control unit for park assist
6 Instrument cluster, control unit for electromechanical power steering,
Haldex, selector lever lock, power supply for data bus, AG
7 Valve heating, air mass meter
8 Control unit for trailer detection 9 Relay for auxiliary heating and ventilation
10 Adaptive left main headlight ä
No. Power consumer
11 Adaptive right main headlight
12 Not assigned
13 Diagnostic socket, light switch, rain sensor, clock
14 Central locking system and bonnet lid 15 Central control unit - interior lights
16 The air conditioning system 17 Not assigned
18 Phone 19 Instrument cluster, windscreen wiper lever, and turn signal lever
20 KESSY 21 KESSY ELV
22 Air blower for Climatronic
23 Front power window, central locking of the front doors
24 Selector lever lock, AG 25 Rear window heater, relay for auxiliary heating and ventilation
26 Power socket in the boot 27 Fuel pump relay, control unit for fuel pump, injection valves
28 Electric boot lid 29 AG, Haldex
30 Ventilated front seats 31 DVD pre-installation
32 Front power window, central locking system of the rear doors
33 Electric sliding/tilting roof
34 Alarm, spare horn 35 front and rear lighter
36 Headlight cleaning system 37 Heated front seats
38 Heated rear seats 39 Rear window wiper
40 Fan air-conditioning system, relay for auxiliary heating and ventilation 41 Not assigned
42 Light switch £208
Do-it-yourself

No. Power consumer
43 Control unit for trailer detection
44 Control unit for trailer detection 45 Control unit for trailer detection
46 Switch for seat heating 47 Telephone preinstallation
48 Preparation for the aftermarket radio 49 Not assigned Ð
Fuses in the engine compartment
Fig. 184
Schematic diagram of the fuse box - version A/version B Fig. 185
Cover for the fuse box in the en-
gine compartment
First read and observe the introductory information and safety warn-
ings on page 207.
ä On some vehicles, the battery cover must be removed before removing the cover
for the fuse box
» page 184.
› The cover for the fuse box is removed by pushing the circlips A
» Fig. 185
up-
wards as far as the stop. The symbol is displayed behind the clip. Now remove
the cover.
› Once the fuse has been removed, place the cover on the fuse box and push the
circlips A
back as far as the stop. The symbol is displayed behind the clip. The
cover is locked into position.
Fuse assignment in the engine compartment - version A No. Power consumer
F1 Front right main headlight, right tail light
F2 Valves for ABS
F3-4 Not assigned F5 Horn
F6-12 Not assigned F13 Control unit for automatic gearbox
F14 Not assigned F15 Coolant pump
F16 Not assigned F17 Instrument cluster, windscreen wiper lever, and turn signal lever
F18 Audio amplifier (sound system) F19 Radio
F20-22 Not assigned F23 Engine control unit
F24 Data bus control unit
F25-26 Not assigned F27 Fuel dosage valve
F28 Engine control unit F29 Main relay
F30 Auxiliary heating and ventilation control unit F31 Windscreen wipers
F32-37 Not assigned F38 Radiator fan, valvesF39 Clutch/brake pad sensor £ 209
Fuses and light bulbs

Tail lamp assembly
Fig. 189
Outer part of the tail light/Removing the internal part of the tail
light Fig. 190
Outer part of the tail light: Bulbs/Inner part of the tail light: Bulbs
First read and observe the introductory information and safety warn-
ings on page 210.
Overview of the location of the bulbs
» Fig. 190. 1
- Turn signal lights
2
- Parking lights/Brake light
3
- parking lights
4
- Reversing light
5
- Rear fog light
ä Removing and installing the outer part of the tail light
› Open the boot lid.
› Remove the plug
» Fig. 189 - and unscrew the tail light with a torx
wrench » page 196, Vehicle tool kit .
› Carefully remove the light. Do not pull the grommet with the cables out of the
bodywork.
› To re-install the tail light, first of all guide it with the support A
°» Fig. 190 to-
wards the front onto a bolt on the bodywork.
› Carefully press the tail light onto the bodywork.
› Screw the tail light into place and push in the plugs
» Fig. 189 - .
Changing bulbs in the outer part of the tail light
› To replace the bulb, turn the bulb holder
anti-clockwise up to the stop and re-
move it from the housing.
› Replace the bulb, insert the holder with the bulb into the housing and turn
in a
clockwise direction to the the stop.
Removing and installing the inner part of the tail light
› Open the boot lid.
› Remove the tail light cover on the inner side of the boot lid
» Fig. 189 - .
› Press the lug
» Fig. 189 - and remove the lamp holder from the tail light
housing.
› To re-install, insert the lamp holder into the tail light housing.
› Press the lug until it clicks into place.
› Insert the tail light cover on the inner side of the boot lid.
Changing bulbs in the inner part of the tail light
› Remove the faulty bulb 4
» Fig. 190
from the holder and insert a new bulb.
› Turn the bulb 5
in an anti-clockwise direction
up to the stop and remove. In-
sert a new bulb into the holder and turn in a clockwise direction to the the
stop. Ð
213
Fuses and light bulbs

Tail light (Combi)
Fig. 191
Installing a tail light (Combi)
First read and observe the introductory information and safety warn-
ings on page 210.
Overview of the location of the bulbs
» Fig. 191.1
- Parking light/rear fog light
2
- Reversing light
3
- Turn signal lights
4
- Parking lights/Brake light
5
- parking lights
Removing and installing the tail light
› Open the boot lid.
› Remove the plug
» Fig. 191 and unscrew the tail light with a torx
wrench » page 196, Vehicle tool kit .
› Carefully remove the light. Do not pull the grommet with the cables out of the
bodywork.
› To re-install the tail light, first of all guide it with the openings A
°
» Fig. 191 on
to the bolts on the bodywork.
› Carefully press the tail light onto the bodywork until it clicks into place.
› Screw the tail light into place and push in the plugs.
Changing bulbs 1
, 3
and 5
›
Turn the bulb holder
anti-clockwise up to the stop and remove it from the
housing.
› Remove the faulty bulb from the holder and insert a new bulb.
ä
›
Insert the holder with the new bulb into the housing and turn
in a clockwise
direction to the the stop.
Changing bulbs 2
and 4
›
Turn the bulb holder
anti-clockwise up to the stop and remove it from the
housing.
› Push in the bulb, turn
in an anti-clockwise direction up to the stop and remove.
› Insert a new bulb into the holder, push in and turn
in a clockwise direction to
the the stop.
› Insert the holder with the new bulb into the housing and turn
in a clockwise
direction
to the the stop. Ð Licence plate light
Fig. 192
Rear bumper: Licence plate light
First read and observe the introductory information and safety warn-
ings on page 210.
›
Unscrew the glass cover of the light
» Fig. 192.
› Remove the faulty bulb from the holder and insert a new one.
› Replace the glass cover and push in until the stop. Make sure that you install
the glass cover in the correct position.
› Screw the glass cover of the light into place. Ð
ä
214 Do-it-yourself

Index
A
ABS Function 111
Warning light 23
Accessories 194
Active driver-steering recommendation (DSR) 110
Adjusting Exterior mirror 64
Adjusting seats 141
Adjustment Seat 67
Aerial 168
see Radio reception 170
Airbag 148
Deployment 148
Front airbag 149
Head airbag 152
Knee airbag 150
Side airbag 151
Airbag system 148
Air conditioning system 93
Air outlet vents 94
Climatronic 97
Manual air conditioning system 94
Alarm 33
Anti-theft alarm system 33
Antilock brake system 111
Armrest Front 88
rear 72, 88
Ashtray 83
Assist systems ABS 23, 111
Cruise control systems (CCS) 116
EDL 111
ESC 22, 110Park assist 113
Parking aid 112
START/STOP 118
TCS 23, 111
Auto Check Control 18
Automatic driving lamp control 49
Automatic gearbox 121
Dynamic shift programme 124
Emergency programme 125
Information for driving 121
Kickdown 124
Manual shifting of gears on the multifunction steering wheel 123
Parking 122
Selector lever-emergency unlocking 125
Selector lever lock 124
Selector lever positions 122
Starting off 122
Stopping 122
Tiptronic 123
Automatic load deactivation 186
Auxiliary heating (auxiliary heating and ventila- tion) 100
Avoiding damage to your vehicle 162
B
Before setting off 140
Belt tensioners 147
Bonnet Closing 177
Opening 177
Warning light 21
Boot Class
N1 vehicles 73
Cover 75
Emergency unlocking 37
Emergency unlocking Combi 37
Extendable variable loading floor 77
Fastening elements 74
Fixing nets 74Fixing of the floor covering 75
foldable boot cover (Combi) 76
Folding hooks 74
Light 56
Removable lamp (Combi) 57
see Boot lid 36
Unlocking of the boot lid Combi 37
Variable loading floor 76
Boot lid 36
Automatic locking 37
Combi 37
Twindoor 36
Warning light 21
Brake assist 110
Brake booster 109
Brake fluid Checking 181
Brake pads Indicator light 25
Brakes Brake assist systems 108
Handbrake 109
Indicator light 20
Running in 158
Braking Brake fluid 181
Breakdown kit 200
Bulbs Replacing 210
Button in the driver's door Electric power windows 40
C
Car computer see Multifunction display 12
Car jack 196
Carrier 81
Catalytic converter 158
CD changer 138
Central locking button 30
225
Index

Central locking system 28
Changes 194
Changing Engine oil 179
Wheel 196
Charging a vehicle battery 185
Checking Battery electrolyte level 185
Brake fluid 181
Coolant level 180
Engine oil 178
Oil level 178
Windscreen washer fluid 182
Children and safety 154
Child safety Side airbag 155
Child safety lock 28
Child seat Classification 155
ISOFIX 156
on the front passenger seat 154
Suitability 156
TOP TETHER 156
Chrome parts refer to Taking care of your vehicle 169
Cigarette lighter 84
Cleaning 167
Artificial leather 172
Headlight lenses 170
Material coverings 172
Materials 172
Natural leather 172
Plastic parts 169
Wheels 171
Clock 11
Clothes hooks 91
Cockpit 12-volt power socket 84
Ashtray 83
Cigarette lighter 84
General view 7Light 54
Storage compartments 85
Compartments 85
Computer see Multifunction display 12
Coolant Checking 180
Replenishing 180
Temperature gauge 9
Correct seated position 141
Counter for distance driven 10
Cruise control system (CCS) 116
Cup holder front 82
rear 83
D
Daylight driving light 49
De-icing the windscreen and rear window 58
Deactivating an airbag 152
Deactivating an airbag 152
Delayed locking of the boot lid see Boot lid 37
Diesel refer to Fuel 176
Diesel fuel Operation in winter 176
Diesel particulate filter 24
Digital clock 11
Dipstick 178
Display Coolant temperature 9
Service interval 10
Distance driven 10
Door Child safety lock 28
Indicator light for an open door 20Door locking
Emergency locking 35
Doors Emergency locking 35
Driving Abroad 162
Driving through water on the street 163
Emissions 216
Fuel consumption 216
DVD-preinstallation 139
E
Economical and environmentally friendly driving 159
EDL 111
Electrical power windows Button in the driver's door 40
Electric boot lid Adjusting the lid top position 38
Malfunctions 38
Operation 38
Electric power windows Central locking system 42
Electric sliding/tilting roof 43
Electronic differential lock (EDL) 111
Electronic immobiliser 104
Emergency Automatic gearbox 125
Changing a wheel 196
Door locking 35
Hazard warning light system 53
Jump-starting 202
Locking the driver's door 35
Panoramic sliding roof (Combi) 46
Selector lever-unlocking 125
Sliding roof 44
Towing the vehicle 204
Tyre repair 200
Unlocking of the boot lid 37
Unlocking the driver's door 35
Emissions 216
226 Index

Engine
Running in 158
Starting and stopping the engine 103
Engine compartment Brake fluid 181
Coolant 179
Overview 178
Vehicle battery 182
Engine oil Changing 179
Checking 178
Replenishing 179
Engine Oil Specification 219
Engine revolutions counter 9
Environment 159
Environmental compatibility 161
Environmentally friendly driving 159
ESC Function 110
Indicator light 22
F
Fire extinguisher 195
First-aid-box 195
Footmats 112
Front airbag 149
Front seats 66
Fuel 174
Diesel 176
Fuel gauge 9
gauge 9
refer to Fuel 174
Refuelling 174
Unleaded petrol 175
Fuel consumption 159
Fuses Assignment 207
Replacing 207 G
Gear Recommended gear 11
General view Cockpit 7
Glow plug system Warning light 24
GSM 128, 131
H
Handbrake 109
Head airbag 152
Headlight cleaning system Headlight cleaning system 62
Headlights Driving abroad 162
Headlight cleaning system 62
Head restraint 70
Heating Exterior mirror 64
Seats 69
Windscreen and rear window 58
Horn 7
I
Ignition 105
Ignition lock 105
Immobiliser 104
Indicator lights 18
Information display see MAXI DOT 15
Instrument Cluster 8
See Instrument Cluster 8
Instrument lighting 53
Interior monitor 34
Internet connection 134
ISOFIX 156 J
Jacking points Raise vehicle 199
Jump-starting 202
K
KESSY see Kessy system 32
Starting 105
KESSY system Starting 105
Unlocking the vehicle 32
Knee airbag 150
L
Lever Main beam 54
Turn signal 54
Windscreen wipers 60
Light Adaptive headlights (AHL) 51
Automatic driving lamp control 49
Cockpit 54
COMING HOME/LEAVING HOME function 50
Daylight driving light 49
Fog lights 52
Fog lights with the function CORNER 52
Hazard warning light system 53
Headlight beam adjustment 53
Headlight flasher 54
Low beam 49
Main beam 54
Parking light 49, 50
Rear fog lights 52
Replacing bulbs 210
Tourist light 51
Turn signal 54
227
Index