2012 Seat Toledo technical specifications

115
Seats and storage
Rear shelf
Fig. 80 Removing the
shelf
Fig. 81 Removing the
shelf
The shelf can be removed if a large load is to be transported.
Removing the shelf
– Remove the straps from the shelf 1
⇒ Fig. 80.
– Remove the shelf from its housing 2
by knocking it gently from
underneath between the supports. Fitting the shelf
–
Place the shelf on the side supports on the trim.
– Adjust the shelf supports 3
⇒ Fig. 81 to fit the supports 2 in
the trim.
– Fit into place by knocking the top of the shelf gently between
the supports.
– Attach the straps 1
to the tray.
WARNING
Do not place objects on the rear shelf that could endanger the vehicle oc-
cupants in case of a sudden braking manoeuvre or an accident.
CAUTION
● The rear shelf supports a maximum load of 1 kg.
● If handled incorrectly, the tray could bend on closing the rear lid and be-
come damaged or damage the trim. Follow the instructions below.
–The shelf supports 3
⇒ Fig. 81 must be securely in place in the trim
supports 2.
– The size of the load must not exceed the height of the shelf.
– When open, the shelf must not be bent against the shelf seal.
– There must be no objects in the space between the open shelf and
the backrest of the rear seat.
Note
The shelf will lift when the rear lid is opened. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

117
Seats and storage
Roof load
The maximum permissible roof load (including the support system) of 75 kg
and the total authorised weight of the vehicle must not be exceeded.
It will not be possible to carry the full maximum load if the roof carrier you
are using is rated for a load which is less than this figure. In this case, you
can only load the roof carrier to the maximum load permitted in your instal-
lation manual. 
Drink holder
Introduction
WARNING
● Do not put hot drinks in the drink holders. They could spill while the
vehicle is moving. Risk of scalding!
● Do not use cups or glasses made of fragile materials (e.g. glass or chi-
na). These could cause injury in the event of an accident.
CAUTION
Avoid putting open drinks containers in the drink holder while the vehicle is
moving. They could spill (e.g. on braking) and cause damage to the electri-
cal equipment or the seat covers. Drink holder in centre console
Fig. 83 Centre console: drink holder
Front drink holder in the centre console
Rear drink holder in the centre console 
Drink holder in the rear armrest
Fig. 84 Rear seats arm-
rest: drink holder
Two drinks can be placed in the drink holder. 
A
B
Safety FirstOperating instructionsPractical TipsTechnical specifications

119
Seats and storage
WARNING
● Take care when using the cigarette lighter! Carelessness or negli-
gence when using the cigarette lighter can cause burns and serious inju-
ries.
● The cigarette lighter also works when the ignition is off and when the
ignition key is removed. Therefore, never leave children unsupervised in
the vehicle.
Note
● The 12 volt power socket of the cigarette lighter can also be used as a
power source for electrical appliances ⇒ page 119, 12 V power socket.
● Additional information ⇒ page 195, Accessories, modifications and
spare parts. 
12 V power socket
Fig. 87 Centre console:
12V power socket
The 12 V power socket is located at the front of the centre console
⇒ Fig. 87. Using the power socket
–
Open the cover or remove the cigarette lighter concealing the
socket.
– Insert the plug of the electrical appliance into the socket.
Additional information ⇒ page 195, Accessories, modifications and spare
parts.
WARNING
● Improper use of the sockets or electrical appliances can cause a fire
and lead to burns and other serious injuries.
● Never leave children unsupervised in the vehicle. The 12 volt power
socket is also operate when the is ignition switched off and the key re-
moved.
● Should the connected appliance overheat, immediately switch it off
and disconnect it from the socket.
CAUTION
● The 12V power socket can only be used to power appliances with a pow-
er rating of up to 120 Watt.
● Never exceed the maximum permitted power, as this could cause dam-
age to the vehicle electrical installation.
● When the engine is switched off, however, the vehicle battery will be
drained. Risk of flat battery!
● Only use suitable plugs so as not to damage the power socket.
● Only use appliances that have been tested for electromagnetic compati-
bility in compliance with current regulations.
● Before switching the ignition on or off, unplug the appliances from the
power socket to protect them from any damage caused by fluctuations in
voltage.
● Follow the instructions for use of connected appliances! 
Safety FirstOperating instructionsPractical TipsTechnical specifications

121
Seats and storage
– The light will go out when the glove compartment is closed.
Glove compartment cooling*
Open or close the air outlet by turning the thumbwheel ⇒ Fig. 89.
If the air outlet is open and the air conditioning is on, the cooled air will be
released into the glove compartment.
If the air outlet is open and the air conditioning is off, outdoor air (not con-
ditioned) will be released into the glove compartment.
The air outlet should be closed if the air conditioning is being used in heat-
ing mode or where glove compartment cooling is not in use.
WARNING
For safety reasons, all storage compartments must be closed while the
vehicle is moving.
Note
A maximum 1 litre bottle can be stored in the glove compartment. Compartment for reflective vest
Fig. 90 Driver seat: stor-
age
There is a compartment below the driver seat ⇒ Fig. 90 to store the reflec-
tive vests.
WARNING
The compartment is solely designed to store the reflective vest and no
other objects. Objects falling out of the storage compartment could limit
or prevent use of the pedals.
CAUTION
The compartment is solely designed to store the reflective vest and no other
objects. Risk of damage to the storage compartment. 
Storage compartments in front seats
There is a storage pocket on the rear part of the backrest of the front seats.
These pockets are designed to hold maps, magazines, etc. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

123
Seats and storage
Storage compartments in centre console
Fig. 93 Centre console:
storage
Open storage compartment in centre console ⇒ Fig. 93.
Multimedia compartment
Fig. 94 Front centre con-
sole: multimedia com-
partment
The multimedia compartment is in the storage compartment of the front
centre console ⇒ Fig. 94.
The compartment can be used to hold mobile phones, mp3 players or simi-
lar devices.
WARNING
Never use the multimedia compartment as an ashtray or to store flamma-
ble materials. Risk of fire!

Storage compartment in front door
Fig. 95 Storage com-
partment in door trim
There is a bottle carrier in part B

⇒  Fig. 95 of the storage compartment in
the front door.
WARNING
Only use part A
⇒ Fig. 95 of the compartment in the front door to store
objects that do not protrude from it so as not the limit the deployment
area of the side airbags.

Safety FirstOperating instructionsPractical TipsTechnical specifications

125
Heating and air conditioning
Heating and air conditioning
Heating and air conditioning General notes
The power of the heating depends on the temperature of the coolant. There-
fore, maximum power is only obtained when the engine has reached operat-
ing temperature.
The temperature and the humidity of the air is reduced when the system
cools the interior of the vehicle. This therefore increases the comfort of all
vehicle occupants when outside temperatures and humidity are high. It also
helps prevent the windows from misting over during cold periods of the
year.
The air recirculation system can be switched on temporarily to increase the
cooling effect.
Keep the air intake slots in front of the windscreen clear of ice, snow or
leaves to ensure unimpaired heating and cooling.
When the air conditioning is on, condensation can drip from the evaporator
in the air cooling system and form a pool underneath the vehicle. This is
normal and does not indicate a leak!
WARNING
● All windows must be clear of ice, snow and condensation for driving
safety. Therefore, make sure you familiarise yourself with the correct use
of heating and ventilation, window demisting and defrosting and cooling.
● Never use the air recirculation system for too long, as it prevents
fresh air from entering the vehicle and “used” air can cause tiredness, re-
duce your attention span and cause the windows to mist over. This in-
creases the risk of an accident. Switch off the air recirculation system as
soon as the windows begin to mist over.
Note
● Used air escapes through ventilation slots in the rear of the luggage
compartment.
● Smoking is not recommended while the air recirculation system is in
use, as the smoke drawn from the interior of the vehicle settles in the evap-
orator of the air conditioning system. This causes a persistent, unpleasant
smell while the system is running that is time-consuming and expensive
(evaporator replacement) to eliminate.
● Never cover the air outlets to ensure the system operates correctly. 
Economic use of the air conditioning system
When the air conditioning is switched on, the compressor consumes engine
power and has an impact on fuel consumption.
If the vehicle interior has heated up after standing in the sun for some time,
the air inside can be cooled by opening the windows or doors to allow the
hot air to escape. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

127
Heating and air conditioning
Heating Operation
Fig. 98 Heating: controls
Temperature selection
– Turn rotary control A
⇒ Fig. 98 clockwise to increase the tem-
perature.
– Turn rotary control A
anti-clockwise to reduce the temperature.
Blower selection
– Turn rotary control B
⇒ Fig. 98 to position 1 to 4 to switch the
blower on.
– Turn rotary control B
to position 0 to switch the blower off.
– Press button 1
⇒  in Air recirculation on page 129 to close
the fresh air vent. Air distribution selection
–
Turn rotary control C
⇒ Fig. 98 to select the air vents
⇒ page 126, Air vents you wish to activate.
All controls, except control B
⇒ Fig. 98, can be set to any intermediate po-
sition.
Leave the blower activated at all times to prevent the windows from misting
over.
Note
If the system is set so that all of the air is used to defrost the windows, no
air is supplied to the footwell area. This could limit heating comfort. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

129
Heating and air conditioning
WARNING
Never use the air recirculation system for too long, as it prevents fresh air
from entering the vehicle and “used” air can cause tiredness, reduce your
attention span and cause the windows to mist over. This increases the
risk of an accident. Switch off the air recirculation system as soon as the
windows begin to mist over.

Air conditioning (manual)* General notes
The air cooling system only works if the AC button
2 ⇒ Fig. 99
⇒ page 129 is pressed and under following conditions:
● The engine is running
● The outside temperature is above +2 °C (+36 °F)
● The blower control is in position 1 – 4
When the cooling system is on and under certain conditions, air can be
blown from the vents at a temperature of approx. 5 °C (41 °F). In the event
of prolonged, irregular distribution of the air flow from the outlets and sig-
nificant differences in temperature, e.g. on leaving the vehicle, sensitive
people may catch a cold.
Note
A visit to the specialised service once a year is recommended to clean the
air conditioning system. Operation
Fig. 99 Air conditioning: controls
Temperature selection
– Turn rotary control A
⇒ Fig. 99 clockwise to increase the tem-
perature.
– Turn rotary control A
anti-clockwise to reduce the temperature.
Blower selection
– Turn rotary control B
⇒ Fig. 99 to position 1 to 4 to switch the
blower on.
– Turn rotary control B
to position 0 to switch the blower off.
– Press button 

1 ⇒ page 131, Air recirculation to close the
fresh air vent.
Air distribution selection
– Turn rotary control C
⇒ Fig. 99 to select the air vents
⇒ page 126 you wish to activate. 
Safety FirstOperating instructionsPractical TipsTechnical specifications