2012 Seat Toledo warning

198Self-help
Vehicle tool kit*
Fig. 130 Vehicle tool kit
The vehicle tool kit and the jack are stored in a box on the spare wheel or in
the spare wheel well. There is also enough space for the towing bracket ball
coupling. The box is strapped to the spare wheel with tape.
The vehicle tool kit includes the following parts (depending on equipment):
Screwdriver
Adapter for anti-theft wheel bolts
Towline anchorage
Wire hook for removing hub caps
Jack
Box spanner for wheel bolts
Clip for wheel bolt cover
Spare set of bulbs
Before stowing the jack again, screw down the arm as far as it will go. 1
2345678
WARNING
● The factory-supplied jack is only designed for changing wheels on
this model of vehicle. On no account attempt to use it for lighting heavier
vehicles or other loads. Risk of injury!
● Make sure that the vehicle tools are stored properly in the luggage
compartment.
Note
Make sure the box always remains strapped to the spare wheel with tape. 
Changing a wheel Introduction
WARNING
● If you have a puncture in moving traffic, switch on the hazard warning
lights and place the warning triangle at the obligatory distance. Observe
the applicable local legal regulations. This is for your own safety and that
of other road users.
● If you have a flat tyre, stop the vehicle well away from moving traffic.
Choose a location that is as level and solid as possible.
● If you have to change the tyre on a gradient, block the wheel opposite
the wheel being changed by placing a stone or similar object under it to
prevent the vehicle from rolling away unexpectedly.
● If the vehicle has been fitted with tyres or alloys that are different to
those fitted in manufacture, the instructions ⇒ page 189, Replacing tyres
and wheels must be followed. 

199
Self-help
WARNING (Continued)
● Always raise the vehicle with the doors closed.
● Never place parts of your body, e.g. arms and legs, underneath the
vehicle when supported only by the jack.
● Secure the base of the jack with suitable supports so that it cannot
slip. The jack could slide if the ground below it is soft and slippery and
the vehicle could slip off it. Therefore, place the jack on a firm surface or
use a large, stable base. On a slippery surface, e.g. tiles, use a non-slip
base such as a rubber mat.
● Never start the engine when the vehicle is raised. Risk of injury.
● The jack should only be used in the correct jacking points.
CAUTION
● The prescribed tightening torque for wheel bolts on steel and alloy
wheels is 120 Nm.
● If the anti-theft wheel bolt is overly tightened, this could damage the
bolt and the adapter
Note
● The set of anti-theft wheel bolts or the adapter are available from au-
thorised SEAT dealers.
● Please observe the relevant local legal regulations when changing the
wheel. 
Preparation work
Some preparation is required before changing a wheel:
– If you have a flat tyre, stop the vehicle as far away as possible
from moving traffic. The surface must be horizontal.–
All vehicle occupants should leave the vehicle . Vehicle occu-
pants should waiting in a safe place, e.g. behind the roadside
crash barrier) while the wheel is being changed.
– Switch off the ignition and engage neutral or move the selector
lever on the automatic gearbox to position P.
– Apply the handbrake firmly.
– If towing a trailer, unhitch it.
– Take the vehicle tool kit ⇒ page 198 and the spare wheel
⇒ page 198 out of the luggage compartment. 
Changing a wheel
If possible, change the wheel on a level surface.
– Pull off the hub cap ⇒ page 191 or the wheel bolt covers
⇒ page 191.
– First loosen the anti-theft wheel bolts and then the other wheel
bolts ⇒ page 200.
– Raise the vehicle until the wheel to be changed is no longer
touching the ground ⇒ page 201.
– Remove the wheel bolts and place them on a clean surface
(cloth, paper, etc.).
– Take off the wheel.
– Lift the spare wheel into position and tighten the wheel bolts
lightly. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

201
Self-help
– Grip the box spanner as close to the end as possible and tight-
en the bolt firmly by turning clockwise.
WARNING
The wheel bolts should only be loosened slightly (about one turn) before
raising the vehicle with the jack. Risk of accident!
Note
If the wheel bolt is very tight, it may be possible to loosen it by pushing
down the end of the box spanner carefully with your foot. Hold on to the ve-
hicle for support and take care not to slip. 
Raising the vehicle
Fig. 132 Changing a
wheel: Jacking points
Fig. 133 Fitting the jack
To place the jack, locate the jacking point under the door sill clos-
est to the wheel to be changed ⇒ Fig. 132. The jacking point is di-
rectly underneath the stamp on the door sill.
– Turn the crank handle on the jack to wind it up under the jack-
ing point until its claw is directly below the jacking point of the
door sill.
– Adjust the jack so that its claw surrounds the jacking point on
the door sill ⇒ Fig. 133 - B underneath the stamp on the door
sill.
– Make sure that the base of the jack is entirely supported on a
flat surface and that it is vertical ⇒ Fig. 133 to the point where
the claw surrounds the jacking point on the door sill.
– Continue to wind up the jack using the crank handle until the
defective wheel is clear off the ground. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

203
Self-help
WARNING
● If you have a puncture in moving traffic, switch on the hazard warning
lights and place the warning triangle at the obligatory distance. Observe
the applicable local legal regulations. This is for your own safety and that
of other road users.
● If you have a flat tyre, stop the vehicle well away from moving traffic.
Choose a location that is as level and solid as possible.
● A tyre filled with sealant does not have the same performance proper-
ties as a conventional tyre.
● Do not drive faster than 80 km/h (50 mph).
● Avoid heavy acceleration, hard braking and fast cornering.
● Check the tyre pressure after 10 minutes of driving!
● The sealant is harmful to health and must be immediately rinsed from
affected skin.
For the sake of the environment
Used or out-of-date sealant must be disposed of in line with environmental
protection regulations.
Note
● Observe the instructions for use provided by the tyre repair kit manufac-
turer.
● A new can of sealant can be acquired from the selection of SEAT Original
Accessories.
● Change the tyre repaired using the tyre repair kit as soon as possible or
ask an Official Service about the possibility of repair. Tyre repair kit components
Fig. 135 Tyre repair kit
components
The tyre repair kit includes the following parts:
An adapter to fit and remove the valve
Sticker indicating the speed: “max. 80 km/h” or “max. 50 mph”
Flexible filling hose with cap
Compressor
Flexible tyre inflating hose
Tyre pressure gauge
Air release screw
ON/OFF button
12 Volt cable connector ⇒ page 119
Can of sealant
Spare valve
The valve extractor 1

⇒  Fig. 135 has a slot in its lower end that fits onto
the valve insert. This is used to remove the valve insert from the tyre and to
replace it. This is also valid for the spare valve insert 11
.
1
234567891011
Safety FirstOperating instructionsPractical TipsTechnical specifications

205
Self-help
– Switch the compressor off.
– When an air pressure of 2.0 – 2.5 bar cannot be reached, un-
screw the flexible pipe 5
from the tyre valve.
– Drive the vehicle approx. 10 metres forwards or backwards, so
that the sealant can “spread evenly” in the tyre.
– Screw the flexible hose from the air compressor 5
back onto
the tyre valve and repeat the inflation process.
– If the pressure is still lower than specified, the tyre is too badly
damaged. The tyre cannot be repaired using the tyre sealant kit
⇒ 
.
– Switch the compressor off.
– Unscrew the flexible hose 5
from the tyre valve.
When a tyre pressure of 2.0 – 2.5 bar is reached then you can con-
tinue driving at a max. speed of 80 km/h (50 mph).
Check the tyre pressure after 10 minutes of driving ⇒ page 205.
WARNING
● The flexible tyre filling hose and the air compressor may heat up dur-
ing the filling process. Risk of injury!
● Do not place the hot flexible tyre filling hose or hot air compressor on
top of flammable materials. Risk of fire!
● If the tyre cannot be inflated to a minimum pressure of 2.0 bar then
the tyre is too badly damaged. The sealing product is unable to seal the
tyre  . Do not drive on and obtain professional assistance.
CAUTION
Do not use the air compressor for longer than 8 minutes at a time. Risk of
overheating! Before using the air compressor again, leave it to cool down
for several minutes. 
Check after 10 minutes of driving
Check the tyre pressure after 10 minutes of driving!
If the tyre pressure is less than 1.3 bar:
–  Do not drive on! The tyre cannot be sufficiently filled using
the tyre repair kit.
– See professional assistance.
If the tyre pressure is over 1.3 bar:
– Correct the tyre pressure again to the correct value (see inside
of the fuel tank flap).
– Carefully resume your journey to the nearest specialised work-
shop at a maximum speed of 80 km/h (50 mph). 
Jump-starting
Introduction
If the engine fails to start because of a discharged battery, the battery can
be connected to the battery of another vehicle to start the engine. Suitable
jump leads are required. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

206Self-help
Both batteries must be rated at 12 Volts. The capacity (Ah) of the booster
battery should not be significantly lower than that of the discharged battery.
Jump leads
The jump leads must be heavy enough to carry the starter current and must
be fitted with insulated battery clamps. Refer to the instructions given by
the manufacturer.
Positive cable – usually red
Negative cable – usually black
WARNING
● When it is discharged, a battery can freeze at temperatures around
0 °C (32 °F). A frozen battery must first be thawed out before connecting
the jump leads. Risk of explosion!
● Please note the safety warnings referring to working in the engine
compartment ⇒ page 173.
● The non-insulated parts of the battery clamps must not be allowed to
touch. Additionally, the jump lead attached to the positive battery termi-
nal must not touch metal parts of the vehicle. Risk of short circuit!
● Do not connect the negative lead to the negative terminal of the dis-
charged battery. In the event of sparks when starting the engine, the ex-
plosive gas given off by the battery could catch fire.
● Position the jump leads in such a way that they cannot come into con-
tact with any moving parts in the engine compartment.
● Do not bend over the battery. Risk of acid burns!
● The screw plugs on the battery cells must be screwed in firmly.
● Keep sources of fire (flames, lit cigarettes, etc.) away from the bat-
tery. Risk of explosion!
● Never use the jump leads on batteries in which the electrolyte level is
too low. Risk of explosion and acid burns.
Note
● The vehicles must not touch each other, as electricity could flow as soon
as the positive terminals are connected.
● The discharged battery must be properly connected to the vehicle elec-
trical system.
● The jump leads should be checked in a specialist vehicle battery shop. 
Starting the engine
Fig. 136 Jump-starting
with the battery of anoth-
er vehicle: A – Dis-
charged battery, B –
Boosting battery
The two jump leads must be connected in the correct sequence:
Connecting the positive terminals with the positive lead
– Connect one end 1
⇒ Fig. 136 to the positive terminal of the
flat battery A.
– Connect the other end 2
to the positive terminal of the boost-
ing battery B. 

210Fuses and bulbs
Fuses and bulbs
Fuses
Introduction
All the electrical circuits are protected by fuses.
● Switch off the ignition and the electrical component concerned before
changing a fuse.
● Identify the fuse corresponding to the failed electrical component
⇒ page 211, Fuses in the dash panel, or ⇒ page 214, Changing fuses in
the engine compartment.
● Take the plastic clip from inside the fuse cover, fit it onto the blown fuse
and pull the fuse out.
● Replace the blown fuse (which will have a melted metal strip) with a new
fuse of the same amp rating.
Fuse colour code
ColourMaximum amp rating
light brown5dark brown7,5red10blue15yellow20white25green30
WARNING
Read and follow the warnings ⇒ page 173, Engine compartment before
starting work in the engine compartment.
CAUTION
● Never “repair” a fuse or replace it by fitting a fuse with a higher amp rat-
ing. Risk of fire! This could also cause damage to other parts of the electri-
cal system.
● If a newly replaced fuse blow again when the electrical component con-
cerned is switched on, the electrical system must be checked by an Official
Service as soon as possible.
Note
● It is advisable to always keep spare fuses in the vehicle. The spare fuse
box is available in the range of original SEAT parts.
● One single electrical component could have more than one fuse.
● Several electrical components may be protected by the same fuse. 

215
Fuses and bulbs
WARNING
● Take particular care when working on components in the engine com-
partment if the engine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
● The high voltage element of gas discharge bulbs* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.
CAUTION
● Remove the ignition key before working on the electric system. Other-
wise, a short circuit could occur.
● Switch off the lights and the parking light before changing a bulb.
For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the prop-
er manner.
Note
● Depending on weather conditions (cold or wet), the front lights, the fog
lights, the rear lights and the turn signals may be temporarily misted. This
has no influence on the useful life of the lighting system. By switching on
the lights, the area through which the beam of light is projected will quickly
be demisted. However, the edges may remain misted.
● Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the inter-
est of your own safety, but also in that of all other road users. ●
Before changing a bulb, make sure you have the correct new bulb.
● Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will va-
porise as a result of the heat generated by the bulb, they will be deposited
on the reflector and will impair its surface. 
Double headlight bulbs
Fig. 146 Main headlight
bulbs
Installation position of double headlight bulbs side light
main beam headlight
dipped beam headlight
turn signal light
daytime driving light 
A
BCDE
Safety FirstOperating instructionsPractical TipsTechnical specifications