2012 RENAULT SCENIC fuel

13B-481
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP6 Fuel system leaks
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
IMPORTANT:
Please observe the cleanliness guidelines and safety advice.
Procedure for checking for an external leak on the fuel circuit:
Clean away traces of grease with clean thinner and wipe the part or parts concerned with cleaning cloths.
Start the engine and increase the engine temperature until the diesel fuel reaches 40/50°C.
Stop the engine and check for traces of grease on the part or parts concerned.
If this is the case, replace the part or parts concerned.
Does the priming bulb show traces of grease?
(Visual and tactile inspections)
Check the assembly of the components and
the condition of the seal at the union of the two
components, if the leak is at the seal.
Replace the part or the parts concerned.
Bleed the fuel circuit and continue the checks.
Check the counter pressure valve located on
the fuel return line, after the injectors. Does the diesel filter show traces of grease?
(Visual and tactile inspections)
Do the fuel return pipes show traces of grease?
(Visual and tactile inspections)
YES
NO
YES
NO
YES
NO
A
EDC16CP33_V18_ALP06 / EDC16CP33_V1C_ALP06 / EDC16CP33_V54_ALP06 / EDC16CP33_V20_ALP06 / EDC16CP33_V58_ALP06 /
EDC16CP33_V5C_ALP06 / EDC16CP33_V24_ALP06 / EDC16CP33_V04_ALP06 / EDC16CP33_V08_ALP06 / EDC16CP33_V44_ALP06 /
EDC16CP33_V4C_ALP06 / EDC16CP33_V34_ALP06 / EDC16CP33_V38_ALP06 / EDC16CP33_V74_ALP06 / EDC16CP33_V28_ALP06 /
EDC16CP33_V62_ALP06 / EDC16CP33_V26_ALP06 / EDC16CP33_V60_ALP06
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-483
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP6
CONTINUED 2
– Run command SC035 High pressure fuel circuit fault
finding.
– While running the test, check that there are no leaks from the
high pressure circuit.
Is there a leak from the high pressure circuit?
End of fault finding.
Reminder:
Only replace the rail, pump or injector if there is damage to the union and this damage is visible during checks.
Bleed the fuel circuit and continue the checks.
NO
B
C
YES
NO
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-484
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP7 Rough idle
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
Check the sealing and the condition of the
inlet circuit: run Test 4 Turbocharged air
inlet circuit check. Check the low
pressure circuit: run Test 3 Low pressure
circuit check. Check the engine parameters:
– Check the update of the engine management
computer calibration (last calibration).
– Check the conformity of the IMA* codes (see
Interpretation of commands, SC002 Enter injector
codes).
Check the charging circuit using Technical Note 6014A,
Charging circuit check, Alternator fault finding, 16A,
Alternator (formerly Technical Note 3455A).
– Check that the engine speed signal is correct using an
oscilloscope: no interference, broken tooth, etc.
– If not correct, check:
– The wiring.
– The flywheel position and the condition of the flywheel
teeth.
– Check the position and tightness of the engine speed
sensor. – Check the connections and wiring of the
injectors.
– Check the connections and wiring of the
engine management computer to the
injectors.
Check the high pressure circuit (external
leaks).
(see the end of the Fuel circuit external
leaks fault finding chart)
A
EDC16CP33_V18_ALP07 / EDC16CP33_V1C_ALP07 / EDC16CP33_V54_ALP07 / EDC16CP33_V20_ALP07 / EDC16CP33_V58_ALP07 /
EDC16CP33_V5C_ALP07 / EDC16CP33_V24_ALP07 / EDC16CP33_V04_ALP07 / EDC16CP33_V08_ALP07 / EDC16CP33_V44_ALP07 /
EDC16CP33_V4C_ALP07 / EDC16CP33_V34_ALP07 / EDC16CP33_V38_ALP07 / EDC16CP33_V74_ALP07 / EDC16CP33_V28_ALP07 /
EDC16CP33_V62_ALP07 / EDC16CP33_V26_ALP07 / EDC16CP33_V60_ALP07
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-492V12 MR-372-J84-13B300$180.mif
13B
*Technical Note 3419: Fault finding on the turbocharger for petrol and diesel engines. EXHAUST SYSTEM CHECK TEST1
RESOLVING MISFIRESTEST2
LOW PRESSURE CIRCUIT CHECK TEST3
TURBOCHARGED AIR INLET CIRCUIT CHECK TEST4
AIR FLOW SENSORTEST5
FUEL RETURN RAIL VALVE CHECK TEST6
VARIABLE GEOMETRY TURBOCHARGER CONTROLTEST 7: Apply
TEST 4 of
Technical Note
3419*
ROTATING PART OF TURBOCHARGERTEST 8: Apply
TEST 7 of
Technical Note
3419*
POOR INJECTOR OPERATION TEST10
TEMPERATURE UPSTREAM OF TURBINE TOO LOW TEST11
DIESEL FUEL CONFORMITY CHECK TEST12
DIESEL INJECTION
Fault finding – Test
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-495V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST2 Resolving misfires
Check for faults DF059 Misfire on cylinder 1, DF060
Misfire on cylinder 2, DF061 Misfire on cylinder 3,
DF062 Misfire on cylinder 4, DF065 Misfire using the
diagnostic tool.
Run a compression test using the M9R flexible end piece,
part number Mot. 1772 and apply command VP036 Fuel
supply inhibition (see Interpretation of commands).
Are the values obtained correct?Check the mechanical conformity of the
valves, heater plugs and segments.
Clear the faults, start the engine and leave the engine
running at idle speed for 1 minute.
Check for faults DF059, DF060, DF061, DF062, DF065
using the diagnostic tool.
Are there any faults remaining?End of test.
Change the faulty injector to another position.
Did the fault follow the injector to its new location?Put the injectors back in their initial
positions.
NO
YES
NO
YES
NO
YES
A
EDC16CP33_V18_TEST2 / EDC16CP33_V1C_TEST2 / EDC16CP33_V54_TEST2 / EDC16CP33_V20_TEST2 / EDC16CP33_V58_TEST2 /
EDC16CP33_V5C_TEST2 / EDC16CP33_V24_TEST2 / EDC16CP33_V04_TEST2 / EDC16CP33_V08_TEST2 / EDC16CP33_V44_TEST2 /
EDC16CP33_V4C_TEST2 / EDC16CP33_V34_TEST2 / EDC16CP33_V38_TEST2 / EDC16CP33_V74_TEST2 / EDC16CP33_V28_TEST2 /
EDC16CP33_V62_TEST2 / EDC16CP33_V26_TEST2 / EDC16CP33_V60_TEST2
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-497V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST3 Low pressure circuit check
Check the fuel filter:
– Conformity of the fuel filter (correct part number and RENAULT filter).
– Positioning and degree of clogging of the filter cartridge.
– Positioning and condition of the seals.
– If there is metal swarf in the filter:
Replace the fuel filter, bleed the circuit and continue the fault finding procedure.
Supplying the injection system with fuel from an additional tank.
This operation aims to detect possible faults in the low pressure supply system of a vehicle by replacing it entirely
with an additional tank.
Mode:
– Disconnect the diesel fuel supply pipe at the fuel filter inlet and block it with a plug.
– Connect a pipe to the fuel filter inlet and insert the other end in a clean container with a capacity of approximately
5 litres.
– Disconnect the diesel fuel return pipe at the diesel temperature sensor (pump return and injector return join), and
block it using a plug.
– Connect a transparent pipe to the union of the diesel fuel temperature sensor, and insert the other end in the
container.
– Fill the container with clean diesel fuel.
– Start the engine and let the system drain itself of its air (there must not be any air bubbles in the return pipe).
Is the customer complaint still present?If the low pressure circuit is in order, reconnect the
various low pressure circuit pipes, and repeat the
fault finding chart procedure or the procedure for
the fault that referred you to this test.
Are the low pressure circuit connections in order
and in good condition?Carry out the necessary repairs.
YES
NO
NO
A
YES
EDC16CP33_V18_TEST3 / EDC16CP33_V1C_TEST3 / EDC16CP33_V54_TEST3 / EDC16CP33_V20_TEST3 / EDC16CP33_V58_TEST3 /
EDC16CP33_V5C_TEST3 / EDC16CP33_V24_TEST3 / EDC16CP33_V04_TEST3 / EDC16CP33_V08_TEST3 / EDC16CP33_V44_TEST3 /
EDC16CP33_V4C_TEST3 / EDC16CP33_V34_TEST3 / EDC16CP33_V38_TEST3 / EDC16CP33_V74_TEST3 / EDC16CP33_V28_TEST3 /
EDC16CP33_V62_TEST3 / EDC16CP33_V26_TEST3 / EDC16CP33_V60_TEST3
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-498V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST3
CONTINUED
Check the condition and operation of the priming bulb. Perform repairs if necessary and continue the test.
Check the condition of all the low pressure diesel pipes from the tank to the injection pump (in particular no pinching
of pipes).
If the fault is still present with a low fuel level, check the consistency of the actual fuel level and that indicated on
the instrument panel.
The transfer pump is supplied via a Venturi pipe located underneath it.
Check that the opening of the venturi (6 mm to 8 mm in diameter) is not blocked by dirt contained in the fuel tank.
Check the priming of the low pressure diesel circuit.
Check that the fuel tank is correctly filled and that the fuel is correct (see Test 12 Diesel fuel conformity check).
If the diesel fuel is not correct:
– Replace the fuel (diesel fuel).
– Replace the fuel filter (diesel fuel).
– Bleed the low and high pressure fuel circuit (diesel fuel).
Low pressure circuit correct.
A
YES
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-502V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST6 Fuel return rail valve check
This test consists of creating a vacuum downstream of the anti-return valve of the injector return rail and checking
whether fuel is drawn in by the valve.
Fitting:
Remove the rail protector.
Disconnect the union of the return rail on injector 4 (on the gearbox side).
Disconnect the union downstream of the anti-return valve.
Connect the 8 mm quick-release coupling.
Connect a transparent hose (resistant to diesel, length 60 cm and internal diameter 8 mm).
Connect a manual vacuum pump.
Gradually apply a vacuum up to 0.5 bar.
If more than a cm of diesel is quickly drawn into the hose, the valve is leaking. Stop the vacuum immediately.
Replace the diesel injector fuel return rail and its overpressure valve (see MR364 (Mégane II ph2), MR370 (Scénic
II ph2), MR 395 (Laguna II ph2), MR 402 (Vel-Satis ph2), MR405 (Espace IV ph2) Mechanical, 13B, Diesel
injection, Diesel injector fuel return rail: Removal - Refitting).
Otherwise, maintain the vacuum for 1 minute.
If less than a cm of diesel is drawn into the hose, the valve of the rail is not leaking.
End of test.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
EDC16CP33_V18_TEST6 / EDC16CP33_V1C_TEST6 / EDC16CP33_V54_TEST6 / EDC16CP33_V20_TEST6 / EDC16CP33_V58_TEST6 /
EDC16CP33_V5C_TEST6 / EDC16CP33_V24_TEST6 / EDC16CP33_V04_TEST6 / EDC16CP33_V08_TEST6 / EDC16CP33_V44_TEST6 /
EDC16CP33_V4C_TEST6 / EDC16CP33_V34_TEST6 / EDC16CP33_V38_TEST6 / EDC16CP33_V74_TEST6 / EDC16CP33_V28_TEST6 /
EDC16CP33_V62_TEST6 / EDC16CP33_V26_TEST6 / EDC16CP33_V60_TEST6