2012 RENAULT SCENIC coolant temperature

13B-270V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET034CLUTCH SIGNAL DETECTED
STATUS
DEFINITIONNO: This status indicates that the clutch pedal has not been depressed since
the ignition was switched on.
YES: This status indicates that the clutch pedal has been depressed since the
ignition was switched on.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOWhen the vehicle ignition is switched on without depressing the clutch pedal,
statusET034 is NO.
EDC16CP33_V18_ET034 / EDC16CP33_V1C_ET034 / EDC16CP33_V54_ET034 / EDC16CP33_V20_ET034 / EDC16CP33_V58_ET034 /
EDC16CP33_V5C_ET034 / EDC16CP33_V24_ET034 / EDC16CP33_V04_ET034 / EDC16CP33_V08_ET034 / EDC16CP33_V44_ET034 /
EDC16CP33_V4C_ET034 / EDC16CP33_V34_ET034 / EDC16CP33_V38_ET034 / EDC16CP33_V74_ET034 / EDC16CP33_V28_ET034 /
EDC16CP33_V62_ET034 / EDC16CP33_V26_ET001 / EDC16CP33_V60_ET001
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-272V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET038ENGINE
STATUS
DEFINITION+ AFTER IGNITION: This status indicates that the engine is in + after ignition feed.
RUNNING: This status indicates that the engine is running.
STOPPED: This status indicates that the engine is stopped.
Conformity check with engine stopped and ignition on.
+ APCThis status indicates that the engine is in + after ignition feed.
In the event of a fault, switch off the ignition, wait for the message to appear on the
diagnostic tool (maximum time 8 minutes): Loss of dialogue with the computer:
EDC16 CP33, check the connection of the tool and the computer supply.
If the fault is still present, contact the Techline.
Conformity check with the engine running and engine coolant temperature > 80°C
"RUNNING"This status indicates that the engine is running.
In the event of a fault, switch off the ignition, wait for the message to appear on the
diagnostic tool (maximum time 8 minutes): Loss of dialogue with the computer:
EDC16 CP33, check the connection of the tool and the computer supply,
If the fault is still present, contact the Techline.
"STOPPED"This status indicates that the engine has just cut out, without the ignition being
switched off.
EDC16CP33_V18_ET038 / EDC16CP33_V1C_ET038 / EDC16CP33_V54_ET038 / EDC16CP33_V20_ET038 / EDC16CP33_V58_ET038 /
EDC16CP33_V5C_ET038 / EDC16CP33_V24_ET038 / EDC16CP33_V04_ET038 / EDC16CP33_V08_ET038 / EDC16CP33_V44_ET038 /
EDC16CP33_V4C_ET038 / EDC16CP33_V34_ET038 / EDC16CP33_V38_ET038 / EDC16CP33_V74_ET038 / EDC16CP33_V28_ET038 /
EDC16CP33_V62_ET038 / EDC16CP33_V26_ET038 / EDC16CP33_V60_ET038
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-273V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the main on/off switch of the cruise control/speed
limiter is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
INACTIVENo button has been pressed.
LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROLThe cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
EDC16CP33_V18_ET042 / EDC16CP33_V1C_ET042 / EDC16CP33_V54_ET042 / EDC16CP33_V20_ET042 / EDC16CP33_V58_ET042 /
EDC16CP33_V5C_ET042 / EDC16CP33_V24_ET042 / EDC16CP33_V04_ET042 / EDC16CP33_V08_ET042 / EDC16CP33_V44_ET042 /
EDC16CP33_V4C_ET042 / EDC16CP33_V34_ET042 / EDC16CP33_V38_ET042 / EDC16CP33_V74_ET042 / EDC16CP33_V28_ET042 /
EDC16CP33_V62_ET042 / EDC16CP33_V26_ET042 / EDC16CP33_V60_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-274V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 1
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOT DETECTEDIf the vehicle is not fitted with cruise control/speed limiter function buttons, status
ET042 Cruise control/speed limiter is permanently NOT DETECTED. Confirmation
of the absence of the cruise control or speed limiter function on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons and the main
switch is in the rest (or neutral) position and after the injection computer has been
programmed or reprogrammed, then status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the
cruise control position and then in the speed limiter position.
Return to rest position
The tool displays status ET042: INACTIVE.
If not, several steps must be checked:
1. Return to the multiplex network test page on the Clip application. Repeat the
multiplex network test. Re-establish dialogue with the injection computer.
CheckET042. If ET042 is INACTIVE, the injection computer has detected the
various positions of the main switch. The cruise control/speed limiter is active.
2. If ET042 is still NOT DETECTED, check that the owner of the vehicle has not
had the cruise control/speed limiter function deactivated in the past. Contact
the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-281V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET076STARTING
STATUS
DEFINITIONPROHIBITED: This status indicates that starting is not possible.
AUTHORISED: This status indicates that starting is possible.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"PROHIBITED"Refer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
"AUTHORISED"Refer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
EDC16CP33_V18_ET076 / EDC16CP33_V1C_ET076 / EDC16CP33_V54_ET076 / EDC16CP33_V20_ET076 / EDC16CP33_V58_ET076 /
EDC16CP33_V5C_ET076 / EDC16CP33_V24_ET076 / EDC16CP33_V04_ET076 / EDC16CP33_V08_ET076 / EDC16CP33_V44_ET076 /
EDC16CP33_V4C_ET076 / EDC16CP33_V34_ET076 / EDC16CP33_V38_ET076 / EDC16CP33_V74_ET076 / EDC16CP33_V28_ET076 /
EDC16CP33_V62_ET076 / EDC16CP33_V26_ET076 / EDC16CP33_V60_ET076
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-282V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET077IMPACT DETECTED
STATUS
DEFINITIONNO: This status indicates that the airbag computer has not detected an impact.
YES: This status indicates that the airbag computer has detected an impact.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
This signal is transmitted by the airbag computer via the multiplex network.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"NO"The status is usually NO as no impact has been detected.
Otherwise, check the airbag computer (see88C, Airbags and pretensioners).
"YES"If YES an impact must be present.
Otherwise, check the airbag computer (see88C, Airbags and pretensioners).
After the repair, clear the faults (even if no fault is displayed).
EDC16CP33_V18_ET077 / EDC16CP33_V1C_ET077 / EDC16CP33_V54_ET077 / EDC16CP33_V20_ET077 / EDC16CP33_V58_ET077 /
EDC16CP33_V5C_ET077 / EDC16CP33_V24_ET077 / EDC16CP33_V04_ET077 / EDC16CP33_V08_ET077 / EDC16CP33_V44_ET077 /
EDC16CP33_V4C_ET077 / EDC16CP33_V34_ET077 / EDC16CP33_V38_ET077 / EDC16CP33_V74_ET077 / EDC16CP33_V28_ET077 /
EDC16CP33_V62_ET077 / EDC16CP33_V26_ET077 / EDC16CP33_V60_ET077
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-283V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET079AIR CONDITIONING PRESENT
STATUS
DEFINITIONYES: This status indicates that air conditioning is present on the vehicle.
NO: This status indicates that air conditioning is not present on the vehicle.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
The heating and air conditioning system is present depending on the vehicle's
equipment level.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
YES or NOYES or NO, depending on the vehicle equipment.
EDC16CP33_V18_ET079 / EDC16CP33_V1C_ET079 / EDC16CP33_V54_ET079 / EDC16CP33_V20_ET079 / EDC16CP33_V58_ET079 /
EDC16CP33_V5C_ET079 / EDC16CP33_V24_ET079 / EDC16CP33_V04_ET079 / EDC16CP33_V08_ET079 / EDC16CP33_V44_ET079 /
EDC16CP33_V4C_ET079 / EDC16CP33_V34_ET079 / EDC16CP33_V38_ET079 / EDC16CP33_V74_ET079 / EDC16CP33_V28_ET079 /
EDC16CP33_V62_ET079 / EDC16CP33_V26_ET079 / EDC16CP33_V60_ET079
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-284V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
IMA*: Individual injector correction
ET104INJECTOR CODE USE
STATUS
DEFINITIONNO: This status indicates that the injector codes have not been entered.
YES: This status indicates that the injector codes have been entered.
FAULTY: This status indicates that there has been an injector code entry fault.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"NO"If status ET104 is NO, program the injector codes using:
either command SC002 Enter injector codes (the IMA* codes must be read from
left to right),
or command SC001 Write saved data when replacing with a blank computer
orafter reprogramming (see Interpretation of commands).
"YES"When injector code programming is complete, status ET104 becomes YES.
"FAULTY"If status ET104 is FAULTY, program the injector codes using:
– either command SC002 (the IMA* codes must be read from left to right),
– or command SC001 when replacing with a blank computer or after
reprogramming (see Interpretation of commands).
EDC16CP33_V18_ET104 / EDC16CP33_V1C_ET104 / EDC16CP33_V54_ET104 / EDC16CP33_V20_ET104 / EDC16CP33_V58_ET104 /
EDC16CP33_V5C_ET104 / EDC16CP33_V24_ET104 / EDC16CP33_V04_ET104 / EDC16CP33_V08_ET104 / EDC16CP33_V44_ET104 /
EDC16CP33_V4C_ET104 / EDC16CP33_V34_ET104 / EDC16CP33_V38_ET104 / EDC16CP33_V74_ET104 / EDC16CP33_V28_ET104 /
EDC16CP33_V62_ET104 / EDC16CP33_V26_ET104 / EDC16CP33_V60_ET104
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74