2012 RENAULT SCENIC test 3 low

13B-309V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
CONTINUED
STATUS 4, 17
Check for present and stored faults, and repair.
STATUS 8Reset the EGR offsets by consulting the interpretation of command SC036
Reinitialise programming and select EGR valve.
STATUS 11, 22Allow the engine to heat up until this cut-off disappears.
STATUS 18Check that the regeneration of the particle filter in progress has completely finished.
STATUS 20Allow the engine to cool until this cut-off disappears.
STATUS 21Too low atmospheric pressure, the EGR valve is disabled.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-311V12 MR-372-J84-13B300$102.mif
13B
ET703
CONTINUED 1
Sensor electrical conformity
"INACTIVE"Status ET703 becomes INACTIVE when none of the cruise control / speed limiter
buttons is pressed. These buttons are located on the steering wheel.
If status ET703 does not display INACTIVE,
– check the condition of the cruise control / speed limiter +/- button and the condition
of its connector,
– check the condition of the cruise control / speed limiter R/0 button and the condition
of its connector.
"PLUS"Status ET703 becomes PLUS when the cruise control / speed limiter + button is
pressed. This button is on the steering wheel, on the left-hand side.
If status ET703 does not display INCREASE, check the condition of the cruise
control/speed limiter +/- button and the condition of its connector. Repair if necessary.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the + button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 300 Ω, check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the +/- control button.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
DIESEL INJECTION
Fault finding – Interpretation of statuses
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-312V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 2
"MINUS"
Status ET703 becomes DECREASE when the - button of the cruise control/speed
limiter is pressed. This button is on the steering wheel, on the left-hand side.
If status ET703 does not change to MINUS, check the condition of the cruise control/
speed limiter +/- button, and the condition of its connector. Repair if necessary.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the - button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 100 Ω check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the +/- control button.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-313V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 3
"SUSPEND"
Status ET703 becomes SUSPEND when the cruise control / speed limiter 0 button is
pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to SUSPEND, check the condition of the cruise
control / speed limiter R/0 button, and the condition of its connector.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the 0 button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 0 Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-314V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 4
"REACTIVATE"
Status ET703 becomes RESUME when the R button of the cruise control/speed
limiter is pressed. This button is located on the steering wheel, to the right.
If status ET703 does not change to RESUME, check the status of the cruise control/
speed limiter R/0 button, and the status of its connector. Repair if necessary.
To perform these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR Mechanical, 88C,
Airbag and pretensioners, Driver's front airbag: Removal - Refitting).
Measure the resistance of the following connections while pressing the R button
(on the button connections):
•86G of component 331,
•86M of component 331.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the resistance is not approximately 900 Ω, check the continuity of the connection
when the button is not pressed.
If there is continuity, replace the R/0 control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-316V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
CONTINUED 1
Sensor electrical conformity
"ACTIVE"
or
"INACTIVE"If the brake lights are working:
– check the continuity and the absence of interference resistance on the
following connection:
•5A between components 160 and 120 / 645 / 119.
If there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
For MEGANE II ph2 and SCENIC II ph2 with ESP:
Continuity between
connections:Insulation between
connections:
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
For MEGANE II ph2 and SCENIC II ph2 without ESP:
Continuity between
connections:Insulation between
connections:
Switch engaged
(Brake pedal released)5A BPT 65A SP17
Switch released
(Brake pedal depressed)65A SP17 5A BPT
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-323V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET781HEATER PLUGS
STATUS
DEFINITIONThis status indicates what type of heater plugs are fitted to the engine.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS1Slow plugs
STATUS2Fast plugs
STATUS3NOT DEFINED
Electrical conformity
STATUS1Slow plugs
Status ET781 is STATUS 1 if the heater plugs fitted to the engine have black rings,
otherwise run command SC036 Reinitialise programming and select HEATER
PLUGS (see Interpretation of commands).
EDC16CP33_V20_ET781 / EDC16CP33_V24_ET781 / EDC16CP33_V04_ET781 / EDC16CP33_V08_ET781 / EDC16CP33_V44_ET781 /
EDC16CP33_V4C_ET781 / EDC16CP33_V34_ET781 / EDC16CP33_V38_ET781 / EDC16CP33_V74_ET781 / EDC16CP33_V28_ET781 /
EDC16CP33_V62_ET781/ EDC16CP33_V26_ET781 / EDC16CP33_V60_ET781
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 20, 24,
26, 28, 34, 38, 44, 4C, 60,
62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-337
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR017FUEL FLOW
PARAMETER
DEFINITIONThis parameter indicates the fuel flow in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on
The fuel flow value must be:
PR017 = 0 mg/st (ignition on).
In the event of a fault, consult the interpretation of DF897 Pump pressure regulator circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
Engine running: PR017 = PR157: Fuel flow setpoint.
In the event of a fault, refer to the interpretation of fault DF897.
EDC16CP33_V18_PR017 / EDC16CP33_V1C_PR017 / EDC16CP33_V54_PR017 / EDC16CP33_V20_PR017 / EDC16CP33_V58_PR017 /
EDC16CP33_V5C_PR017 / EDC16CP33_V24_PR017 / EDC16CP33_V04_PR017 / EDC16CP33_V08_PR017 / EDC16CP33_V44_PR017 /
EDC16CP33_V4C_PR017 / EDC16CP33_V34_PR017 / EDC16CP33_V38_PR017 / EDC16CP33_V74_PR017 / EDC16CP33_V28_PR017 /
EDC16CP33_V62_PR017 / EDC16CP33_V26_PR017 / EDC16CP33_V60_PR017
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74