2012 RENAULT SCENIC check engine

13B-304V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 6
STATUS 9
Vehicle speed monitoring.
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
Interpretation of faults).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If STATUS 9 is still present, contact the Techline.
STATUS 10Monitoring by injection computer.
Status ET415 becomes STATUS 10 when driving with cruise control active
(ET042 Cruise control / speed limiter: CRUISE CONTROL) and if the injection
computer detects a fault anywhere in the engine management system, or an
engine overspeed or underspeed.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with any present or stored faults (see Interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ001.
If STATUS 10 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-305V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET587RECIRCULATED EXHAUST GAS COOLING
STATUS
DEFINITIONACTIVE: This status indicates that exhaust gas cooling is recirculated.
INACTIVE: This status indicates that exhaust gas cooling is not recirculated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE:
According to computer programming.
In the event of a fault, consult the interpretation of faults
DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation
.
EDC16CP33_V18_ET587 / EDC16CP33_V1C_ET587 / EDC16CP33_V54_ET587 / EDC16CP33_V20_ET587 / EDC16CP33_V58_ET587 /
EDC16CP33_V5C_ET587 / EDC16CP33_V24_ET587 / EDC16CP33_V04_ET587 / EDC16CP33_V08_ET587 / EDC16CP33_V44_ET587 /
EDC16CP33_V4C_ET587 / EDC16CP33_V34_ET587 / EDC16CP33_V38_ET587 / EDC16CP33_V74_ET587 / EDC16CP33_V28_ET587 /
EDC16CP33_V62_ET587 / EDC16CP33_V26_ET587 / EDC16CP33_V60_ET587
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-306V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET615AUTOMATIC GEARBOX LEVER POSITION
STATUS
DEFINITIONNeutral, 1, 2, 3, 4, 5, 6, reverse.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Note:
This status is specific to engine types M9R 721 and M9R 761.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NEUTRALThis status indicates that the gear lever is in neutral.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
1This status indicates that the gearbox is in 1st gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
2This status indicates that the gearbox is in 2nd gear.
If this status is incorrect,
perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
EDC16CP33_V18_ET615 / EDC16CP33_V1C_ET615 / EDC16CP33_V54_ET615 / EDC16CP33_V20_ET615 / EDC16CP33_V58_ET615 /
EDC16CP33_V5C_ET615 / EDC16CP33_V24_ET615 / EDC16CP33_V28_ET615 / EDC16CP33_V62_ET615 / EDC16CP33_V26_ET615 /
EDC16CP33_V60_ET615
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-308V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651EGR PROGRAMMING CUT-OFF
STATUS
DEFINITIONThis status indicates the operating mode of the EGR valve and has 25 different
definitions: STATUS 1 to 24 or NONE.
NOTESNone.
NONENo EGR cut-off, the EGR valve is operating correctly in accordance with
the computer programs.
STATUSES
1, 5, 6, 7, 9, 10, 12,
13, 15, 19, 23, 24Switch off the engine and wait for the diagnostic tool message (maximum time
8 minutes) Communication lost with the computer: EDC16CP33, check the
tool connection and computer supply.
Switch the ignition on and check for faults.
Check the battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much or attain an engine speed that is too high.
STATUSES
3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal status (ET405 Clutch pedal switch) is not ACTIVE,
and that the vehicle has stopped completely.
EDC16CP33_V18_ET651 / EDC16CP33_V1C_ET651 / EDC16CP33_V54_ET651 / EDC16CP33_V20_ET651 / EDC16CP33_V58_ET651 /
EDC16CP33_V5C_ET651 / EDC16CP33_V24_ET651 / EDC16CP33_V04_ET651 / EDC16CP33_V08_ET651 / EDC16CP33_V44_ET651 /
EDC16CP33_V4C_ET651 / EDC16CP33_V34_ET651 / EDC16CP33_V38_ET651 / EDC16CP33_V74_ET651 / EDC16CP33_V28_ET651 /
EDC16CP33_V62_ET651 / EDC16CP33_V26_ET651 / EDC16CP33_V60_ET651
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-309V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651
CONTINUED
STATUS 4, 17
Check for present and stored faults, and repair.
STATUS 8Reset the EGR offsets by consulting the interpretation of command SC036
Reinitialise programming and select EGR valve.
STATUS 11, 22Allow the engine to heat up until this cut-off disappears.
STATUS 18Check that the regeneration of the particle filter in progress has completely finished.
STATUS 20Allow the engine to cool until this cut-off disappears.
STATUS 21Too low atmospheric pressure, the EGR valve is disabled.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-310V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS
DEFINITIONRESUME: R button pressed.
SUSPEND: 0 button pressed.
PLUS: Increase button pressed.
MINUS: Decrease button pressed
.
INACTIVE: This status indicates that no button has been pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"INACTIVE"When no button has been pressed.
In the event of a fault, refer to the interpretation of status ET703.
"SUSPEND"'0' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"REACTIVATE"'R' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"MINUS"Decrease button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"PLUS"Increase button pressed.
In the event of a fault, refer to the interpretation of status ET703.
EDC16CP33_V18_ET703 / EDC16CP33_V1C_ET703 / EDC16CP33_V54_ET703 / EDC16CP33_V20_ET703 / EDC16CP33_V58_ET703 /
EDC16CP33_V5C_ET703 / EDC16CP33_V24_ET703 / EDC16CP33_V04_ET703 / EDC16CP33_V08_ET703 / EDC16CP33_V44_ET703 /
EDC16CP33_V4C_ET703 / EDC16CP33_V34_ET703 / EDC16CP33_V38_ET703 / EDC16CP33_V74_ET703 / EDC16CP33_V28_ET703 /
EDC16CP33_V62_ET703 / EDC16CP33_V26_ET703 / EDC16CP33_V60_ET703
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-315V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS
DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
NOTESNote:
Statuses ET704 and ET705 must change specification at the same time. If they are
inconsistent, refer to the interpretation of fault DF228 Brake signal.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"ACTIVE"Brake pedal depressed.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, consult the interpretation of ET704 and ET705.
"INACTIVE"Brake pedal released.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, consult the interpretation of ET704 and ET705.
EDC16CP33_V18_ET704 / EDC16CP33_V18_ET705 / EDC16CP33_V1C_ET704 / EDC16CP33_V1C_ET705 / EDC16CP33_V54_ET704 /
EDC16CP33_V54_ET705 / EDC16CP33_V20_ET704 / EDC16CP33_V20_ET705 / EDC16CP33_V58_ET704 / EDC16CP33_V58_ET705 /
EDC16CP33_V5C_ET704 / EDC16CP33_V5C_ET705 / EDC16CP33_V24_ET704 / EDC16CP33_V24_ET705 / EDC16CP33_V04_ET704 /
EDC16CP33_V04_ET705 / EDC16CP33_V08_ET704 / EDC16CP33_V08_ET705 / EDC16CP33_V44_ET704 / EDC16CP33_V44_ET705 /
EDC16CP33_V4C_ET704 / EDC16CP33_V4C_ET705 / EDC16CP33_V34_ET704 / EDC16CP33_V34_ET705 / EDC16CP33_V38_ET704 /
EDC16CP33_V38_ET705 / EDC16CP33_V74_ET704 / EDC16CP33_V74_ET705 / EDC16CP33_V28_ET704 / EDC16CP33_V28_ET705 /
EDC16CP33_V62_ET704 / EDC16CP33_V62_ET705 / EDC16CP33_V26_ET704 / EDC16CP33_V60_ET704 / EDC16CP33_V26_ET705 /
EDC16CP33_V60_ET705
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-318V12 MR-372-J84-13B300$102.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET706
ET707
ET708
ET709
ET710
ET711
ET712
ET713
ET714
ET715STORED ENGINE STATUS NO. 1
STORED ENGINE STATUS NO. 2
STORED ENGINE STATUS NO. 3
STORED ENGINE STATUS NO. 4
STORED ENGINE STATUS NO. 5
STORED ENGINE STATUS NO. 6
STORED ENGINE STATUS NO. 7
STORED ENGINE STATUS NO. 8
STORED ENGINE STATUS NO. 9
STORED ENGINE STATUS NO. 10
STATUS
DEFINITIONThese statuses indicate the recorded engine status in the event of a regeneration
failure when driving.
NOTESSpecial notes:
These parameters must only be interpreted for DF312 Speed request if it is present
or stored.
EDC16CP33_V18_ET706 / EDC16CP33_V18_ET707 / EDC16CP33_V18_ET708 / EDC16CP33_V18_ET709 / EDC16CP33_V18_ET710 /
EDC16CP33_V18_ET711 / EDC16CP33_V18_ET712 / EDC16CP33_V18_ET713 / EDC16CP33_V18_ET714 / EDC16CP33_V18_ET715 /
EDC16CP33_V1C_ET706 / EDC16CP33_V1C_ET707 / EDC16CP33_V1C_ET708 / EDC16CP33_V1C_ET709 / EDC16CP33_V1C_ET710 /
EDC16CP33_V1C_ET711 / EDC16CP33_V1C_ET712 / EDC16CP33_V1C_ET713 / EDC16CP33_V1C_ET714 / EDC16CP33_V1C_ET715 /
EDC16CP33_V54_ET706 / EDC16CP33_V54_ET707 / EDC16CP33_V54_ET708 / EDC16CP33_V54_ET709 / EDC16CP33_V54_ET710 /
EDC16CP33_V54_ET711 / EDC16CP33_V54_ET712 / EDC16CP33_V54_ET712 / EDC16CP33_V54_ET713 / EDC16CP33_V54_ET714 /
EDC16CP33_V54_ET715 / EDC16CP33_V20_ET706 / EDC16CP33_V20_ET707 / EDC16CP33_V20_ET708 / EDC16CP33_V20_ET709 /
EDC16CP33_V20_ET710 / EDC16CP33_V20_ET711 / EDC16CP33_V20_ET712 / EDC16CP33_V20_ET713 / EDC16CP33_V20_ET714 /
EDC16CP33_V20_ET715 / EDC16CP33_V58_ET706 / EDC16CP33_V58_ET707 / EDC16CP33_V58_ET708 / EDC16CP33_V58_ET709 /
EDC16CP33_V58_ET710 / EDC16CP33_V58_ET711 / EDC16CP33_V58_ET712 / EDC16CP33_V58_ET713 / EDC16CP33_V58_ET714 /
EDC16CP33_V58_ET715 / EDC16CP33_V5C_ET706 / EDC16CP33_V5C_ET707 / EDC16CP33_V5C_ET708 / EDC16CP33_V5C_ET709 /
EDC16CP33_V5C_ET710 / EDC16CP33_V5C_ET711 / EDC16CP33_V5C_ET712 / EDC16CP33_V5C_ET713 / EDC16CP33_V5C_ET714 /
EDC16CP33_V5C_ET715 / EDC16CP33_V24_ET706 / EDC16CP33_V24_ET707 / EDC16CP33_V24_ET708 / EDC16CP33_V24_ET709 /
EDC16CP33_V24_ET710 / EDC16CP33_V24_ET711 / EDC16CP33_V24_ET712 / EDC16CP33_V24_ET713 / EDC16CP33_V24_ET714 /
EDC16CP33_V24_ET715 / EDC16CP33_V26_ET706 / EDC16CP33_V26_ET707 / EDC16CP33_V26_ET708 / EDC16CP33_V26_ET709 /
EDC16CP33_V26_ET710 / EDC16CP33_V26_ET711 / EDC16CP33_V26_ET712 / EDC16CP33_V26_ET713 / EDC16CP33_V26_ET714 /
EDC16CP33_V26_ET715 / EDC16CP33_V60_ET706 / EDC16CP33_V60_ET707 / EDC16CP33_V60_ET708 / EDC16CP33_V60_ET709 /
EDC16CP33_V60_ET710 / EDC16CP33_V60_ET711 / EDC16CP33_V60_ET712 / EDC16CP33_V60_ET713 / EDC16CP33_V60_ET714 /
EDC16CP33_V60_ET715
EDC16CP33
Program No.: C4
VDiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.