2012 RENAULT SCENIC clutch

13B-296V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: this status indicates that the clutch pedal is depressed.
INACTIVE: this status indicates that the clutch pedal is released.
NOTESCan only be displayed for manual gearboxes.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"ACTIVE"Clutch pedal depressed.
Non-conformity of the brake signals and/or the clutch switch signals can cause
the engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
"INACTIVE"Clutch pedal released.
Non-conformity of the brake signals and/or the clutch switch signals can cause
the engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
Sensor electrical conformity
EDC16CP33_V18_ET405 / EDC16CP33_V1C_ET405 / EDC16CP33_V54_ET405 / EDC16CP33_V20_ET405 / EDC16CP33_V58_ET405 /
EDC16CP33_V5C_ET405 / EDC16CP33_V24_ET405 / EDC16CP33_V04_ET405 / EDC16CP33_V08_ET405 / EDC16CP33_V44_ET405 /
EDC16CP33_V4C_ET405 / EDC16CP33_V34_ET405 / EDC16CP33_V38_ET405 / EDC16CP33_V74_ET405 / EDC16CP33_V28_ET405 /
EDC16CP33_V62_ET405 / EDC16CP33_V26_ET405 / EDC16CP33_V60_ET405
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-297V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405
CONTINUED
"INACTIVE"
Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between connections M
and86D of component 675, with the switch in the rest position.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Repeat this operation with the switch pressed, and check the continuity between
the two connections.
If these 2 checks are faulty, replace the switch.
Then check the continuity and absence of interference resistance of the
following connection:
•86D between components120 and 675.
Check that the earth is in order on connectionM of component675.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
"ACTIVE"Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between connections M
and86D of component 675, with the switch in the rest position.
– Repeat this operation with the switch pressed, and check the continuity
between the two connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
If these 2 checks are faulty, replace the switch.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-298V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS
DEFINITIONThis status varies according to engine specifications.
NOTESNone.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control / speed limiter function, due to
a driver request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 "Fault memory" to reset this status to "NONE".
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS 1:Traction control request.
STATUS 2:Brake pedal depressed.
STATUS 3:Clutch pedal depressed.
STATUS 4:Suspend button pressed.
STATUS 5:Cruise control or speed limiter monitoring.
STATUS 6:Gear lever in neutral (manual gearbox) or neutral position (automatic gearbox).
EDC16CP33_V18_ET415 / EDC16CP33_V1C_ET415 / EDC16CP33_V54_ET415 / EDC16CP33_V20_ET415 / EDC16CP33_V58_ET415 /
EDC16CP33_V5C_ET415 / EDC16CP33_V24_ET415 / EDC16CP33_V04_ET415 / EDC16CP33_V08_ET415 / EDC16CP33_V44_ET415 /
EDC16CP33_V4C_ET415 / EDC16CP33_V34_ET415 / EDC16CP33_V38_ET415 / EDC16CP33_V74_ET415 / EDC16CP33_V28_ET415 /
EDC16CP33_V62_ET415 / EDC16CP33_V26_ET415 / EDC16CP33_V60_ET415
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-300V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when driving with the cruise control active
(ET042: CRUISE CONTROL) and brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 2 without depressing the brake pedal, consult
the interpretation of statuses ET704 Brake contact no. 1 and ET705 Brake
contact no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active
(ET042 Cruise control / speed limiter: CRUISE CONTROL) and the clutch pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-302V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 5
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 changes to STATUS 5, deal with present faults or those stored in
the injection computer.
If the fault is still present, contact the Techline.
STATUS 6Gear lever in neutral (manual gearbox) or neutral (automatic gearbox)
Status ET415 changes to STATUS 6, when driving, with cruise control active (ET042:
CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into the neutral position on an automatic
transmission, run fault finding on the ABS computer and check the configuration of the
tyre size stored in the computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-308V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651EGR PROGRAMMING CUT-OFF
STATUS
DEFINITIONThis status indicates the operating mode of the EGR valve and has 25 different
definitions: STATUS 1 to 24 or NONE.
NOTESNone.
NONENo EGR cut-off, the EGR valve is operating correctly in accordance with
the computer programs.
STATUSES
1, 5, 6, 7, 9, 10, 12,
13, 15, 19, 23, 24Switch off the engine and wait for the diagnostic tool message (maximum time
8 minutes) Communication lost with the computer: EDC16CP33, check the
tool connection and computer supply.
Switch the ignition on and check for faults.
Check the battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much or attain an engine speed that is too high.
STATUSES
3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal status (ET405 Clutch pedal switch) is not ACTIVE,
and that the vehicle has stopped completely.
EDC16CP33_V18_ET651 / EDC16CP33_V1C_ET651 / EDC16CP33_V54_ET651 / EDC16CP33_V20_ET651 / EDC16CP33_V58_ET651 /
EDC16CP33_V5C_ET651 / EDC16CP33_V24_ET651 / EDC16CP33_V04_ET651 / EDC16CP33_V08_ET651 / EDC16CP33_V44_ET651 /
EDC16CP33_V4C_ET651 / EDC16CP33_V34_ET651 / EDC16CP33_V38_ET651 / EDC16CP33_V74_ET651 / EDC16CP33_V28_ET651 /
EDC16CP33_V62_ET651 / EDC16CP33_V26_ET651 / EDC16CP33_V60_ET651
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-480
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP5 Irregular engine operation
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the engine races during gear changes, if there is a floor mat, check that this is not blocking the accelerator pedal,
the brake pedal and the clutch pedal, then check the conformity of the clutch switch and the conformity of the
accelerator pedal sensor when the pedal is released (see PR086 Pedal potentiometer voltage gang 1 and
PR088 Pedal potentiometer voltage gang 2, Sensor supply).
Measure the resistance between connections 3BG and 3BL of component 149.
If the sensor resistance is not between:
741 Ω < X < 905 Ω at +20°C, replace the sensor.
Check the continuity and absence of interference resistance on the following connections:
•3BG between the components 120 and 149,
•3BL between components 120 and 149.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting and condition (overheating) of the sensor.
Check the low pressure circuit: run Test 3 Low pressure circuit check.
Apply the air flow checking procedure, (see conformity in the interpretation of statuses and parameters).
Check the turbocharger: apply Test 7 Variable geometry turbocharger control.
If the fault is still present, test the high pressure fuel circuit:
Run scenario SC035 High pressure fuel circuit fault finding.
To interpret the result, apply the interpretation of command SC035 (see Interpretation of commands).
EDC16CP33_V18_ALP05 / EDC16CP33_V1C_ALP05 / EDC16CP33_V54_ALP05 / EDC16CP33_V20_ALP05 / EDC16CP33_V58_ALP05 /
EDC16CP33_V5C_ALP05 / EDC16CP33_V24_ALP05 / EDC16CP33_V04_ALP05 / EDC16CP33_V08_ALP05 / EDC16CP33_V44_ALP05 /
EDC16CP33_V4C_ALP05 / EDC16CP33_V34_ALP05 / EDC16CP33_V38_ALP05 / EDC16CP33_V74_ALP05 / EDC16CP33_V28_ALP05 /
EDC16CP33_V62_ALP05 / EDC16CP33_V26_ALP05 / EDC16CP33_V60_ALP05
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74