2012 RENAULT SCENIC check oil

13B-66
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF019
CONTINUED 3
1.DEFNOTESSpecial notes:This fault occurs if the computer's control
section overheats when running command AC153 High
speed fan assembly or during normal operation of the fan
assembly relay.
Check the condition of the high speed fan assembly relay mounting connector (see Wiring Diagram Technical
Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 234 or
335).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the "high-speed fan assembly" relay coil.
IMPORTANT:
Respect the measuring direction (polarity) as a protection diode is used.
Replace the relay if the resistance of the relay coil is greater than 200 Ω or less than 20 Ω.
Remove the high speed relay and check the insulation and continuity of the following connection:
3JP between components 120 and 234 or 335.
Check the + 12 V after relay feed to the high speed fan assembly relay on the following connection:
3FB of component 234 or 335.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.

13B-139
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF107
PRESENT
OR
STOREDCOMPUTER MEMORY
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– a road test followed by a power latch phase.
Special notes:
The level 1 and EOBD (European On Board Diagnostic) warning lights are lit.
If the fault is stored, clear the fault from the computer memory.
In the main screen of the CLIP diagnostic tool, note the injector codes.
Clear the computer memory using command RZ034 Computer memory.
Switch off the ignition, wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the
computer: EDC16 CP33, check the tool connection and the computer supply voltage then switch on the
ignition again.
Switch on the ignition and re-establish dialogue.
If the fault is still present, contact the Techline.
If the fault is no longer present, carry out the programming (see Programming).
Switch off the ignition, wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the
computer: EDC16 CP33, check the tool connection and the computer supply voltage then switch on the
ignition again.
For vehicles equipped with a particle filter:
– Check the exhaust pipe for leaks or blockage. Repair if necessary.
– Carry out a particle filter regeneration using command SC017 Particle filter regeneration (see Interpretation
of commands) and perform an oil change if the vehicle is not new.
EDC16CP33_V18_DF107 / EDC16CP33_V1C_DF107 / EDC16CP33_V54_DF107 / EDC16CP33_V20_DF107 / EDC16CP33_V58_DF107 /
EDC16CP33_V5C_DF107 / EDC16CP33_V24_DF107 / EDC16CP33_V04_DF107 / EDC16CP33_V08_DF107 / EDC16CP33_V44_DF107 /
EDC16CP33_V4C_DF107 / EDC16CP33_V34_DF107 / EDC16CP33_V38_DF107 / EDC16CP33_V74_DF107 / EDC16CP33_V28_DF107 /
EDC16CP33_V62_DF107 / EDC16CP33_V26_DF107 / EDC16CP33_V60_DF107

13B-257
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF1020
PRESENT
OR
STOREDENGINE OIL DILUTION
1.DEF: Above maximum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
the fault is declared present after the engine starts.
Special notes:
If the fault is present:
Particle filter regeneration inhibited,
Level 1 warning light lit,
Risk of engine damage.
Drain the engine oil.
Reset the oil wear counter.
Clear the faults.
If the fault is still present, contact the Techline.
EDC16CP33_V28_DF1020/EDC16CP33_V62_DF1020
EDC16CP33
Program No.: C4
Vdiag No.: 28, 62

13B-375V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132
CONTINUED
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold,
apply Test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, apply Test 4 of ALP 2 Starting fault or starting impossible,
– oil vapour recirculation circuit connection conformity.
–absence of leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
•3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
Check the continuity and absence of interference resistance of the following connections:
•3DV between components 120 and 799,
•3DW between components120 and 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on, and the engine stopped:
Check the voltage between connections 3DW and 3DV of component 799.
If the air flow sensor voltage is not between 0.3 V < X < 0.7 V, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-418
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$130.mif
13B
PR873OIL OXIDATION SIGNAL
STATUS
DEFINITIONThis parameter indicates the vehicle distance in miles (km) when the oil oxidation
threshold is reached.
NOTESThis parameter should only be interpreted if the OCS (Oil Control System) program is
activated on the instrument panel. On the instrument panel computer, check the
configuration reading LC106 O.C.S: WITH.
Conformity check: Engine stopped and the ignition on, or Engine running and the engine coolant
temperature > 80°C without electrical consumers
The oil condition is calculated by the oxidation program in the injection computer, according to the number of
engine revolutions.
When this count reaches a certain threshold before the end of the oil service period, the injection computer sends
a signal to the instrument panel, which will display service due. Parameter PR873 corresponds to the vehicle
mileage at the time this signal is sent.
Then the instrument panel computer deducts 900 miles (1500 km) before displaying the message Service
required.
IMPORTANT:
When the message Service due appears on the instrument panel, the customer must have the oil changed within
the remaining 900 miles (1500 km).
EDC16CP33_V5C_PR873 / EDC16CP33_V20_PR873 / EDC16CP33_V34_PR873 / EDC16CP33_V38_PR873 / EDC16CP33_V74_PR873 /
EDC16CP33_V26_PR873 / EDC16CP33_V28_PR873 / EDC16CP33_V60_PR873 / EDC16CP33_V62_PR873
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16CP33
Program No.: C4
Vdiag No.: 20, 26, 28, 34,
38, 5C, 60, 62, 74

13B-419
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$130.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR874LAST SERVICE
STATUS
DEFINITIONThis parameter indicates the vehicle's mileage at the last service in miles (km).
It is updated when the oil service parameters are reinitialised on the instrument panel.
NOTESNone.
EDC16CP33_V5C_PR874 / EDC16CP33_V20_PR874 / EDC16CP33_V34_PR874 / EDC16CP33_V38_PR874 / EDC16CP33_V74_PR874 /
EDC16CP33_V26_PR874 / EDC16CP33_V28_PR874 / EDC16CP33_V60_PR874 / EDC16CP33_V62_PR874
EDC16CP33
Program No.: C4
Vdiag No.: 20, 26, 28, 34,
38, 5C, 60, 62, 74

13B-420
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$130.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR875OIL DILUTION SIGNAL
STATUS
DEFINITIONThis parameter indicates the vehicle mileage in miles (km) when the oil dilution
threshold is reached.
NOTESThis parameter should only be interpreted if the OCS (Oil Control System) program is
activated on the instrument panel. On the instrument panel computer, check the
configuration reading LC106 O.C.S: WITH.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80°C without electrical consumers
The injection computer estimates the degree of engine oil dilution according to the customer's driving style.
When the dilution level reaches a certain threshold before the end of the oil change interval, the injection computer
sends a signal to the instrument panel which then displays Service required. Parameter PR875 corresponds to
the vehicle mileage at the time this signal is sent.
IMPORTANT:
When the message Service required appears on the instrument panel, the customer must arrange an immediate
oil change to prevent damage to the engine.
EDC16CP33_V5C_PR875 / EDC16CP33_V20_PR875 / EDC16CP33_V26_PR875 / EDC16CP33_V28_PR875 / EDC16CP33_V60_PR875 /
EDC16CP33_V62_PR875
EDC16CP33
Program No.: C4
Vdiag No.: 20, 26, 28, 5C,
60, 62

13B-421
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$130.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR1012WEIGHT OF SOOT AFTER REGENERATION
STATUS
DEFINITIONThis parameter indicates the weight in g of soot present in the particle filter following
regeneration.
NOTESThis parameter should be consulted after running SC017 Particle filter regeneration.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80°C without electrical consumers
If this parameter is less than 15 g, particle filter regeneration was successful.
If PR1012 is greater than 15 g, it is necessary to perform a second particle filter regeneration using command
SC017 Particle filter regeneration.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool down
for 2 hours with the bonnet open.
Do not carry out an engine oil change before a second After-Sales regeneration.
EDC16CP33_V1C_PR1012 / EDC16CP33_V54_PR1012 / EDC16CP33_V20_PR1012 / EDC16CP33_V58_PR1012 /
EDC16CP33_V5C_PR1012 / EDC16CP33_V24_PR1012 / EDC16CP33_V28_PR1012 / EDC16CP33_V62_PR1012/
EDC16CP33_V26_PR1012 / EDC16CP33_V60_PR1012
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62