2012 RENAULT SCENIC programming

13B-429V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 2
VALIDATING THE REGENERATION PROCESS:
At the end of regeneration, a message appears to announce whether the regeneration was successful:
•Particle filter regeneration finished:
Consult PR1012 Weight of soot after regeneration. If this parameter is less than 15 g, the particle filter
regeneration was successful. If PR1012 is greater than 15 g, it is necessary to carry out a second particle filter
regeneration using the diagnostic tool and run command SC017.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool
down for 2 hours with the bonnet open.
Do not carry out an engine oil change before a second After-Sales regeneration.
For Vdiag 28 and 62:
Change the engine oil if requested by a message on the instrument panel.
For the other VDiag:
Consult PR848 Number of regeneration failures. If PR848 is greater than 3, change the engine oil.
Particle filter too full - replace the particle filter: regeneration has failed. The weight of soot in the particle filter
is so great that it is creating a counter pressure. Deal with any faults that appear or replace the particle filter. Run
command SC036: Reinitialise programming and select After particle filter replacement.
For Vdiag 28 and 62:
Change the engine oil if requested by a message on the instrument panel.
For the other Vdiags:
Consult PR848 Number of regeneration failures. If this parameter is greater than 3, it is essential to
change the engine oil.
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-432V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC031
CONTINUED
– If a displayed result is INVALID, the cylinder or injector is not correct.
Difference compared to average ResultsInterpretation of
results
Cylinder XNegative number or
Positive numberINVALIDCarry out the checks
described below.
Run part B of Test 10 Poor injector operation to continue fault finding.
If the result of scenario SC031 is not confirmed, check the engine compressions:
Use a compression gauge and apply command VP036 Fuel supply inhibition (see Interpretation of
commands).
Run compressions on all cylinders.
Are the compressions correct?
Check the cylinder block.Check the fitting of the injector and repair if
necessary.
Otherwise change the injector concerned.
After replacing the injector, follow the
injector code programming procedure (see
Replacement of components), run SC036
Reinitialise programming, and select the
number of the injector replaced.
NOYES
EDC16CP33
Program No.: C4
Vdiag No.: 08, 1C, 20, 24,
26, 28, 34, 38, 4C, 54, 58,
5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-436V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the injectors
– the EGR valve,
– the damper valve,
– after particle filter replacement,
– after particle filter regeneration using the CLIP diagnostic tool,
– after injection computer replacement with no backup option,
– the heater plugs.
Ignition on and engine stopped.
To run this command, select scenario SC036 in the diagnostic tool.
Procedure to be followed:
– on the main screen, select the component to reinitialise after an operation (removal - refitting, regeneration or
replacement of the component),
– select YES then OK to begin reinitialisation,
–Important: when reinitialising injectors, do not forget that cylinder no. 1 is located at the timing end,
– select end on the configuration completed screen to return to the main screen,
– end of operation.
EDC16CP33_V18_SC036 / EDC16CP33_V1C_SC036 / EDC16CP33_V54_SC036 / EDC16CP33_V20_SC036 / EDC16CP33_V58_SC036 /
EDC16CP33_V5C_SC036 / EDC16CP33_V24_SC036 / EDC16CP33_V04_SC036 / EDC16CP33_V08_SC036 / EDC16CP33_V44_SC036 /
EDC16CP33_V4C_SC036 / EDC16CP33_V34_SC036 / EDC16CP33_V38_SC036 / EDC16CP33_V74_SC036 / EDC16CP33_V28_SC036 /
EDC16CP33_V62_SC036 / EDC16CP33_V26_SC036 / EDC16CP33_V60_SC036
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-437V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
RZ005PROGRAMMING
NOTESSpecial notes:
this command enables you to reinitialise the entire computer configuration according to
the vehicle.
Command RZ005 reconfigures the computer.
If the computer does not have any configuration data, use command RZ005 to enter the vehicle options:
– air conditioning,
– Passenger compartment heating resistor,
– cruise control/speed limiter.
These options are detected by the computer even if command RZ005 is not used.
The computer is configured as soon as the one of the vehicle's optional system components is operated.
EDC16CP33_V18_RZ005 / EDC16CP33_V1C_RZ005 / EDC16CP33_V54_RZ005 / EDC16CP33_V20_RZ005 / EDC16CP33_V58_RZ005 /
EDC16CP33_V5C_RZ005 / EDC16CP33_V24_RZ005 / EDC16CP33_V04_RZ005 / EDC16CP33_V08_RZ005 / EDC16CP33_V44_RZ005 /
EDC16CP33_V4C_RZ005 / EDC16CP33_V34_RZ005 / EDC16CP33_V38_RZ005 / EDC16CP33_V74_RZ005 / EDC16CP33_V28_RZ005 /
EDC16CP33_V62_RZ005 / EDC16CP33_V26_RZ005 / EDC16CP33_V60_RZ005
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-438V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
RZ034COMPUTER MEMORY
NOTESIMPORTANT
Only use this command if DF107 Computer memory is Present.
Ignition on and engine stopped.
Command RZ034 reinitialises the computer memory.
With the ignition on:
• Use command RZ034.
• Switch off the ignition and wait for the message Communication lost with computer.
• Switch on the ignition again.
• Run the programming commands (see Configuration and programming).
• Switch off the ignition and wait for the message Communication lost with computer.
Perform a road test to reinitialise the vehicle parameters.
EDC16CP33_V18_RZ034 / EDC16CP33_V1C_RZ034 / EDC16CP33_V54_RZ034 / EDC16CP33_V20_RZ034 / EDC16CP33_V58_RZ034 /
EDC16CP33_V5C_RZ034 / EDC16CP33_V24_RZ034 / EDC16CP33_V04_RZ034 / EDC16CP33_V08_RZ034 / EDC16CP33_V44_RZ034 /
EDC16CP33_V4C_RZ034 / EDC16CP33_V34_RZ034 / EDC16CP33_V38_RZ034 / EDC16CP33_V74_RZ034 / EDC16CP33_V26_RZ034 /
EDC16CP33_V28_RZ034/ EDC16CP33_V60_RZ034 / EDC16CP33_V62_RZ034
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-485
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
IMA*: Individual injector correction
ALP7
CONTINUED
– Check the engine timing (and the
position of the high pressure pump
sprocket).
–Apply part B of Test 10 Poor injector
operation.
Check the lower engine:
– Check the engine mountings.
If the checks are correct, contact the
Techline.If fault DF308 Clogged particle filter is present,
consult the interpretation of DF308.
Run command SC036 Reinitialise programming and
select After particle filter replacement (see
Interpretation of commands).
A
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-494V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST1
CONTINUED
Retighten the particle filter.
Loosen or uncouple the silencer on the side of the
particle filter (see MR 395, 402, 405, 364, 370,
Mechanical, 19B Exhaust, Parts and
consumables for repair).
Start the vehicle and check if the engine runs
better.
Is the engine running normally?Replace the particle filter (see MR 395, 402, 405,
364, 370, Mechanical, 19B, Exhaust, Particle
filter, Removal - Refitting).
Reinitialise the parameters after the particle filter
is replaced.
Run command SC036 Reinitialise
programming and select After particle filter
replacement.
Replace the silencer.
A
YES
NO
YES
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-504V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST10
CONTINUED 1
2. If at least one of these values is X < - 5 mg/stroke
– Check the valve clearance.
– Check the level and condition of the engine oil.
– Remove the injector with the largest adjustment.
– If there is contamination via the diesel, check the condition of the cylinder concerned (cylinder, piston, valves).
– Replace the injector* concerned.
– See paragraph Part C, for confirmation of the fault finding.
3. If at least one of these values does not stabilise (20 seconds after starting):
– Check the low pressure circuit using Test 3 Low pressure circuit test.
– Check the fuel is correct by carrying out Test 12 Diesel fuel conformity check.
See paragraph Part C of Test 10, for confirmation of the fault finding.
After replacing an injector, follow the injector code programming procedure (see Replacement of components),
run SC036 Reinitialise programming and select the number of the injector replaced.
IMPORTANT:
When removing / refitting injectors, follow the cleanliness and safety instructions (see MR 395 (Laguna II ph2),
402 (Vel Satis), 405 (Espace IV Ph2), 364 (Megane II ph2), 370 (Scenic II ph2) Mechanical, 13B, Diesel
injection, Diesel injectors: Removal - Refitting).
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74