2012 RENAULT SCENIC air filter

13B-409V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
rege*: Regeneration
PR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
CONTINUED
In Vdiag 18, 1C, 54:
Each parameter between PR816 and PR825 contains the vehicle distance stored when particle filter regeneration
starts when driving. Each parameter is connected with a status "Regeneration request status record". They are
recorded simultaneously (for example PR819 is associated with ET745 Stored regeneration request status
No. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero, and a new regeneration starts when driving, the distance
information for PR816 is cleared and replaced by the new value.
For other Vdiags:
Each parameter from PR816 Stored regeneration start No. 1 to PR825 Stored regeneration start No. 10
records the mileage when particle filter regeneration starts for which the status request is recorded in ET742
Stored rege*. request status No.1 to ET751 Stored rege*. request status No.10. (for example PR819 Stored
regeneration start No. 4 is associated with ET745 Stored rege*. request status No.4).
Each time a new regeneration when driving is started, the vehicle mileage is recorded in PR816, as well as its
status in ET742.
PR816 to PR825 operate through successive copying (when regeneration starts, the value of PR816 is copied to
PR817 Stored regeneration start no. 2, the value of PR817 is copied to PR818 Stored regeneration start no. 3
and so on).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-421
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$130.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR1012WEIGHT OF SOOT AFTER REGENERATION
STATUS
DEFINITIONThis parameter indicates the weight in g of soot present in the particle filter following
regeneration.
NOTESThis parameter should be consulted after running SC017 Particle filter regeneration.
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80°C without electrical consumers
If this parameter is less than 15 g, particle filter regeneration was successful.
If PR1012 is greater than 15 g, it is necessary to perform a second particle filter regeneration using command
SC017 Particle filter regeneration.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool down
for 2 hours with the bonnet open.
Do not carry out an engine oil change before a second After-Sales regeneration.
EDC16CP33_V1C_PR1012 / EDC16CP33_V54_PR1012 / EDC16CP33_V20_PR1012 / EDC16CP33_V58_PR1012 /
EDC16CP33_V5C_PR1012 / EDC16CP33_V24_PR1012 / EDC16CP33_V28_PR1012 / EDC16CP33_V62_PR1012/
EDC16CP33_V26_PR1012 / EDC16CP33_V60_PR1012
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62

13B-427V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017PARTICLE FILTER REGENERATION
NOTESOnly run this command after interpretation of the following faults:
– DF308 Clogged particle filter,
– DF311 Failed regenerations limit exceeded,
– df312: speed request.
WARNING:
– It is essential to observe the health and safety guidelines (see MR364 (Mégane II ph2), MR370 (Scénic II ph2),
MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2) Mechanical, 19B, Exhaust, Particle
filter: Cleaning) and follow the procedure below.
SAFETY INSTRUCTIONS TO BE FOLLOWED:
The regeneration causes exhaust fumes and high temperatures.
It is strongly recommended that you put the vehicle outside during regeneration.
If it is not possible to carry out regeneration outside, use an extractor fan that can withstand the very high
regeneration temperatures (400°C at the exhaust outlet).
Perform regeneration on a surface free from fire risks (oil, dry leaves, etc.).
Nothing should be left in the vicinity of the exhaust pipe.
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
WARNING:
Check the engine oil level before running the command to avoid any engine racing. The oil level must be
between the minimum level and the middle level on the oil dipstick.
Before performing a particle filter regeneration, it is essential to deactivate the air conditioning
compressor (risk of engine damage) and all the electrical consumers.
IF NECESSARY:
Regeneration can be stopped by pressing the engine start button twice briefly (less than 3 seconds).
Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes) Communication
lost with computer: EDC16 C33, check the tool connection and the computer power supply before
switching the ignition back on.
EDC16CP33_V1C_SC017 / EDC16CP33_V54_SC017 / EDC16CP33_V20_SC017 / EDC16CP33_V58_SC017 / EDC16CP33_V5C_SC017 /
EDC16CP33_V24_SC017 / EDC16CP33_V28_SC017 / EDC16CP33_V62_SC017/ EDC16CP33_V26_SC017 / EDC16CP33_V60_SC017
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-428V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 1
PROCEDURE TO BE FOLLOWED:
To run this command, select the command mode on the diagnostic tool and run command SC017.
When regeneration is complete, a message will indicate whether regeneration was successful, and what
operations need to be carried out (filter replacement, whether an oil service is required, etc.).
DESCRIPTION OF THE PROCESS
particle filter regeneration takes place in 3 stages (values given as a guide only):
Heating phase: the speed is fixed or fluctuating around 3000 rpm.
– This phase lasts at least 6minutes, until the coolant temperature is above 80°C.
–Regeneration phase: the speed is fixed or varies around 2000 rpm. Engine injection is retarded. The exhaust
fumes rise in temperature and burn the soot retained in the particle filter. The particle filter downstream
temperature starts to rise after the particle filter upstream temperature due to the volume of the particle filter.
Then the combustion of the soot stored in the particle filter causes the particle filter downstream temperature
to increase, possibly reaching more than 700°C depending on the amount of soot in the filter (with a particle
filter upstream temperature of around 600°C). This phase lasts about 30 minutes.
–Cooling phase: the engine speed is fixed or varies around 2000 rpm.
– Engine injection returns to normal and the exhaust gases cool the particle filter.
– This phase lasts 3 minutes. At the end of this period, the engine speed returns to idle speed or remains fixed
at 2000 rpm.
The process lasts at least 40 minutes (the regeneration time will be increased depending on how long it takes
for the coolant to heat up to 80°C).
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-429V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 2
VALIDATING THE REGENERATION PROCESS:
At the end of regeneration, a message appears to announce whether the regeneration was successful:
•Particle filter regeneration finished:
Consult PR1012 Weight of soot after regeneration. If this parameter is less than 15 g, the particle filter
regeneration was successful. If PR1012 is greater than 15 g, it is necessary to carry out a second particle filter
regeneration using the diagnostic tool and run command SC017.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool
down for 2 hours with the bonnet open.
Do not carry out an engine oil change before a second After-Sales regeneration.
For Vdiag 28 and 62:
Change the engine oil if requested by a message on the instrument panel.
For the other VDiag:
Consult PR848 Number of regeneration failures. If PR848 is greater than 3, change the engine oil.
Particle filter too full - replace the particle filter: regeneration has failed. The weight of soot in the particle filter
is so great that it is creating a counter pressure. Deal with any faults that appear or replace the particle filter. Run
command SC036: Reinitialise programming and select After particle filter replacement.
For Vdiag 28 and 62:
Change the engine oil if requested by a message on the instrument panel.
For the other Vdiags:
Consult PR848 Number of regeneration failures. If this parameter is greater than 3, it is essential to
change the engine oil.
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-430V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 3
–Particle filter regeneration failed: regeneration failed because the temperature upstream of the turbine is too
low. Apply Test 11 Temperature upstream of turbine too low.
In all cases, carry out the following operations:
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes) Communication
lost with computer: EDC16 CP33, check the tool connection and the computer supply,
– switch on the ignition and establish dialogue with the injection computer,
– run command SC036,
– depending on the operation carried out, select After particle filter regeneration with the diagnostic tool or
After particle filter replacement,
–switch off the ignition and wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue
with the computer: EDC16 CP33, check the tool connection and the computer supply voltage,
– then switch on the ignition again,
clear the present or stored faults from the computer memory (operation to be carried out within 3 minutes of
switching on the ignition).
Note:
Always change the engine oil and the oil filter in the following cases:
• following an After-Sales regeneration only if requested by a message on the CLIP diagnostic tool,
• after particle filter replacement following DF311 Number of failed regenerations exceeded,
– after a second regeneration (when two successive regenerations).
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-434V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC035
CONTINUED 1
Interpretation of incorrect results:
– Is one of the value definitions for the various displayed stages is “TOO SLOW” or “TOO FAST”, see the
following table:
STEP X
(X is the variable
from 1 to 4)Rail pressure Raise
timeRail pressure Dump
timeInterpretation of
results
STEP X TOO SLOW TOO SLOW Check 1
STEP X TOO SLOW TOO FAST Check 2
STEP X TOO SLOW OK Check 3
STEP X OK TOO SLOW Check 4
STEP X OK TOO FAST Check 5
STEP 5 TOO FAST Check 5
Explanation of results interpretation:
Check 1:
–Apply Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit leaks.
–Apply Test 3 Low pressure circuit check.
– Replace the high pressure pump.
Check 2:
–Apply Test 10.
–Apply ALP6.
– Apply the part of Test 3 concerning the fuel filter.
– Replace the high pressure pump.
– Check the injector return flow and the injectors.
– Check the rail pressure regulator by running command AC225 Rail pressure regulator.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-436V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the injectors
– the EGR valve,
– the damper valve,
– after particle filter replacement,
– after particle filter regeneration using the CLIP diagnostic tool,
– after injection computer replacement with no backup option,
– the heater plugs.
Ignition on and engine stopped.
To run this command, select scenario SC036 in the diagnostic tool.
Procedure to be followed:
– on the main screen, select the component to reinitialise after an operation (removal - refitting, regeneration or
replacement of the component),
– select YES then OK to begin reinitialisation,
–Important: when reinitialising injectors, do not forget that cylinder no. 1 is located at the timing end,
– select end on the configuration completed screen to return to the main screen,
– end of operation.
EDC16CP33_V18_SC036 / EDC16CP33_V1C_SC036 / EDC16CP33_V54_SC036 / EDC16CP33_V20_SC036 / EDC16CP33_V58_SC036 /
EDC16CP33_V5C_SC036 / EDC16CP33_V24_SC036 / EDC16CP33_V04_SC036 / EDC16CP33_V08_SC036 / EDC16CP33_V44_SC036 /
EDC16CP33_V4C_SC036 / EDC16CP33_V34_SC036 / EDC16CP33_V38_SC036 / EDC16CP33_V74_SC036 / EDC16CP33_V28_SC036 /
EDC16CP33_V62_SC036 / EDC16CP33_V26_SC036 / EDC16CP33_V60_SC036
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.