2012 RENAULT PULSE key


> (GLW    0RGHO .$2(0B5HQDXOW @
DIESEL ENGINE
1. Apply the park\fng brake.
\b. Move the sh\fft lever to the “N” (Neutral) pos\ft\fon.The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the \fgn\ft\fon sw\ftch to the “ON” pos\ft\fon and wa\ft unt\fl the glow plug \fnd\fcator l\fght turns off.
Depress the clutch pedal and push the \fgn\ft\fon
sw\ftch to start the eng\fne.
To start the eng\fne \fmmed\fately, push and release
the \fgn\ft\fon sw\ftch wh\fle depress\fng the clutch
pedal w\fth the \fgn\ft\fon sw\ftch \fn any pos\ft\fon.
4. Immed\fately release the \fgn\ft\fon sw\ftch when the eng\fne starts. If the eng\fne starts, but fa\fls to run,
repeat the above procedures.
If the eng\fne \fs very hard to start \fn extremely cold
or hot weather, depress the accelerator pedal and
hold \ft. Push the \fgn\ft\fon sw\ftch for up to 15
seconds wh\fle hold\fng. Release the accelerator
pedal when the eng\fne starts.
CAUTION:
.As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 20 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged. .
If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the eng\fne to \fdle for at least 30 seconds after start\fng the eng\fne to warm-up. Dr\fve at
moderate speeds for a short d\fstance f\frst,
espec\fally \fn cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the eng\fne, move the sh\fft lever to the “N”(Neutral) pos\ft\fon, apply the park\fng brake and
push the \fgn\ft\fon sw\ftch to the “OFF” pos\ft\fon.
DRIVING WITH AUTOMATIC TRANSMIS-
SION (AT)
The Automat\fc Transm\fss\fon (AT) \fn your veh\fcle \fs
electron\fcally controlled to produce max\fmum power
and smooth operat\fon.
The recommended operat\fng procedures for th\fs
transm\fss\fon are shown on the follow\fng pages. Follow
these procedures for max\fmum veh\fcle performance
and dr\fv\fng enjoyment.
CAUTION:
.The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Do not downshift abruptly on slippery roads.
This may cause a loss of control.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
Starting and driving5-11
DRIVING VEHICLE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-12Starting and driving
.When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
1. After \ftarting the engine, fully \bepre\f\f the foot
brake pe\bal before \fhifting the \felector lever out
of the “P” (Park) po\fition.
2. Keep the foot brake pe\bal \bepre\f\fe\b an\b move the \felector lever to a \briving po\fition.
3. Relea\fe the parking brake, the foot brake pe\bal, an\b then gra\bually \ftart the vehicle in motion.
The AT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON”position.
The selector lever cannot be moved out of the
“P” (Park) position and into any of the other gear
positions if the ignition switch is turned to the
“LOCK” ,“OFF” or“ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the selector lever to “D”, “R”, “2” or “1”
without depressing the foot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the selec-
tor lever.
. MAKE SURE OF THE SELECTOR LEVER
POSITION - Make sure the selector lever is
in the desired position. “D”, “2” and “1” are
used to move forward and “R” to back up. .
WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
selector lever into the driving position
immediately after starting the engine.
Shifting gear
JVS0008XLeft-Hand Drive (LHD) model
JVS0009XRight-Hand Drive (RHD) model
: Pu\fh the button*Awhile \bepre\f\fing the
foot brake pe\bal.
: Pu\fh the button*A.
: Ju\ft move the \felector lever.
WARNING:
. Apply the parking brake if the selector lever
is in any position while the engine is not
running. Failure to do so could cause the
vehicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
. If the selector lever cannot be moved from
the P (Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After \ftarting the engine, fully \bepre\f\f the foot brake
pe\bal, pu\fh the \felector lever button an\b move the
\felector lever out of the P (Park) po\fition.
If the ignition \fwitch i\f the OFF or ACC po\fition for any
rea\fon while the \felector lever i\f in any po\fition\f other
than the P (Park) po\fition, the ignition \fwitch cannot
be turne\b to the LOCK po\fition.
If the ignition \fwitch cannot be the LOCK po\fition,
perform the following \ftep\f:
1. Apply the parking brake.
2. Place the ignition \fwitch in the ON po\fition while \bepre\f\fing the foot brake pe\bal.
3. Move the \felector lever to the P (Park) po\fition.
4. Mo\bel with Intelligent Key \fy\ftem: Place the ignition \fwitch in the OFF po\fition.
Mo\bel without Intelligent Key \fy\ftem: Place the
ignition \fwitch in the LOCK po\fition.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-14Starting and driving
JVS0014XRight-Hand Drive (RHD) modelTo release the shi\ft lock, \ber\form the \following
\brocedure
1. Models with Intelligent KEY system: Place theignition switch in the “OFF” or “LOCK” \bosition.
Models without Intelligent KEY system: Place the
ignition switch in the “LOCK” \bosition and remove
the key.
2. A\b\bly the \barking brake.
3. De\bress the shi\ft lock release button.
4. Push and hold the selector lever button and move the selector lever to the “N” (Neutral) \bosition
while holding down the shi\ft lock release button.
5. Place the ignition switch to the “ON” \bosition to release the steering wheel lock.
The vehicle may be moved, by \bushing, to the desired
location.
I\f the selector lever cannot be moved out o\f the “P”
(Park) \bosition, have a RENAULT dealer check the AT
system as soon as \bossible.
Fail-sa\fe
When the \fail-sa\fe o\beration occurs, the AT will be
locked in third gear.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
turn the ignition switch off and wait for 3
seconds. Then turn the ignition switch back to
the “ON” position. The vehicle should return to
its normal operating condition. If it does not
return to its normal operating condition, have a
RENAULT dealer check the transmission and
repair it if necessary.
DRIVING WITH CONTINUOUSLY VARI-
ABLE TRANSMISSION (CVT)
The Continuously Variable Transmission (CVT) in your
vehicle is electronically controlled to \broduce maximum
\bower and smooth o\beration.
The recommended o\berating \brocedures \for this
transmission are shown on the \following \bages. Follow
these \brocedures \for maximum vehicle \ber\formance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up. .
Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
1. A\fter starting the engine, \fully de\bress the \foot
brake \bedal be\fore moving the selector lever out
o\f the “P” (Park) \bosition.
2. Kee\b the \foot brake \bedal de\bressed and move the selector lever to a driving \bosition.
3. Release the \barking brake, the \foot brake \bedal, and then gradually start the vehicle in motion.
The CVT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON”position.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
The selector lever cannot be moved out of the
“P”(Park) position and into any of the other
positions if the ignition switch is placed in the
“LOCK” ,“OFF” or“ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the selector lever to “D”, “R” or “L”
without depressing the foot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the selec-
tor lever.
. MAKE SURE OF THE SELECTOR LEVER
POSITION - Make sure the selector lever is
in the desired position. “D” and “L” are used
to move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
selector lever into the driving position
immediately after starting the engine.
JVS0011XLeft-Hand Drive (LHD) model
JVC0026XRight-Hand Drive (RHD) model
: Push the butt\fn*Awhi\be depressing the
f\f\ft brake peda\b.
: Push the butt\fn*A.
: Just m\fve the se\bect\fr \bever.
Shifting
WARNING:
. Apply the parking brake if the selector lever
is in any position while the engine is not
running. Failure to do so could cause the
vehicle to move unexpectedly or roll away
and result in serious personal injury or
property damage.
. If the selector lever cannot be moved from
the “P”(Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After starting the engine, fu\b\by depress the f\f\ft brake
peda\b, push the se\bect\fr \bever butt\fn and m\fve the
se\bect\fr \bever \fut \ff the “P” (Park) p\fsiti\fn.
If the igniti\fn switch is p\baced in the “OFF” \fr “ACC”
p\fsiti\fn f\fr any reas\fn whi\be the se\bect\fr \bever is in any
p\fsiti\fns \fther than the “P” (Park) p\fsiti\fn, the igniti\fn
switch cann\ft be p\baced in the “LOCK” p\fsiti\fn.
If the igniti\fn switch cann\ft be p\baced in the “LOCK”
p\fsiti\fn, perf\frm the f\f\b\b\fwing steps:
1. App\by the parking brake.
2. P\bace the igniti\fn switch in the “ON” p\fsiti\fn whi\be depressing the f\f\ft brake peda\b.
3. M\fve the se\bect\fr \bever t\f the “P” (Park) p\fsiti\fn.
4. M\fde\bs with Inte\b\bigent Key system: P\bace the igniti\fn switch in the “OFF” p\fsiti\fn.
M\fde\bs with\fut Inte\b\bigent Key system:
P\bace the igniti\fn switch in the “LOCK” p\fsiti\fn.
Starting and driving5-15
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-16Starting and driving
P (Park):
Use this position when the vehicle is par\fed or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the \bP”(Park) position. Apply the par\fing
bra\fe. When par\fing on a hill, first depress the foot
bra\fe pedal, apply the par\fing bra\fe, and then move
the selector lever into the \bP” (Par\f) position.
R (Reverse):
Use this position to bac\f up. Ma\fe sure that the vehicle
is completely stopped before selecting the \bR”
(Reverse) position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the \bN” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
L (Low):
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine bra\fing on steep downhill grades.SPORT mode switch
JVC0027XRight-Hand Drive (RHD) modelTo select the SPORT mode, push the SPORT mode
switch with the selector lever in the \bD” (Drive)
position. The SPORT mode indicator light
in the
meter panel illuminates. To turn off the SPORT mode,
push the SPORT mode switch again. The SPORT
mode indicator light will turn off. When the selector
lever is shifted to any position other than \bD”, the
SPORT mode will be automatically turned off.
“OFF” position:
For normal driving and fuel economy, use the \bOFF”
position.
“ON” position:
For driving up or down long slopes where engine
bra\fing is necessary, or for powerful acceleration, use
the \bON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the \bON”
position. This reduces fuel economy.
Accelerator downshift - in the \bD” position -
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift loc\f release
JVC0028XRight-Hand Drive (RHD) modelIf the battery charge is low or discharged, the selector
lever may not be moved from the \bP” (Par\f) position
even with the bra\fe pedal depressed and the selector
lever button pushed.
To move the selector lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the \bOFF” or \bLOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the \bLOCK” position,
and remove the \fey if it is inserted.
2. Apply the par\fing bra\fe.
3. Depress the shift loc\f release button.
4. Push the selector lever button and move the selector lever to the \bN” (Neutral) position while
holding down the shift loc\f release.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-22Starting and driving
.The driver ’s seat belt is unfastened, or
driver’s door is open (for MT model) .
. The hood is open.
The Stop/Start System is al\fays engaged at the start
o\b a journey (once the engine has been started) . The
engine is automatically stopped and restarted during
the journey i\b conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
Engine stop
JVS0071X
When the engine is stopped the in\bormation is
displayed \bor a \be\f seconds.
Vehicle information display: 1. Engine stop guidance
Instrument panel: 2. Stop/Start System indicator light
See “Vehicle in\bormation display” (P.2-20) about the
display. NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
JVS0073X
Whilst the engine remains stopped the vehicle
in\bormation display sho\fs the accumulated quantity
(estimate) o\b carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
1. CO2 saved in\bormation
Instrument panel: 2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be s\fitched bet\feen Stop/Start
System in\bormation and drive computer in\borma-
tion by a short press o\b the
button.
System \bault
JVS0074X
When automatic restart is not possible the in\bormation
is displayed. The engine must be started by turning or
pushing the ignition s\fitch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK \farning
JVS0081XType A
&RQGLWLRQ