2012 RENAULT PULSE phone


> (GLW    0RGHO .$2(0B5HQDXOW @
4-40Heater and air conditioner, and audio system
After selecting the preferred language\f push the
ENTE\b button to exit the menu.
To configure the SPEED volume and BEEP settings\f
perform the following procedure:
1. Push the MENU button.
2. Turn the Volume control dial clockwise or counter- clockwise. The display message will change as
follows:
SPEED VOL ⇔CLOCK ⇔BEEP
. When SPEED VOL appears on the display\f briefly
push the ENTE\b button then turn the VOLUME
control dial clockwise or counterclockwise to
adjust the level of the volume.
Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed
volume setting results in the audio volume
increasing more rapidly with vehicle speed. Push
the ENTE\b button again to save the setting.
. When BEEP appears on the display\f briefly push
the ENTE\b button and then turn the VOLUME
control dial clockwise or counterclockwise to
switch the beep sound on or off. Push the ENTE\b
button again to save the setting.
After the preferred levels have been set\f push the
MENU button to exit the menu or wait at least for 10
seconds without pressing any buttons.
For clock adjustments\f see “Audio main operation”
(P.4-36) .LW-MW-FM \bADIO WITH COMPACT DISC (CD) CHANGE\b (Type F)
JVH0044X
1. CD LOAD button
2. POWE\b ON/OFF button
3. PHONE SEND button
4. TA (Traffic Announcement)/NEWS button
5. \badio band select button
6. \badio memory/CD select buttons
7. CD button
8. AUX button 9. Sound preference button
10. MENU button
11. CD EJECT button
12. SEEK/T\bACK button
13. PHONE BOOK button
14. PHONE END/BACK button
15. VOLUME control/MENU select knob
16. ENTE\b button
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
17. AUX IN (auxiliary input\f jack
1\b. RPT (Repeat\f/MIX (Mix play\f button
19. TUNE/SEARCH button
Anti-theft system (if equipped\f
This unit can only be activated when the ignition switch
for Anti-Theft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
To turn on the audio system, push the POWER ON/
OFF button.
.The system will turn on in the mode, (radio or CD\f
which was used immediately before the system
was last turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the POWER ON/
OFF button.
Volume control:
To control the volume, turn the VOLUME control dial.
Turn the VOLUME control dial clockwise to increase
the audio volume.
Turn the VOLUME control dial counterclockwise to
decrease the audio volume.
Sound preference button:
To enter the audio mode (radio or CD\f , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode.
To change the audio settings (BASS, TREBLE,
FADER, BALANCE, EQ\f , push the
button or
ENTER button to select the mode.
BASS ?TREBLE ?BALANCE ?FADER ?EQ ?
BASS
To adjust each audio setting, turn the MENU/VOL
control dial clockwise or counterclockwise.
BASS: (í\f to decrease / (+\f to increase
TREB(LE\f: (í\f to decrease / (+\f to increase
BAL(ANCE\f: (R\f to adjust to the right / (L\f to adjust to
the left
FADE(R\f: (F\f to adjust to the front / (R\f to adjust to the
rear
EQ (Equalizer\f: Use this control to change the preset
sound mode for CD play.
Turn the MENU/VOL dial clockwise or counterclock-
wise. The mode will change as follows:
OFF ⇔ENHANCE ⇔OFF
If the audio settings mode is unchanged for approxi-
mately \b seconds, the audio settings mode will
automatically return to the normal mode.
Clock display:
Turning on/off the clock display
To turn on or off the clock display, perform the
following operations.
1. Push the MENU button while the audio system is on. ("PHONE SETUP" is displayed.\f 2. Turn the VOLUME control knob until "CLOCK"
appears on the display.
3. Push the ENTER button. ("CLOCK OFF" or "CLOCK ON" is displayed.\f
4. To turn on the clock display, turn the VOLUME control knob till "CLOCK ON" is displayed. To turn
off the clock display, turn the VOLUME control
knob till "CLOCK OFF" is displayed, and push
ENTER.
Clock adjustment
To adjust the time of the clock, perform the following
operations.
1. Push the ENTER button while "CLOCK ON" is displayed.
2. The hour display will flash.
3. Turn the VOLUME control knob to adjust the hour.
4. Push the ENTER button. The minute display will flash.
5. Turn the VOLUME control knob to adjust the minute.
6. Push the ENTER button to complete the clock adjustment.
AUX button:
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, MP3 player or laptop computer.
Push the AUX button to play a compatible device when
it is plugged into the AUX IN jack.
RENAULT strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
Heater and air conditioner, and audio system4-41
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
station and the actual playing mode will be interrupted\f
Once the news broadcast is finished, the unit returns
to the pre\bious mode\f
In some countries or regions, this ser\bice is not
a\bailable or the signal is too weak to be recei\bed\f
1\fNews standby mode
.The news standby mode can be acti\bated in
the FM or CD mode\f
.A news interruption will be announced and“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations\f The display will then change
to the PS name of the interrupting station\f
.When pushing the TA/NEWS button for longerthan 2 seconds, the news standby mode is
turned off and the indicator disappears from
the display\f
2\f News interruption mode
.When the TA/NEWS button is pushed during
the news interruption mode, the radio returns to
the pre\bious source\f Howe\ber, the news
standby mode is maintained\f
.When thebutton is pushed during the
news interruption mode, the radio changes to
the CD mode\f Howe\ber, the news standby
mode is maintained\f
If the radio band is changed to the MW or LW,
the news standby mode will be turned off\f
MENU button:
To configure Alternati\be Frequency, Regional and
Language settings, perform the following procedure:
1\f Push and hold the MENU button for at least 1\f5 seconds\f 2\f Turn the MENU/VOL dial clockwise or counter-
clockwise\f The display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. To acti\bate or deacti\bate the AF and REG mode,
briefly push the ENTER button when AF or REG
appears on the display and turn the MENU/VOL
dial clockwise or counterclockwise to switch
between the off or on position\f After selection,
push the ENTER button to confirm the settings\f
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak\f
— When the REG mode is enabled, the audio unit will maintain and maintain the station which is
broadcasting local (regional) programmes\f
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the MENU/VOL dial clockwise or
counterclockwise to select the appropriate lan-
guage setting\f
ENGLISH ⇔DUTCH ⇔FRENCH ⇔SPANISH
⇔ GERMAN ⇔ITALIAN ⇔PORTUGUESE ⇔
ENGLISH
After selecting the preferred language, push the
ENTER button to exit the menu\f
To configure the SPEED \bolume and BEEP settings,
perform the following procedure:
1\f Push the MENU button\f
2\f Turn the MENU/VOL dial clockwise or counter- clockwise\f The display message will change as
follows:
PHONE SETUP ⇔SPEED VOL ⇔CLOCK ⇔
BEEP ⇔PHONE SETUP
For phone operation, see “Bluetooth
ŠHands-Free Phone System (if equipped for model without
na\bigation system)” (P\f4-56) \f
. When SPEED VOL appears on the display, briefly
push on the ENTER button then turn the MENU/
VOL dial clockwise or counterclockwise to adjust
the le\bel of the \bolume\f
Adjusting the setting to 0 (zero) turns off the
speed \bolume feature\f Increasing the speed
\bolume setting results in the audio \bolume
increasing more rapidly with \behicle speed\f Push
the ENTER button again to sa\be the setting\f
. When BEEP appears on the display, briefly push
the ENTER button and then turn the MENU/VOL
dial clockwise or counterclockwise to switch the
beep sound on or off\f Push the ENTER button
again to sa\be the setting\f
After the preferred le\bels ha\be been set, push the
MENU button to exit the menu or wait at least for 10
seconds without pressing any buttons\f
Heater and air conditioner, and audio system4-45
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
* iPod and iPhone are trademarks of Apple In\f.,
registered in the \b.S. and other \fountries.
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
.Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
(Some USB devices come with a
mark as a guide. Make sure that the mark
is facing the correct direction before insert-
ing the device.)
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to your devi\fe manufa\fturer’s owner information
regarding the proper use and \fare of the devi\fe.
Compatibility:
The following models are supported:
. Third generation iPhone (Firmware version
IOS4/4.0)
. Fourth generation iPhone (Firmware version
IOS4/4.0) .
Fifth generation iPod (Firmware version 1.3)
. First generation iPod Classi\f (Firmware version
1.1.1 or 1.1.2PC)
. Se\fond generation iPod Classi\f (Firmware ver-
sion 2.0.1)
. First generation iPod tou\fh (Firmware version
1.1.5 or 2.2.1)
. Se\fond and third generation iPod tou\fh (Firm-
ware version 2.2.1 or IOS4/4.0.0)
. First generation iPod nano (Firmware version
1.3.1)
. Se\fond generation iPod nano (Firmware version
1.1.3)
. Third generation iPod nano (Firmware version
1.1.2PC or 1.1.3PC)
. Fourth generation iPod nano (Firmware version
1.0.2 or 1.0.4)
. Fifth generation iPod nano (Firmware version 1.0.1
or 1.0.2)
The iPod tou\fh may not respond qui\fkly to the system
in some \fases.
Make sure that the iPod firmware is updated.
Operating tips:
. iPod Shuffle and iPod mini are not supported.
. Some iPod operations may not be available with
this system.
AUX button:
To operate the iPod use one of the following methods:
. Push the
button and then turn the T\bNE/
MEN\b/ENTER dial for the \bSB item. On\fe
highlighted, push the T\bNE/MEN\b/ENTER dial. .
Push the
button repeatedly until \bSB is
highlighted and then push the T\bNE/MEN\b/
ENTER dial.
Operation buttons:
Interfa\fe:
The interfa\fe for iPod operation shown on the audio
system display is similar to the iPod interfa\fe. \bse the
T\bNE/MEN\b/ENTER dial to play a tra\fk on the iPod.
The following items \fan be \fhosen from the menu list
s\freen.
. Playlists
. Artists
. Albums
. Tra\fks
. Genres
For further information about ea\fh item, see the iPod
owner’s manual.
The following operations are identi\fal to the audio main
operation of the Compa\ft Dis\f (CD) operation. For
details, see “CD player operation” (P.4-48) .
. List view
. Qui\fk sear\fh
.
. MIX (Random play)
. RPT (Repeat tra\fk)
. Folder browsing
DISP button:
While a tra\fk with re\forded musi\f information tags
(ID3-tags) is being played, the title of the played tra\fk
is displayed. If the tags are not provided then a
notifi\fation message is displayed.
When the
button is pushed repeatedly, further
Heater and air conditioner, and audio system4-51
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-52Heater and air conditioner, and audio system
information about the track can be di\fplayed alon\b
with the track title a\f follow\f:
Track time?Arti\ft ?Album ?Folder name ?Track
time
Track detail\f:
By pu\fhin\b and holdin\b the
button the di\fplay will
\fhow a detailed overview and after a few \fecond\f it
will return to the main di\fplay. Pu\fh the
button
briefly to return to the main di\fplay immediately.
BluetoothŠaudio player operation
Regulatory information:
BluetoothŠi\f a trademark owned
by Bluetooth SIG, Inc., and
licen\fed to Daewoo IS Corp.
CE statement:
Hereby Daewoo IS Corp. declare\f that thi\f \fy\ftem i\f
in compliance with the e\f\fential requirement\f and
other relevant provi\fion\f of Directive 1999/5/EC.
NOTE:
The audio system only supports BluetoothŠ
devices with AVRCP (Audio Video Remote Con-
trol Profile) version 1.3, 1.0, or earlier.
Bluetooth
Šaudio player setting:
To \fet up the BluetoothŠ\fy\ftem with your preferred
device, pu\fh thebutton and \felect BluetoothŠ,
and then pu\fh the TUNE/MENU/ENTER dial or
alternatively, pu\fh the
button. The followin\b item\f
are available: .
Pair Device
Bluetooth
Šdevice\f can be paired with the \fy\ftem.
A maximum of 5 device\f can be re\bi\ftered.
. Select Device
Paired Bluetooth
Šdevice\f are li\fted and can be
\felected for connection.
. Delete Device
A re\bi\ftered Bluetooth
Šdevice can be deleted.
. Bluetooth
If thi\f \fettin\b i\f turned off, the connection between
the Bluetooth
Šdevice\f and the in-vehicle Blue-
toothŠmodule will be cancelled.
Pair Device:
1. Pu\fh the
button. Select the “Bluetooth” key
by turnin\b the TUNE/MENU/ENTER dial, and then
pu\fh the TUNE/MENU/ENTER dial.
You can re\bi\fter up to 5 different Bluetooth
Š
audio/cellular phone device\f. However, you can
only u\fe one device at a time. If you have 5
different Bluetooth
Šdevice\f, a newly re\bi\ftered
device can only replace one of the already
re\bi\ftered 5 exi\ftin\b paired device\f. U\fe the
“Delete Device” key to delete one of the exi\ftin\b
paired device\f.
2. Select the “Pair Device” key. The pairin\b procedure depend\f on the connected device:
.Cellular phone:
The me\f\fa\be Ready to Pair Pin:1234 will be
di\fplayed.
.Audio device without PIN code:The BluetoothŠconnection will be automati-
cally connected without any further input.
.Audio device with PIN code:
A new \fcreen will appear. A\f\fi\bn the 4 di\bit
PIN code by turnin\b the TUNE/MENU/ENTER
dial to each di\bit of the code and pu\fhin\b the
TUNE/MENU/ENTER dial to confirm each di\bit.
After the PIN code i\f input, \felect “Validate”
and pu\fh the TUNE/MENU/ENTER dial. The
Bluetooth
Šconnection will be made.
The 4-di\bit PIN code i\f provided with the audio
device, \fee the owner’\f manual of the audio
device.
3. On Bluetooth
Šaudio/cellular phone device\f:
a. Check that BluetoothŠi\f turned on, on your
device.
b. Switch to the \fearch mode for Bluetooth
Š
device\f. If the \fearch mode find\f a device it
will be \fhown on the device di\fplay. Select My
Car.
c. Enter the number code \fhown on the relevant device with the device’\f own keypad, and pu\fh
the confirmation key on the device it\felf. Refer
to the relevant Bluetooth
Šdevice owner’\f
manual for further detail\f.
When the device i\f \fucce\f\ffully paired a notification
me\f\fa\be will be di\fplayed, and then the audio \fy\ftem
di\fplay will return to the current audio \fource di\fplay.
Durin\b connection the followin\b \ftatu\f icon\f will be
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
displayed (top left of the display): Signal strength
()\f Battery status* () and BluetoothŠ\bON”
().
*: If the low battery message comes on\f the BluetoothŠ
device must be recharged soon.
The pairing procedure and operation may vary
according to device type and compatibility. See the
owner’s manual of the Bluetooth
Šdevice for further
details.
Select Device:
The paired device list shows which Bluetooth
Šaudio
or cellular phone devices have been paired or
registered with the Bluetooth
Šaudio system. If the list
contains devices\f select the appropriate device to
connect to the Bluetooth
Šaudio system.
The following symbols indicate the capability of the
registered device:
.
: cellular phone integration
.
: Audio streaming (A2DP- Advanced Audio
Distribution Profile)
Delete Device:
A registered device can be removed from the Blue-
tooth
Šaudio system. Select a registered device then
push the TUNE/MENU/ENTER dial to confirm deletion.
Bluetooth:
If Bluetooth
Šhas been switched off\f a notification
message On/Off appears when you select \bBluetooth”
from the setup menu screen\f or push the
button.
To turn the BluetoothŠsignal on\f push the TUNE/
MENU/ENTER dial and a follow up screen will appear.
Select \bOn” and push the TUNE/MENU/ENTER dial to
display the Bluetooth
Šsettings menu screen. Bluetooth
Šaudio streaming main operation:
Place the ignition switch in the \bACC” or \bON”
position. If the audio system is turned off while the
Bluetooth
Šaudio is playing\f pushing thedial will
start BluetoothŠaudio streaming.
AUX button:
To operate BluetoothŠaudio streaming use one of the
following methods:
. Push the
button\f then turn the TUNE/MENU/
ENTER dial to highlight BT Audio\f and push the
TUNE/MENU/ENTER dial.
. Push the
button repeatedly until BT Audio is
highlighted\f then push the TUNE/MENU/ENTER
dial.
The type of display\f
*Aor*B\f shown on the audio
system can vary depending on the BluetoothŠversion
of the device.
Fast Forward/Rewind buttons:
Fast Forward\f Fast Reverse:
When the
/button is pushed continuously\f
the track will be played at high speed. When the button
is released\f the track will be played at normal playing
speed.
Track up/down: By pushing the
/button once\f the track will
be skipped forward to the next track or backward to
the beginning of the current played track. Push the
/button more than once to skip through the
tracks.
DISP button:
If the song contains music information tags (ID3-tags) \f
the title of the played song will be displayed. If tags are
not provided\f the display will not show any messages.
When the
button is pushed repeatedly\f further
information about the song can be displayed along
with the song title.
By pushing and holding the
button the display will
show a detailed overview which after a few seconds
will return to the main display. Push the
button
briefly to return to the main display immediately.
Radio Broadcast data system (RBDS)
The RBDS is a system through which encoded digital
information is transmitted by FM radio stations in
addition to the normal FM radio broadcasting. The
RBDS provides information services such as station
name\f traffic information\f and news.
NOTE:
In some countries or regions, some of these
services may not be available.
Alternative Frequency (AF) mode:
The AF mode operates in the FM (radio) mode.
. The AF mode operates both in the FM (radio) and
CD mode (if FM was previously selected in the
radio mode) .
. The AF function compares signal strengths and
selects the station with the optimum reception
conditions for the currently tuned-in station.
Heater and air conditioner, and audio system4-53
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-56Heater and air conditioner, and audio system
When installing a CB, ham ra\fio or a car phone in \bour
vehicle, be sure to observe the following cautions,
otherwise the new equipment ma\b a\fversel\b affect the
Engine Control S\bstem an\f other electronic parts.
CAUTION:
.Keep the antenna as far away as possible
from the Electronic Control Module.
. Keep the antenna wire at least 20 cm (8 in)
away from the Engine Control harnesses. Do
not route the antenna wire next to any
harnesses.
. Adjust the antenna standing wave ratio as
recommended by the manufacturer.
. Connect the ground wire from the radio
chassis to the body.
. For details, consult a RENAULT dealer.
WARNING:
.Use a phone after stopping your vehicle in a
safe location. If you have to use a phone
while driving, exercise extreme caution at all
times so full attention may be given to
vehicle operation.
. If a conversation in a moving vehicle re-
quires you to take notes, pull off the road to
a safe location and stop your vehicle before
doing so.
CAUTION:
To avoid draining the vehicle battery, use a
phone after starting the engine.
For mo\fel with navigation s\bstem, see the separatel\b
provi\fe\f Navigation Owner’s Manual.
Your vehicle is equippe\f with the Bluetooth
ŠHan\fs-
Free Phone S\bstem. If \bou are an owner of a
Bluetooth
Šenable\f cellular phone, \bou can set up
the wireless connection between \bour cellular phone
an\f the in-vehicle phone mo\fule. With Bluetooth
Š
wireless technolog\b, \bou can make or receive a han\fs-
free telephone call with \bour cellular phone in the
vehicle.
Once \bour cellular phone is paire\f to the in-vehicle
phone mo\fule, no other phone connecting proce\fure
is require\f. Your phone is automaticall\b connecte\f with
the in-vehicle phone mo\fule when the ignition switch
is place\f in the “ON” position with the paire\f cellular
phone turne\f on an\f carrie\f in the vehicle.
You can register up to 5 \fifferent Bluetooth
Šcellular
phones to the in-vehicle phone mo\fule. However, \bou
can talk on onl\b one cellular phone at a time.
Before using the Bluetooth
ŠHan\fs-Free Phone S\bstem, refer to the following notes.
.
Set up the wireless connection between a cellular
phone an\f the in-vehicle phone mo\fule before
using the s\bstem.
. Some Bluetooth
Šenable\f cellular phones ma\b not
be recognize\f b\b the in-vehicle phone mo\fule.
. You will not be able to use a han\fs-free phone
un\fer the following con\fitions.
— Your vehicle is outsi\fe of the telephone service
area.
— Your vehicle is in an area where it is \fifficult to receive ra\fio waves; such as in a tunnel, in an
un\fergroun\f parking garage, near a tall buil\f-
ing or in a mountainous area.
— Your cellular phone is locke\f to prevent it from being \fiale\f.
When the ra\fio wave con\fition is not i\feal or ambient
soun\f is too lou\f, it ma\b be \fifficult for the other part\b
to hear \bour voice \furing a call. Please close the
win\fows if possible.
Do not place the cellular phone in an area surroun\fe\f
b\b metal or far awa\b from the in-vehicle phone mo\fule
to prevent tone qualit\b \fegra\fation an\f wireless
connection \fisruption.
While a cellular phone is connecte\f through the
Bluetooth
Šwireless connection, the batter\b power of
the cellular phone ma\b \fischarge quicker than usual.
The Bluetooth
ŠHan\fs-Free Phone S\bstem cannot
charge cellular phones.
Refer to the cellular phone Owner’s Manual regar\fing
the telephone charges, cellular phone antenna an\f
bo\f\b, etc.
This wireless han\fs-free s\bstem is base\f on Blue-
tooth
Štechnolog\b.
CAR PHONE OR CB RADIO Bluetooth
ŠHANDS-FREE PHONE
SYSTEM (if equipped for model
without navigation system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.Frequency: 2402 MHz - 2480 MHz
. Out\fut Power: 4\b14 dBm EIRP
. Modulation: FHSS GFSK 8DPSK, \f/4DQPSK
. Number of Channel: 79
. This wireless equi\fment cannot be used for any
services related to safety due to the \fossibility of
radio interference
REGULATORY INFORMATION
BluetoothŠis a trademark owned
by Bluetooth SIG, Inc\b and li-
censed to Clarion Co\b, Ltd\b and
Daewoo IS Cor\f\b
CE STATEMENT
Hereby “Yangfeng Visteon Automotive Electronics Co\b,
Ltd\b” and “Clarion Cor\foration” declares that this
Bluetooth car kit AV System is in com\fliance with the
essential requirements and other relevant \frovisions of
Directive 1999/5/EC\b
HANDS-FREE TELEPHONE OPERATION
(Ty\fe A)
JVH0006XFor Europe
JVH0046XFor South Africa1\b PHONE SEND button
2\b PHONE END/BACK button
3\b PHONE BOOK button
The following o\ftions can be selected:
. Paired list
. Pair \fhone
. Delete \fhone
. Bluetooth
Šconnection .
Delete \fhone book
. My number
Pairing \frocedure
If you wish to make a BluetoothŠconnection for the
first time between your mobile \fhone and the Blue-
tooth
Šsystem of the audio unit, \ferform the following
\fairing \frocedure\b
1\b Place the ignition switch in the “ACC” \fosition\b
2\b Switch on the audio system and your mobile \fhone\b
For the vehicle:
1\b Briefly \fush the MENU button\b
2\b Push the ENTER button\b
3\b Turn the MENU/VOL dial and select PAIR PHONE then \fush the ENTER button\b
4\b The dis\flay shows READY TO PAIR then PASS- CODE=1234\b
On the mobile \fhone:
1\b Activate the Bluetooth
Šconnection\b
2\b Activate the search mode for BluetoothŠequi\f-
ment\b Refer to the owner’s manual of your mobile
\fhone for further details\b If the search mode finds
the device, it will be shown on your mobile \fhone
dis\flay\b
3\b Select the device name MY CAR\b
4\b Enter the \fasscode number 1234 as shown on the dis\flay of the audio unit with the key\fad on
your mobile \fhone and then \fush the confirmation
button on your mobile \fhone\b
Heater and air conditioner, and audio system4-57
&RQGLWLRQ