2012 RENAULT PULSE phone


> (GLW    0RGHO .$2(0B5HQDXOW @
4. Push the clock adjusting knob*1to adjust the
\finutes.
To advance the ti\fe, hold do\bn the knob
*1.
Wait at least 5 seconds for the second display “:”
to flash.
5. Push the clock adjusting knob
*1to reset the
second counter.
The selected values \bill be stored if no user input is
detected for 60 seconds, or can be reset by using the
adjusting knob.
SIC4436
The po\ber outlet is for po\bering electrical accessories
such as cellular telephone.
CAUTION:
. The outlet and plug may be hot during or
immediately after use.
. This power outlet is not designed for use
with a cigarette lighter unit.
. Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
. Use power outlets with the engine running
to avoid discharging the vehicle battery.
. Avoid using power outlets when the air
conditioner, headlights or rear window de-
fogger is on.
. Before inserting or disconnecting a plug, be
sure to turn off the power switch of electrical
accessory being used and the ignition
switch.
. Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may open. .
Do not allow water to contact the outlet.
. When not in use, be sure to close the cap.
Instruments and controls2-39
POWER OUTLETS (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
3-4Pre-driving checks and adjustments
erasing all memory in the Intelligent Key com\fonents
when registering new keys, \be sure to take all
Intelligent Keys that you have to the RENAULT dealer.
*: Immo\bilizer
CAUTION:
.Be sure to carry the Intelligent Key with you.
Do not leave the vehicle with the Intelligent
Key inside.
. Be sure to carry the Intelligent Key with you
when driving. The Intelligent Key is a preci-
sion device with a built-in transmitter. To
avoid damaging it, please note the follow-
ing.
— The Intelligent Key is water resistant;
however, wetting may damage the In-
telligent Key. If the Intelligent Key gets
wet, immediately wipe until it is com-
pletely dry.
— Do not bend, drop or strike it against another object.
— Do not place the Intelligent Key for an extended period in a place where tem-
peratures exceed 608C (1408F) .
— Do not change or modify the Intelligent Key.
— Do not use a magnet key holder.
— Do not place the Intelligent Key near equipment that produces a magnetic
field such as a TV, audio equipment
and personal computers or cellular
phones. — Do not allow the Intelligent Key to come
into contact with water or salt water,
and do not wash it in a washing
machine. This could affect the system
function.
. If an Intelligent Key is lost or stolen,
RENAULT recommends erasing the ID code
of that Intelligent Key. This will prevent the
Intelligent Key from unauthorized use to
unlock the vehicle. For information regard-
ing the erasing procedure, please contact a
RENAULT dealer.
Mechanical key
SPA2033
To remove the mechanical key, release the lock kno\b at
the \back of the Intelligent Key.
To install the mechanical key, firmly insert it into the
Intelligent Key until the lock kno\b returns to the lock
\fosition.
Use the mechanical key to lock or unlock the doors.
(See “Door locks” (P.3-4) .)
WARNING:
.Always look before opening any doors, to
avoid an accident with oncoming traffic.
. Never leave children or adults who would
normally require the support of others alone
in the vehicle. They could unknowingly
activate switches or controls and inadver-
tently become involved in a serious accident.
SUPER LOCK SYSTEM (if equi\f\fed)
WARNING:
For Super Lock System equipped models, failure
to follow the precautions below may lead to
hazardous situations. Make sure the Super Lock
System activation is always safely conducted.
.When the vehicle is occupied, never lock the
doors with the remote keyless entry system
or the Intelligent Key system. Doing so will
trap the occupants, since the Super Lock
System prevents the doors from being
opened from the inside of the vehicle.
. Only operate the remote controller or the
Intelligent Key lock button when there is a
clear view of the vehicle. This is to prevent
anybody from being trapped inside the
vehicle through the Supper Lock System
activation.
Locking the doors with the remote controller or the
Intelligent Key “LOCK” \button
or the request
switch will lock all doors and activate the Su\fer Lock
System.
This means that none of the doors can \be o\fened from
the inside in order to \frevent theft.
DOOR LOCKS
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
3-10Pre-driving checks and adjustments
CAUTION:
.Do not allow the Intelligent Key, which
contains electrical components, to come
into contact with water or salt water. This
could affect the system function.
. Do not drop the Intelligent Key.
. Do not strike the Intelligent Key sharply
against another object.
. Do not change or modify the Intelligent Key.
. Wetting may damage the Intelligent Key. If
the Intelligent Key gets wet, immediately
wipe until it is completely dry.
. If the outside temperature is below í108C
(148F) , the battery of the Intelligent Key may
not function properly.
. Do not place the Intelligent Key for an
extended period in an area where tempera-
tures exceed 608C (1408F) .
. Do not attach the Intelligent Key with a key
holder that contains a magnet.
. Do not place the Intelligent Key near equip-
ment that produces a magnetic field, such as
a TV, audio equipment and personal compu-
ters or cellular phones.
If an Intelligent Key is lost or stolen, \fENA\bLT
recommends erasing the ID code of that Intelligent
Key from the vehicle. This may prevent the unauthor-
ized use of the Intelligent Key to operate the vehicle.
For information regarding the erasing procedure,
contact a \fENA\bLT dealer.
The Intelligent Key function can be disabled. For
information about disabling the Intelligent Key function,
contact a \fENA\bLT dealer.
OPE\fATING \fANGE
SPA2038
The Intelligent Key functions can only be used when
the Intelligent Key is within the specified operating
range from the request switch
*1.
When the Intelligent Key battery is discharged or
strong radio waves are present near the operating
location, the Intelligent Key system’s operating range
becomes narrower, and the Intelligent Key may not
function properly.
The operating range is within 80 cm (31.50 in) from
each request switch
*1.
If the Intelligent Key is too close to the door glass,
handle or rear bumper the request switches may not
function.
When the Intelligent Key is within the operating range,
it is possible for anyone, even someone who does not
carry the Intelligent Key, to push the request switch
and lock/unlock the doors.
\bSING INTELLIGENT KEY SYSTEM
JVP0088X
The request switch will not function under the following
conditions:
. When the Intelligent Key is left inside the vehicle
. When the Intelligent Key is not within the
operational range
. When any door is open or not closed securely
. When the Intelligent Key battery is discharged
. When the ignition switch is in the “ACC” or “ON”
position
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4 Heater and air conditioner, and audio system
Safety precautions ..................\V..................\V.....................\V..................\V........ 4-2
Venti\fators ..................\V..................\V..................\V..................\V..................\V........ 4-2Side venti\fators ..................\V..................\V..................\V............................\V 4-2
Center venti\fators ..................\V..................\V..................\V........................ 4-2
\beater and air conditioner (if equipped) ..................\V..................\V....... 4-3 Operating tips (for automatic air conditioner) ..................\V......... 4-4
Manua\f air conditioner ..................\V..................\V..................\V............... 4-4
Automatic air conditioner ..................\V..................\V..................\V.......... 4-6
Servicing air conditioner ..................\V..................\V..................\V........... 4-7
Audio system (if equipped) ..................\V..................\V...............................\V 4-8 Audio operation precautions ..................\V..................\V...................... 4-8
Antenna (if equipped) ..................\V..................\V.....................\V.......... 4-15
FM-AM radio with Compact Disc (CD) p\fayer (Type A) ..... 4-16
FM-AM radio with Compact Disc (CD) p\fayer (Type B) ..... 4-20
FM-AM radio with Compact Disc (CD) p\fayer (Type C) ..... 4-24
FM-AM radio with Compact Disc (CD) p\fayer (Type D) ..... 4-30 LW-MW-FM radio with compact disc (CD) p\fayer
(Type E) ..................\V..................\V...............................\V..................\V..... 4-35
LW-MW-FM radio with compact disc (CD) changer
(Type F) ..................\V..................\V...............................\V..................\V..... 4-40
FM-AM radio with Compact Disc (CD) p\fayer (Type G) .... 4-46
FM-AM radio with Compact Disc (CD) p\fayer and
navigation (if equipped) ..................\V..................\V..................\V....... 4-54
CD/USB memory (if equipped) care and c\feaning ............ 4-54
Steering whee\f switch for audio contro\f (if equipped) ..... 4-54
USB/AUX connector (if equipped) ..................\V..................\V............. 4-55
Car phone or CB radio ..................\V..................\V..................\V................ 4-56
B\fuetooth
Š\bands-Free Phone System (if equipped for mode\f
without navigation system) ..................\V..................\V............................ 4-56
Regu\fatory information ..................\V..................\V............................ 4-57
CE statement ..................\V..................\V.....................\V..................\V..... 4-57
\bands-free te\fephone operation (Type A) ..................\V.......... 4-57
\bands-free te\fephone operation (Type B) ..................\V.......... 4-63
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-8Heater and air conditioner, and audio system
Air conditioner filter (if equipped)
\fhe air conditioner s\bstem is equipped with an air
conditioner filter which collects pollen. \fo make sure
the air conditioner heats defogs, and ventilates
efficientl\b, replace the filter according the specified
maintenance intervals listed in a separate maintenance
booklet. \fo replace the filter, contact a RENAUL\f
dealer.
\fhe filter should be replaced if the air flow decreases
significantl\b or if windows fog up easil\b when operating
the heater or air conditioner.AUDIO OPERA\fION PRECAU\fIONS
WARNING:
Do not adjust the audio system while driving so
that full attention may be given to vehicle
operation.
\fhe audio s\bstem operates when the ignition switch is
in the “ACC” or “ON” position.
Radio
.Radio reception is affected b\b station signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
qualit\b normall\b are caused b\b these external
influences.
. Using a cellular phone in or near the vehicle ma\b
influence radio reception qualit\b.
Compact Disc (CD) pla\ber
.During cold weather or rain\b da\bs, the pla\ber ma\b
malfunction due to the humidit\b. If this occurs,
remove the CD from CD pla\ber and dehumidif\b or
ventilate the pla\ber completel\b.
. \fhe pla\ber ma\b skip while driving on rough roads.
. \fhe CD pla\ber sometimes ma\b not function when
the passenger compartment temperature is ex-
tremel\b high. Lower the temperature before use.
. Do not expose the CD to direct sunlight.
. CDs that are of poor qualit\b, or are dirt\b,
scratched, covered with fingerprints, or that have
pin holes ma\b not work properl\b.
. \fhe following CDs ma\b not work properl\b.
— Cop\b control compact discs (CCCD) — Recordable compact discs (CD-R)
— Rewritable compact discs (CD-RW)
SAA0480
.
Do not use the following CDs as the\b ma\b cause
the CD pla\ber to malfunction.
— 8 cm (3.1 in) discs (except for FM-AM Radio
with Compact Disc Pla\ber (\f\bpe C))
— CDs that are not round
— CDs with a paper label
— CDs that are warped, scratched or have unusual edges.
AUDIO SYSTEM (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.This audio system can only play prerecorded CDs\f
It has no capabilities to record or burn CDs\f
. If the CD cannot be played\b one of the following
messages will be displayed\f
Check disc:
— Confirm that the CD is inserted correctly (the
label side is facing up\b etc\f) \f
— Confirm that the CD is not bent or warped and it is free of scratches\f
Push eject:
This is a malfunction due to the temperature inside
the player is too high\f Remove the CD by pushing
the EJECT button\b and after a short time reinsert
the CD\f The CD can be played when the
temperature of the player returns to normal\f
Unplayable:
The file is unplayable in this audio system (only
MP3 or WMA CD) \f
USB (Universal Serial Bus) (if equipped)
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
. Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port. This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
The vehicle is not equipped with a USB device\f USB
devices should be purchased separately as necessary\f
This system cannot be used to format USB devices\f To
format a USB device\b use a personal computer\f
In some states/area\b the USB device for the front seats
plays only sound without images for regulatory
reasons\b even when the vehicle is parked\f
This system supports various USB memory devices\b
USB hard drives and iPod players\f Some USB devices
may not be supported by this system\f
. Partitioned USB devices may not be played
correctly\f
. Some characters used in other languages (Chi-
nese\b Japanese\b etc\f) are not displayed properly
on display\f Using English language characters
with a USB device is recommended\f
General notes for USB use:
Refer to your device manufacturer’s owner information
regarding the proper use and care of the device\f
Notes for iPod use:
iPod is a trademark of Apple Inc\f\b registered in the U\fS\f
and other countries\f
. Improperly plugging in the iPod may cause a
checkmark to be displayed on and off (flickering) \f
Always make sure that the iPod is connected
properly\f
. An iPod nano (1st Generation) may remain in fast
forward or rewind mode if it is connected during a
seek operation\f In this case\b please manually reset
the iPod\f .
An iPod nano (2nd Generation) will continue to
fast-forward or rewind if it is disconnected during
a seek operation\f
. An incorrect song title may appear when the Play
Mode is changed while using an iPod nano (2nd
Generation)
. Audiobooks may not play in the same order as
they appear on an iPod\f
. Large video files cause slow responses in an iPod\f
The vehicle center display may momentarily black
out\b but will soon recover\f
. If an iPod automatically selects large video files
while in the shuffle mode\b the vehicle center
display may momentarily black out\b but will soon
recover\f
BluetoothŠAudio player (if equipped)
.Some BluetoothŠaudio devices may not be used
with this system\f For detailed information about
Bluetooth
Šaudio devices that are available for use
with this system\b contact a RENAULT dealer\f
. Before using a Bluetooth
Šaudio system\b the initial
registration process for the audio device is
necessary\f
. Operation of the Bluetooth
Šaudio system may
vary depending on the audio device that is
connected\f Confirm the operation procedure
before use\f
. The playback of Bluetooth
Šaudio will be paused
under the following conditions\f The playback will
be resumed after the following conditions are
completed\f
— while using a Hands-free phone
— while checking a connection with a cellular phone
Heater and air conditioner, and audio system4-9
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-24Heater and air conditioner, and audio system
Push thebutton to select a desired memor\f.
MUTE button:
Press the
button to mute the sound. Press again
to restore the sound.
F\b-A\b RADIO WITH CO\bPACT DISC (CD) PLAYER (T\fpe C)
JVH0003X
1. Sound preference button
2. TA (Traffic Announcement)/NEWS button
3. F\b·A\b band select button
4. CD button
5. AUX button
6. CD EJECT button
7. \bENU button
8. SEEK/TRACK button 9. TUNE button
10. ENTER button
11. PHONE END/BACK button
12. POWER ON/OFF button/VOLU\bE control
knob
13. AUX IN (auxiliar\f input) jack
14. PHONE SEND button
15. PHONE BOOK button
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\fhis unit can only be activated when the ignition switch
for Anti-\fheft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
\fhe audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
\fo turn on the audio system, push the POWER ON\b
OFF button.
.\fhe system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
\fo turn off the audio system, push the POWER ON\b
OFF button.
Volume control:
\fo control the volume, turn the VOLUME control dial.
\furn the VOLUME control dial clockwise to make the
sound louder.
\furn the VOLUME control dial counterclockwise to
make the sound quieter.
Sound preference button:
\fo enter the audio mode (radio or CD) , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode. \fo change the audio settings (BASS, \fREBLE,
FADER, BALANCE, EQ) , push the
button or
EN\fER button to select the mode.
BASS ?\fREBLE ?BALANCE ?FADER ?EQ ?
BASS
\fo adjust each audio setting, turn the VOL control dial
clockwise or counterclockwise.
BASS: (í) to decrease \b (+) to increase
\fREB(LE): (í) to decrease \b (+) to increase
BAL(ANCE): (R) to right balance \b (L) to left balance
FADE(R): (F) to front fade \b (R) to rear fade
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
\furn the MENU\bVOL dial clockwise or counterclock-
wise. \fhe mode will change as follows:
OFF ⇔ENHANCE
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio settings mode will
automatically return to the normal mode.
MENU button:
\fo configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
PHONE SE\fUP ⇔SPEED VOL⇔CLOCK ⇔
BEEP ⇔PHONE SE\fUP
. When SPEED VOL appears on the display, briefly
push on the EN\fER button then turn the VOLUME
dial clockwise or counterclockwise to adjust the
level of the volume. Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed
volume setting results in the audio volume
increasing more rapidly with vehicle speed. Push
the EN\fER button again to save the setting.
. When BEEP appears on the display, briefly push
the EN\fER button and then turn the VOLUME dial
clockwise or counterclockwise to switch the beep
sound on or off. Push the EN\fER button again to
save the setting.
\fo configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5 seconds.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. \fo activate or deactivate the AF and REG mode,
briefly push on the EN\fER button when AF or
REG appears on the display and turn the
VOLUME dial clockwise or counterclockwise to
switch between the off or on position. After
selection, push the EN\fER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit will maintain and hold the station which is
broadcasting local (regional) programmes.
. \fo change the display language, briefly push the
EN\fER button when LANGUAGE appears on the
display then turn the VOLUME dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
Heater and air conditioner, and audio system4-25
&RQGLWLRQ