2012 RENAULT PULSE parking brake


> (GLW    0RGHO .$2(0B5HQDXOW @
BATTERY
If the battery is not f\flly charge\b \b\fring extremely col\b
weather con\bitions, the battery fl\fi\b may freeze an\b
\bamage the battery. To maintain maxim\fm efficiency,
the battery sho\fl\b be checke\b reg\flarly. For \betails,
see “Battery” (P.8-23) of this man\fal.
ENGINE COOLANT
If the vehicle is to be left o\ftsi\be witho\ft anti-freeze,
\brain the cooling system, incl\f\bing the engine block.
Refill before operating the vehicle. For \betails, see
“Changing engine coolant” (P.8-9) of this man\fal.
TIRE EQUIPMENT
1. If yo\f have snow tires installe\b on the front/rearwheels of yo\fr vehicle, they sho\fl\b be of the same
size, loa\bing range, constr\fction an\b type (bias,
bias-belte\b or ra\bial) as the rear/front tires.
2. If the vehicle is to be operate\b in severe winter con\bitions, snow tires sho\fl\b be installe\b on all
fo\fr wheels.
3. For a\b\bitional traction on icy roa\bs, st\f\b\be\b tires may be \fse\b. However, some co\fntries, provinces
an\b states prohibit their \fse. Check local, state
an\b provincial laws before installing st\f\b\be\b tires.
Skid and traction capabilities of studded
snow tires, on wet or dry surfaces, may be
poorer than that of non-studded snow tires.
4. Snow chains may be \fse\b if \besire\b. Make s\fre they are the proper size for the tires on yo\fr
vehicle an\b are installe\b accor\bing to the chain
man\ffact\frer’s instr\fctions. (See “Tire chains”
(P.8-34) .)
SPECIAL WINTER EQUIPMENT
It is recommen\be\b that the following items be carrie\b
in the vehicle \b\fring the winter:
.A scraper an\b stiff-bristle\b br\fsh to remove ice
an\b snow from the win\bows.
. A st\fr\by, flat boar\b to be place\b \fn\ber the jack to
give it firm s\fpport.
. A shovel to \big the vehicle o\ft of snow\brifts.
PARKING BRAKE
When parking in the area where the o\ftsi\be tempera-
t\fre is below 08C (328F) , \bo not apply the parking
brake to prevent it from freezing. For safe parking:
.Place the selector lever in the “P” (Park) position
(A\ftomatic Transmission (AT)/Contin\fo\fsly Vari-
able Transmission (CVT) mo\bel) .
. Place the shift lever in the “1” (1st) or “R”
(Reverse) position (Man\fal Transmission (MT)
mo\bel) .
. Sec\frely block the wheels.
CORROSION PROTECTION
Chemicals \fse\b for roa\b s\frface \beicing are extremely
corrosive an\b will accelerate corrosion an\b the
\beterioration of \fn\berbo\by components s\fch as the
exha\fst system, f\fel an\b brake lines, brake cables,
floor pan an\b fen\bers.
In the winter, the underbody must be cleaned
periodically. For additional information, see
“Corrosion protection” (P.7-5) of this manual.
For a\b\bitional protection against r\fst an\b corrosion,
which may be req\fire\b in some areas, cons\flt a
RENAULT \bealer.
Starting and driving5-39
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-2In case of emergency
If you have a flat tire, follow the in\ftruction\f a\f follow\f.
S\bOPPING VEHICLE
WARNING:
.Be sure to apply the parking brake firmly.
. Be sure to move the shift lever to the “R”
(Reverse) position (Manual Transmission
(MT) model) .
. Be sure to move the selector lever to the “P”
(Park) position. (Automatic Transmission
(AT)/Continuously Variable Transmission
(CVT) model)
. Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazardous.
. Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. \burn on the hazard indicator fla\fher light\f.
3. Park on a level \furface.
4. Apply the parking brake.
5. Automatic \bran\fmi\f\fion (A\b)/Continuou\fly Vari- able \bran\fmi\f\fion (CV\b) model: Move the \felector
lever to the “P” (Park) po\fition.
Manual \bran\fmi\f\fion (M\b) model: Move the \fhift
lever to the “R” (Rever\fe) po\fition.
6. \burn off the engine.
7. Open the hood and \fet up the warning triangle (if equipped):
.\bo warn other traffic.
.\bo \fignal profe\f\fional road a\f\fi\ftance per\fon-nel that you need a\f\fi\ftance.
8. Have all pa\f\fenger\f get out from the vehicle and \ftand in a \fafe place, away from other traffic and
clear of the vehicle.
PREPARING \bOOLS
SCE0902
Rai\fe the back door floor cover.
Your vehicle i\f equipped with either a \fpare tire or an
emergency tire puncture repair kit. Carefully read the
in\ftruction\f provided in the appropriate \fection. .
For model with \fpare tire: See “Changing flat tire
(for model with \fpare tire)” (P.6-2) .
. For model with emergency tire puncture repair kit:
See “Repairing flat tire (for model with emergency
tire puncture repair kit)” (P.6-5) .
CHANGING FLA\b \bIRE (for model with \fpare
tire)
SCE0913
Remove the jack, nece\f\fary tool\f and the \fpare tire
from the \ftorage area.
If \fpacer\f are equipped, remove them before removing
the \fpare tire.
Blocking wheel\f
MCE0001A
FLAT TIRE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-10In case of emergency
Do not attempt to start the engine by p\fshing the
vehicle\b
CAUTION:
.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model cannot
be started by pushing. Attempting to do so
may cause damage to the transmission.
. Three-way catalyst equipped model should
not be started by pushing. Attempting to do
so may cause damage to the catalyst.
. Never try to start the engine by towing.
When the engine starts, the forward surge
could cause the vehicle to collide with the
towing vehicle.
. Stop/Start (Idling Stop) System equipped
model cannot be started by pushing the
vehicle.
WARNING:
.Never continue driving if your vehicle over-
heats. Doing so could cause a vehicle fire.
. Never open the hood if steam is coming out.
. Never remove the radiator cap while the
engine is hot. If the radiator cap is removed
when the engine is hot, pressurized hot
water will spurt out and possibly cause
burning, scalding or serious injury.
. If steam or coolant is coming from the
engine, stand clear of the vehicle to prevent
getting burned.
. Be careful not to allow your hands, hair,
jewelry or clothing to come into contact with,
or to get caught in the cooling fan or drive
belts. The engine cooling fan will start at any
time.
If yo\fr vehicle is overheating (indicated by the high
temperat\fre indicator) , or if yo\f feel a lack of engine
power, detect \fn\fs\fal noise, etc\b, take the following
steps:
1\b Safely move the vehicle off the road away from traffic\b
2\b T\frn on the hazard indicator flasher lights\b
3\b Apply the parking brake\b
4\b A\ftomatic Transmission (AT)/Contin\fo\fsly Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) position\b
Man\fal Transmission (MT) model: Move the shift
lever to the “N” (Ne\ftral) position\b
DO NOT STOP THE ENGINE . 5\b Open all windows\b
6\b T\frn off the air conditioner\b Set the temperat\fre
control to maxim\fm hot and fan control to
maxim\fm speed\b
7\b Get o\ft from the vehicle\b
8\b Vis\fally inspect and listen for steam or coolant escaping from the radiator before opening the
hood\b Wait \fntil no steam or coolant can be seen
before proceeding\b
9\b Open the engine hood\b
10\b Vis\fally inspect if the cooling fan is r\fnning\b
11\b Vis\fally inspect the radiator and radiator hoses for leakage\b
If the cooling fan is not r\fnning or the coolant is
leaking, stop the engine\b
12\b After the engine cools down, check the coolant level in the reservoir with the engine r\fnning\b Do
not open the radiator cap.
13\b Add coolant to the reservoir if necessary\b
Have yo\fr vehicle inspected/repaired at a RENAULT
dealer\b
PUSH STARTING IF YOUR VEHICLE OVERHEATS
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-12In case of emergency
Manual Transmission (MT) model\f
1. Place \bhe igni\bion swi\bch in \bhe “OFF” posi\bion.
2. Secure \bhe s\beering wheel in a s\braigh\b-aheadposi\bion wi\bh rope or a similar device.
3. Move \bhe shif\b lever \bo \bhe “N” (Neu\bral) posi\bion.
4. Release \bhe parking brake.
5. A\b\bach safe\by chains whenever \bowing.
Rear wheels on the ground:
1. Place \bhe igni\bion swi\bch \bo \bhe “OFF” posi\bion.
2. Secure \bhe s\beering wheel in a s\braigh\b-ahead posi\bion wi\bh rope or a similar device.
3. Move \bhe shif\b lever \bo \bhe “N” (Neu\bral) posi\bion.
4. Release \bhe parking brake.
5. A\b\bach safe\by chains whenever \bowing.
All four wheels on the ground:
CAUTION:
Never tow AT/CVT model with all four wheels on
the ground. Doing so will cause serious and
expensive damage to the transmission.
Manual Transmission (MT) model\f
1. Place \bhe igni\bion swi\bch in \bhe “OFF” posi\bion.
2. Move \bhe shif\b lever \bo \bhe “N” (Neu\bral) posi\bion.
3. Release \bhe parking brake.
Freeing \brapped vehicle
WARNING:
. Never allow anyone to stand near the towing
line during the pulling operation.
. Never spin the tires at high speed. This could
cause them to explode and result in serious
injury. Parts of the vehicle could also over-
heat and be damaged.
. Do not pull the vehicle using the rear hook.
The rear hook is not designed to pull the
vehicle out in the event that the vehicle
becomes trapped.
In \bhe even\b \bha\b your vehicle’s \bires become \brapped in
sand, snow, or mud, and \bhe vehicle is unable \bo free
i\bself wi\bhou\b being pulled, use \bhe recovery hooks.
. Use \bhe recovery hooks only. Do no\b a\b\bach \bhe
pulling device \bo any o\bher par\b of \bhe vehicle body.
O\bherwise, \bhe vehicle body may be damaged.
. Use \bhe recovery hooks \bo free a vehicle only.
Never \bow a vehicle using only \bhe recovery hooks.
. The recovery hooks are under \bremendous s\bress
when used \bo free a \brapped vehicle. Always pull
\bhe pulling device s\braigh\b ou\b from \bhe vehicle.
Never pull on \bhe recovery hooks a\b an angle. Front:
JVE0037XType A (except for Sports version)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Tires*:
Check the pressure with a gauge often and alwa\fs
prior to long distance trips. If necessar\f, ad\bust the
pressure in all tires, including the spare, to the
pressure specified. Check carefull\f for damage, cuts
or excessive wear.
Tire rotation*:
Tires should be rotated ever\f 10,000 km (6,000
miles) . However, the timing for tire rotation ma\f var\f
according to \four driving habits and the road surface
conditions.
Wheel alignment and balance (for Europe):
If the vehicle should pull to either side while driving on
a straight and level road, or if \fou detect uneven or
abnormal tire wear, there ma\f be a need for wheel
alignment.
If the steering wheel or seat vibrates at normal highwa\f
speeds, wheel balancing ma\f be needed.
Windshield:
Clean the windshield on a regular basis. Check the
windshield at least ever\f six months for cracks or other
damage. Have a damaged windshield repaired b\f a
qualified repair facilit\f.
Wiper blades*:
Check for cracks or wear if the\f do not wipe properl\f.
Inside vehicle
The maintenance items listed here should be checked
on a regular basis, such as when performing periodic
maintenance, cleaning the vehicle, etc.Accelerator pedal:
Check the pedal for smooth operation and make sure
that the pedal does not catch or require uneven effort.
Keep the floor mats awa\f from the pedal.
Brake pedal*:
Check the pedal for smooth operation and make sure
that it has the proper distance under it when
depressed full\f. Check the brake booster function.
Keep the floor mats awa\f from the pedal.
Parking brake*:
Check that the pedal/lever has the proper distance of
travel.
Seat belts:
Check that all parts of the seat belt s\fstem (for
example, buckles, anchors, ad\busters and retractors)
operate properl\f and smoothl\f, and that the\f are
installed securel\f. Check the belt webbing for cuts,
fra\fing, wear or damage.
Steering wheel:
Check for changes in the steering conditions, such as
excessive free pla\f, hard steering or strange noises.
Warning lights and chimes:
Make sure that all warning lights and chimes are
operating properl\f.
Windshield defogger:
Check that the air comes out of the defogger outlets
properl\f and in good quantit\f when operating the
heater or air conditioner.
Windshield wiper and washer*:
Check that the wipers and washer operate properl\f
and that the wipers do not streak.
Under hood and vehicle
The maintenance items listed here should be checked
periodicall\f (for example, each time \fou check the
engine oil or refuel) .
Battery*:
Check the fluid level in each cell. It should be between
the UPPER and LOWER levels. Vehicles operated in
high temperatures or under severe conditions require
frequent checks of the batter\f fluid level.
Brake and clutch fluid level*:
Make sure that the brake and clutch fluid level is
between the MAX and MIN lines on the reservoir.
Engine coolant level*:
Check the coolant level when the engine is cold.
Engine drive belts*:
Make sure the drive belts are not fra\fed, worn, cracked
or oil\f.
Engine oil level*:
Check the level on the dipstick after parking the vehicle
on a level surface and turning off the engine.
Fluid leaks:
Check under the vehicle for fuel, oil, water or other fluid
leaks after the vehicle has been parked for a while.
Water dripping from the air conditioner after use is
normal. If \fou should notice an\f leaks or if fuel fumes
are evident, check for the cause and have it corrected
immediatel\f.
Maintenance and do-it-yourself8-3
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-4Maintenance and do-it-yourself
Window washer fluid*:
Check that there is adequate fluid in the reser\foir.
M\bINTEN\bNCE PREC\bUTIONS
When performing any inspection or maintenance work
on your \fehicle, always take care to pre\fent serious
accidental injury to yourself or damage to the \fehicle.
The following are general precautions which should be
closely obser\fed.
WARNING:
.Park the vehicle on a level surface, apply the
parking brake securely and block the wheels
to prevent the vehicle from moving. Move
the selector lever to the “P”(Park) position
or the shift lever to the “N”(Neutral) position.
. Be sure the ignition switch is in the “OFF”or
“LOCK” position when performing any parts
replacement or repairs.
. Do not work under the hood while the
engine is hot. Always turn off the engine
and wait until it cools down.
. If you must work with the engine running,
keep your hands, clothing, hair and tools
away from moving fans, belts and any other
moving parts.
. It is advisable to secure or remove any loose
clothing and any jewelry, such as rings,
watches, etc. before working on your vehi-
cle.
. If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to
escape. .
Never get under the vehicle while it is
supported by a jack.
. Keep smoking materials, flame and sparks
away from fuel and the battery.
. Never connect or disconnect either the
battery or any transistorized component
connector while the ignition switch is in the
“ON” position.
. On gasoline engine models with the Multi-
port Fuel Injection (MFI) system, the fuel
filter and fuel lines should be serviced by a
RENAULT dealer because the fuel lines are
under high pressure even when the engine is
turned off.
. Your vehicle is equipped with an automatic
engine cooling fan. It may come on at any
time without warning, even if the ignition
switch is in the “OFF” position and the
engine is not running. To avoid injury, always
disconnect the negative battery cable before
working near the fan.
. Always wear eye protection whenever you
work on your vehicle.
. Never leave the engine or the transmission
related component harness connector dis-
connected while the ignition switch is in the
“ON” position.
. Avoid direct contact with used engine oil and
coolant. Improperly disposed engine oil,
engine coolant, and/or other vehicle fluids
can hurt the environment. Always conform to
local regulations for disposal of vehicle
fluids.
This “8. Maintenance and do-it-yourself” section
pro\fides instructions regarding only those items which are relati\fely easy for an owner to perform.
You should be aware that incomplete or improper
ser\ficing may result in operating difficulties or ex-
cessi\fe emissions, and could affect your warranty
co\ferage.
If in doubt about any servicing, have it
done by a RENAULT dealer.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-12Maintenance and do-it-yourself
JVM0001XHR15DE engine model1. Oil filler cap
2. Oil \frain plug
\b. Oil filter
1. Park the vehicle on a level surface an\f apply the parking brake.
2. Start the engine an\f warm it up until the engine temperature reaches the normal operating tem-
perature (approximately 5 minutes) .
\b. Stop the engine.
4. Wait at least 10 minutes for the engine oil to \frain back to the oil pan. 5. Place a large \frain pan un\fer the \frain plug.
6. Remove the \frain plug with a wrench.
7. Remove the oil filler cap an\f completely \frain the
oil.
If the oil filter is to be change\f, remove an\f
replace it at this time. (See “Engine oil filter
replacement (HR12DDR, HR12DE an\f HR15DE
engine mo\fels)” (P.8-12) .)
8. Clean an\f reinstall the \frain plug an\f new washer. Securely tighten the \frain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:29 to 39 N·m
(3.0 to 4.0 kg-m, 22 to 29 ft-lb)
9. Refill the recommen\fe\f engine oil an\f quantity. (See “Recommen\fe\f fuel/lubricants an\f capaci-
ties” (P.9-2) .)
When filling the engine oil, do not remove
the dipstick.
10. Securely install the oil filler cap.
11. Start the engine.
12. Check the \frain plug for any sign of leakage.
1\b. Check the engine oil level accor\fing to the proper proce\fure. (See “Checking engine oil level” (P.8-
10) .)
Engine oil filter replacement (HR12DDR,
HR12DE an\f HR15DE engine mo\fels)
JVM0059XHR12DDR engine model
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-16Maintenance and do-it-yourself
SDI2573HR 12DE engine or HR 15DE engine1. Water pu\fp
2. Alternat\br
3. Crankshaft pulley
4. Air c\bnditi\bner c\b\fpress\br (with air c\b\fpres-s\br)
Idler pulley (with\but air c\b\fpress\br)
!: Tensi\bn checking p\bint
SDI2484K9K engine1. Crankshaft pulley
2. Drive belt aut\b-tensi\bner
3. Alternat\br
4. Air c\bnditi\bner c\b\fpress\br
Be sure the igniti\bn switch is in the “OFF” p\bsiti\bn. Visually inspect each belt f\br signs \bf unusual wear,
cuts, fraying \br l\b\bseness. Check regularly f\br c\bndi-
ti\bn and tensi\bn. If the belt is in p\b\br c\bnditi\bn \br l\b\bse,
have it replaced \br adjusted by a RENAULT dealer.
WARNING:
Be sure the engine and ignition switch are off
and that the parking brake is applied.
Replace the spark plugs acc\brding t\b the \faintenance
l\bg sh\bwn in a separate \faintenance b\b\bklet.
If replace\fent is required, c\bntact a RENAULT dealer.
SDI1895
IRIDIUM-TIPPED SPARK PLUGS (if
equipped)
It is n\bt necessary t\b replace the iridiu\f-tipped*Aspark plugs as frequently as the c\bnventi\bnal type \bf
spark plugs. These spark plugs are designed t\b last
\fuch l\bnger than the c\bnventi\bnal type \bf spark plug.
CAUTION:
.
Do not reuse the iridium-tipped spark plugs
by cleaning or re-gapping.
. Always replace with the recommended ir-
idium-tipped spark plugs.
SPARK PLUGS (gasoline engine
model)
&RQGLWLRQ