2012 RENAULT PULSE instrument panel


> (GLW    0RGHO .$2(0B5HQDXOW @
B) using the Stop/Start System are kept in a su\fmenu.
Trip Saving \bType A)
The Trip Saving mode shows the estimated CO2
exhaust emissions prevented since last reset.
It is possi\fle to reset using the [RESET] su\fmenu then
push the
switch*Ato set to zero.
NOTE:
The [Trip Saving] value is the same information
that is displayed when the engine is automati-
cally stopped by the Stop/Start System.
Total Saving \bType B)
The Total Saving mode shows:
. The estimated CO2 exhaust emissions prevented.
. The time that the engine has \feen stopped \fy the
Stop/Start System.
NOTE:
The [Total Saving] values cannot be reset and
show accumulated Stop/Start System informa-
tion since the vehicle was built.
HEADLIGHT SWITCH
SIC3782Type A
SIC3783Type BRENAULT recommends that you consult the local
regulations concerning the use of lights.
AUTO position \bif equipped)
When the ignition switch is in the “ON” position and
the headlight switch is in the “AUTO” position, the
headlights, front clearance lights, instrument panel
lights, rear com\fination light, and other lights turn on
automatically depending on the \frightness of the
surroundings.
The headlights will turn on automatically at twilight or in rainy weather \bwhen the windshield wiper is operated
continuously) \bfor Hong Kong) .
When the ignition switch is turned to the “OFF”
position, the lights will turn off automatically.
JVI0023X
CAUTION:
Do not place any objects on top of the sensor*A. The sensor senses the brightness level and
controls the autolight function. If the sensor is
covered, it reacts as if it is dark, and the
headlights will illuminate.
position
Theposition turns on the front clearance lights,
instrument panel lights, rear com\fination lights and
other lights.
Instruments and controls2-29
HEADLIGHT AND TURN SIGNAL
SWITCH
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
2-32Instruments and controls
FRONT FOG LIGHTS
SIC3811Type A
SIC3813Type BTo tu\fn on the \b\font \bog lights, tu\fn the \bog light switch
to theposition with the headlight switch in theo\fposition.
To tu\fn o\b\b the \bog lights, tu\fn the \bog light switch to the
“OFF” position.
When the headlight switch is in the “AUTO” position (i\b
equipped):
. Tu\fning the \bog light switch to the
position
will tu\fn on the headlights, \bog lights and the othe\f
lights while the ignition switch is in the “ON” position o\f the engine is \funning.
REAR FOG LIGHT
SIC3812Type A
SIC4066Type B
SIC3814Type CTo tu\fn on the \fea\f \bog light, tu\fn the \bog light switch to
theo\fposition. The switch \fetu\fns to theposition automatically, and the \fea\f \bog light will
illuminate with the \b\font \bog lights. Make su\fe the
indicato\f light on the inst\fument panel illuminates.
To tu\fn o\b\b the \fea\f \bog light, tu\fn the \bog light switch to
the
position again. Make su\fe theindicato\f
light on the inst\fument panel tu\fns o\b\b.
To tu\fn o\b\b both the \b\font and \fea\f \bog lights, tu\fn the
\bog light switch to the “OFF” position.
When the headlight switch is in the “AUTO” position (i\b
equipped):
. Tu\fning the \bog light switch to the
position
will tu\fn on the headlights, \bog lights and the othe\f
lights while the ignition switch is in the “ON”
position o\f the engine is \funning.
The \fea\f \bog light should be used only when visibility is
se\fiously \feduced. [Gene\fally, to less than 100 m (328
\bt)]
FOG LIGHT SWITCH (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
SPA2407
.Do not push the door hand\fe request swit\bh with
the Inte\f\figent Key he\fd in your hand as i\f\fustrated.
The \b\fose distan\be to the door hand\fe wi\f\f \bause
the Inte\f\figent Key system to have diffi\bu\fty
re\bognizing that the Inte\f\figent Key is outside the
vehi\b\fe.
. After \fo\bking the doors using the door hand\fe
request swit\bh, make sure that the doors have
been se\bure\fy \fo\bked by operating the door
hand\fes.
. When \fo\bking the doors using the door hand\fe
request swit\bh, make sure to have the Inte\f\figent
Key in your possession before operating the door
hand\fe request swit\bh to prevent the Inte\f\figent
Key from being \feft in the vehi\b\fe.
. The door hand\fe request swit\bh is operationa\f on\fy
when the Inte\f\figent Key has been dete\bted by the
Inte\f\figent Key system.
. Do not pu\f\f the door hand\fe before pushing the
door hand\fe request swit\bh. The door wi\f\f be
un\fo\bked but wi\f\f not open. Re\fease the door
hand\fe on\be and pu\f\f it again to open the door.
Request swit\bh \fo\bations
JVP0095X
JVP0089X
When you \barry the Inte\f\figent Key with you, you \ban
\fo\bk or un\fo\bk a\f\f doors by pushing the door hand\fe
request swit\bh (driver’s or front passenger’s)
*Aor
ba\bk door request swit\bh*Bwithin the range of
operation.
When you \fo\bk or un\fo\bk the doors, the hazard
indi\bator wi\f\f f\fash as a \bonfirmation.
Lo\bking doors
1. Push the ignition swit\bh to the “OFF” position.
2. Carry the Inte\f\figent Key with you.
3. C\fose a\f\f doors.
4. Push the door hand\fe request swit\bh
*A(driver’s
or front passenger’s) or the ba\bk door request
swit\bh
*B.
5. A\f\f doors and the ba\bk door wi\f\f be \fo\bked.
6. The hazard indi\bator f\fashes on\be.
7. Operate door hand\fes to \bonfirm that the doors have been se\bure\fy \fo\bked.
Lockout protection:
To prevent the Inte\f\figent Key from being a\b\bidenta\f\fy
\fo\bked in the vehi\b\fe, \fo\bkout prote\btion is equipped
with the Inte\f\figent Key system.
. When the Inte\f\figent Key is \feft in the vehi\b\fe and
you try to \fo\bk the door using the driver’s inside
\fo\bk knob after getting out of the vehi\b\fe, a\f\f the
doors wi\f\f un\fo\bk automati\ba\f\fy and a \bhime wi\f\f
sound after the door is \b\fosed.
. When the Inte\f\figent Key is \feft in the vehi\b\fe whi\fe
the driver’s door is opened and you try to \fo\bk the
door using the power door \fo\bk swit\bh after
getting out of the vehi\b\fe, an inside warning \bhime
wi\f\f sound after the power door \fo\bk swit\bh or the
driver’s inside \fo\bk knob is operated.
CAUTION:
The lockout protection may not function under
the following conditions:
.When the Intelligent Key is placed on top of
the instrument panel.
Pre-driving checks and adjustments3-11
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-48Heater and air conditioner, and audio system
Scroll direction:
Set the scrolling behavior of the \fUNE\bMENU\bEN\fER
dial to scroll UP or DOWN.
Day/Night button:
Push the
button to switch the display brightness
between the daytime and nighttime modes.
AUX button:
\fhe AUX IN jack is located on the instrument panel. For
details, see “USB\bAUX connector” (P.4-55) . \fhe AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, digital audio player or laptop computer.
Push the
button to play a compatible device when
it is plugged into the AUX IN jack.
RENAUL\f strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
monaural cable is used.
CD player operation
JVH0509X
\fhe audio system operates when the ignition switch is in the “ACC” or “ON” position.
Loading:
Insert a CD into the slot with the label side facing up.
\fhe CD will be guided automatically into the slot and
will start playing. After loading the CD, the number of
tracks and the playtime will appear on the display.
CAUTION:
Do not force the CD into the slot. This could
damage the player.
NOTE:
.
The CD player accepts normal audio CDs or
CDs containing MP3/WMA files.
. The audio unit will automatically detect if a
CD containing MP3/WMA files is inserted,
and [MP3CD] will be indicated.
. An error notification message will be dis-
played when an incompatible disc (e.g. DVD)
is inserted, or if the player cannot read the
CD. Eject the disc and insert another disc.
List view:
While the track is being played, push either the \fUNE\b
MENU\bEN\fER dial or the
button to display the
available tracks in a listed view mode. \furn the \fUNE\b
MENU\bEN\fER dial to select a track from the list, or a
track to start listening to, and then push the \fUNE\b
MENU\bEN\fER dial.
Quick search:
In the list view mode, a quick search can be performed
to find a track from the list. Push the
button, turn
the \fUNE\bMENU\bEN\fER dial to the first alphabetic
letter of the song title and then push the \fUNE\bMENU\b
EN\fER dial. When found, a list of the available songs
will be displayed. Select, and push the \fUNE\bMENU\b EN\fER dial to play the preferred track.
CD button:
When the
button is pushed while the audio
system is turned off and a CD is loaded, the audio
system will turn on and a CD will start playing
automatically. If the radio or AUX source mode is
already playing, it will automatically turn off and the CD
will start playing.
However, if the CD is not loaded, then a notification
message will be displayed and the audio unit will
remain in the radio or AUX source mode.
Fast Forward/Rewind buttons:
Push and hold the
\bbutton to fast forward or
rewind through the track. When the button is released,
the track will play at normal playing speed.
\frack up\bdown:
By pushing the
\bbutton once, the track will
skip forward to the next track or backward to the
beginning of the current track. Push the
\bbutton more than once to skip through the tracks.
Folder browsing:
If the recorded media contains folders with music files,
pushing the
\bbutton will play the tracks of
each folder in sequence.
\fo select a preferred folder:
1. Push the \fUNE\bMENU\bEN\fER dial or the
button and a list of tracks in the current folder is
displayed.
2. Push the
button.
3. \furn the \fUNE\bMENU\bEN\fER dial to highlight the preferred folder.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
4-50Heater and air conditioner, and audio system
2. Push and hold a radio memor\f button*1-*6until a beep sounds. \bThe radio mutes when the
memor\f button is pushed.)
3. The channel indicator will displa\f and the radio mute disengages, indicating that the memor\f is
stored properl\f.
4. Perform steps 1 - 3 for all other memor\f buttons.
If the batter\f cable is disconnected, or if the audio fuse
blows, the radio memor\f will be erased. If this occurs,
reset the desired stations.
USB memor\f device operation
Audio main operation:
The USB connector is located on the instrument panel.
For details, see “USB/AUX connector” \bP.4-55) .
Open the lid and connect a USB memor\f device into
the connector. The s\fstem will switch to the USB
memor\f device mode automaticall\f.
If the s\fstem is turned off while the USB memor\f
device is pla\fing, pushing the
dial will start the
USB memor\f device.
If the USB memor\f device cannot be pla\fed, one of the
following messages will be displa\fed.
. “USB memor\f device not supported”
. “No audio file detected”
WARNING:
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION:
.Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is
connected correctly into the USB port.
(Some USB devices come with a
mark as a guide. Make sure that the mark
is facing the correct direction before insert-
ing the device.)
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to \four device manufacturer’s owner information
regarding the proper use and care of the device.
AUX button:
To operate the USB memor\f device use one of the
following methods:
. Push the
button then turn the TUNE/MENU/
ENTER dial to select the USB item. Once high-
lighted, push the TUNE/MENU/ENTER dial.
. Push the
button repeatedl\f until USB is
highlighted, and then push the TUNE/MENU/
ENTER dial.
Operation buttons:
The following operations are identical to the audio main
operation of the Compact Disc \bCD) operation. For
details, see “CD pla\fer operation” \bP.4-48) . .
List view
. Quick search
.
. MIX \bRandom pla\f)
. RPT \bRepeat track)
. Folder browsing
DISP button:
While a track with recorded music information tags
\bID3-tags) is being pla\fed, the title of the pla\fed track
is displa\fed. If the tags are not provided, a notification
message is displa\fed.
When the
button is pushed repeatedl\f, further
information about the track can be displa\fed along
with the track title as follows:
Track time ?Artist ?Album ?Folder name ?Track
time
Track details:
B\f pushing and holding the
button the displa\f will
show a detailed overview and after a few seconds it
will return to the main displa\f. Push the
button
briefl\f to return to the main displa\f immediatel\f.
iPod pla\fer operation
Connecting iPod:
The USB connector is located on the instrument panel.
For details, see “USB/AUX connector” \bP.4-55) . Open
the USB connector lid and connect the iPod cable to
the USB connector. The batter\f of the iPod is charged
while the device is connected to the vehicle.
Depending on the version of the iPod, the displa\f on
the iPod shows a RENAULT or Accessor\f Attached
screen when the connection is completed. When the
iPod is connected to the vehicle, the iPod music librar\f
can onl\f be operated b\f the vehicle audio controls.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
JVH0005XType B1. SOURCE select s\fitch
2. V\blume c\bntr\bl s\fitch
3. Tuning s\fitch
The audi\b system can be \bperated using the c\bntr\bls
\bn the steering \fheel.
SOURCE select s\fitch
Push the SOURCE select s\fitch t\b change the m\bde
t\b available audi\b s\burce.
V\blume c\bntr\bl s\fitch
Push up \br d\b\fn the v\blume c\bntr\bl s\fitch t\b increase
\br decrease the v\blume.
Tuning s\fitch
Memory change (radio):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
change the next \br previ\bus radi\b preset.
SEEK tuning (radio):
Push the tuning s\fitch f\br m\bre than 1.5 sec\bnds t\b
seek the next \br previ\bus radi\b stati\bn. APS (Automatic Program Search) FF, APS REW
(CD):
Push the tuning s\fitch f\br less than 1.5 sec\bnds t\b
return t\b the beginning \bf the present pr\bgram \br skip
t\b the next pr\bgram. Push several times t\b skip back \br
skip thr\bugh pr\bgrams.
This system searches f\br the blank intervals bet\feen
selecti\bns. If there is a blank interval \fithin \bne
pr\bgram \br there is n\b interval bet\feen pr\bgrams,
the system may n\bt st\bp in the desired \br expected
l\bcati\bn.
Type A:
JVH0007X
The USB/AUX c\bnnect\br is \bn the l\b\fer center \bf the
instrument panel.
F\br details, see the separately pr\bvided Navigati\bn
O\fner’s Manual.
Type B:
JVH0731X
The USB/AUX c\bnnect\br is l\bcated \bn the instrument
panel. F\br details, see “USB mem\bry device \bperati\bn”
(P.4-50) , “iP\bd player \bperati\bn” (P.4-50) \br “Audi\b
main \bperati\bn” (P.4-47) .
Heater and air conditioner, and audio system4-55
USB/AUX CONNECTOR (if
equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
.If the vehicle battery is discharged, the
ignition switch cannot be switched from
the “LOCK” position, and if the steering lock
is engaged, the steering wheel cannot be
moved. Charge the battery as soon as
possible. (See “Jump starting” (P.6-8) .)
Operating range
SSD0436
The Intelligent \fey can only \be used for starting the
engine when the Intelligent \fey is within the specified
operating range
*1.
When the Intelligent \fey \battery is almost discharged
or strong radio waves are present near the operating
location, the Intelligent \fey system’s operating range
\becomes narrower and may not function properly.
If the Intelligent \fey is within the operating range, it is
possi\ble for anyone, even someone who does not carry
the Intelligent \fey, to push the ignition switch to start
the engine.
. The luggage room area is not included in the
operating range, \but the Intelligent \fey may
function.
. If the Intelligent \fey is placed on the instrument
panel, inside the glove \box, door pocket or the
corner of the interior compartment, the Intelligent \fey may not function.
. If the Intelligent \fey is placed near the door or
window outside the vehicle, the Intelligent \fey
may function.
Automatic transmission (AT)/Continuously
Varia\ble Transmission (CVT) model
The ignition lock is designed so that the ignition switch
cannot \be switched to the “LOC\f” position until the
selector lever is moved to the “P” (Park) position.
When pushing the ignition switch to the “OFF”
position, make sure the selector lever is in the “P”
(Park) position.
Type A (model with dot matrix display):
When the ignition switch cannot \be switched to the
“LOC\f” position:
1. SHIFT “P” warning appears on the dot matrix
display (in the vehicle information display) and a
chime sounds.
2. Move the selector lever to the “P” (Park) position.
3. If the ignition switch is in the “ACC” position, the “PUSH” warning appears on the dot matrix
display.
4. Push the ignition switch. The ignition switch is switched to the “ON” position.
5. The “PUSH” warning appears again on the dot matrix display.
6. Push the ignition switch. The ignition switch is switched to the “OFF” position.
7. Open the door. The ignition switch will change to the “LOC\f” position.
For warnings and indicators on the Vehicle information
display, see “Vehicle information display” (P.2-20) . Type B (model without dot matrix display) :
1. Move the selector lever to the “P” (Park) position.
2. Push the ignition switch to the “OFF” position.
3. Open the door. The ignition switch will change to
the “LOC\f” position.
If the ignition switch is switched to the “LOC\f”
position, the selector lever cannot \be moved from the
“P” (Park) position. The selector lever can \be moved if
the ignition switch is in the “ON” position with the foot
\brake depressed.
STEERING LOC\f
The ignition switch is equipped with an anti-theft
steering lock device.
To lock steering wheel
1. Push the ignition switch to the “OFF” position where the ignition switch position indicator will not
illuminate.
2. Open or close the door. The ignition switch turns to the “LOC\f” position.
3. Turn the steering wheel 1/6 of a turn to the right or left from the straight up position.
To unlock steering wheel
Push the ignition switch, and the steering wheel will \be
automatically unlocked.
CAUTION:
.If the battery of the vehicle is discharged, the
push-button ignition switch cannot be
switched from the “LOCK” position.
. If the ignition switch position does not
change from the “LOCK” position, push the
ignition switch again while rotating the
Starting and driving5-7
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-22Starting and driving
.The driver ’s seat belt is unfastened, or
driver’s door is open (for MT model) .
. The hood is open.
The Stop/Start System is al\fays engaged at the start
o\b a journey (once the engine has been started) . The
engine is automatically stopped and restarted during
the journey i\b conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
Engine stop
JVS0071X
When the engine is stopped the in\bormation is
displayed \bor a \be\f seconds.
Vehicle information display: 1. Engine stop guidance
Instrument panel: 2. Stop/Start System indicator light
See “Vehicle in\bormation display” (P.2-20) about the
display. NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
JVS0073X
Whilst the engine remains stopped the vehicle
in\bormation display sho\fs the accumulated quantity
(estimate) o\b carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
1. CO2 saved in\bormation
Instrument panel: 2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be s\fitched bet\feen Stop/Start
System in\bormation and drive computer in\borma-
tion by a short press o\b the
button.
System \bault
JVS0074X
When automatic restart is not possible the in\bormation
is displayed. The engine must be started by turning or
pushing the ignition s\fitch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK \farning
JVS0081XType A
&RQGLWLRQ