2012 RENAULT PULSE lock


> (GLW    0RGHO .$2(0B5HQDXOW @
BATTERY
If the battery is not f\flly charge\b \b\fring extremely col\b
weather con\bitions, the battery fl\fi\b may freeze an\b
\bamage the battery. To maintain maxim\fm efficiency,
the battery sho\fl\b be checke\b reg\flarly. For \betails,
see “Battery” (P.8-23) of this man\fal.
ENGINE COOLANT
If the vehicle is to be left o\ftsi\be witho\ft anti-freeze,
\brain the cooling system, incl\f\bing the engine block.
Refill before operating the vehicle. For \betails, see
“Changing engine coolant” (P.8-9) of this man\fal.
TIRE EQUIPMENT
1. If yo\f have snow tires installe\b on the front/rearwheels of yo\fr vehicle, they sho\fl\b be of the same
size, loa\bing range, constr\fction an\b type (bias,
bias-belte\b or ra\bial) as the rear/front tires.
2. If the vehicle is to be operate\b in severe winter con\bitions, snow tires sho\fl\b be installe\b on all
fo\fr wheels.
3. For a\b\bitional traction on icy roa\bs, st\f\b\be\b tires may be \fse\b. However, some co\fntries, provinces
an\b states prohibit their \fse. Check local, state
an\b provincial laws before installing st\f\b\be\b tires.
Skid and traction capabilities of studded
snow tires, on wet or dry surfaces, may be
poorer than that of non-studded snow tires.
4. Snow chains may be \fse\b if \besire\b. Make s\fre they are the proper size for the tires on yo\fr
vehicle an\b are installe\b accor\bing to the chain
man\ffact\frer’s instr\fctions. (See “Tire chains”
(P.8-34) .)
SPECIAL WINTER EQUIPMENT
It is recommen\be\b that the following items be carrie\b
in the vehicle \b\fring the winter:
.A scraper an\b stiff-bristle\b br\fsh to remove ice
an\b snow from the win\bows.
. A st\fr\by, flat boar\b to be place\b \fn\ber the jack to
give it firm s\fpport.
. A shovel to \big the vehicle o\ft of snow\brifts.
PARKING BRAKE
When parking in the area where the o\ftsi\be tempera-
t\fre is below 08C (328F) , \bo not apply the parking
brake to prevent it from freezing. For safe parking:
.Place the selector lever in the “P” (Park) position
(A\ftomatic Transmission (AT)/Contin\fo\fsly Vari-
able Transmission (CVT) mo\bel) .
. Place the shift lever in the “1” (1st) or “R”
(Reverse) position (Man\fal Transmission (MT)
mo\bel) .
. Sec\frely block the wheels.
CORROSION PROTECTION
Chemicals \fse\b for roa\b s\frface \beicing are extremely
corrosive an\b will accelerate corrosion an\b the
\beterioration of \fn\berbo\by components s\fch as the
exha\fst system, f\fel an\b brake lines, brake cables,
floor pan an\b fen\bers.
In the winter, the underbody must be cleaned
periodically. For additional information, see
“Corrosion protection” (P.7-5) of this manual.
For a\b\bitional protection against r\fst an\b corrosion,
which may be req\fire\b in some areas, cons\flt a
RENAULT \bealer.
Starting and driving5-39
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-2In case of emergency
If you have a flat tire, follow the in\ftruction\f a\f follow\f.
S\bOPPING VEHICLE
WARNING:
.Be sure to apply the parking brake firmly.
. Be sure to move the shift lever to the “R”
(Reverse) position (Manual Transmission
(MT) model) .
. Be sure to move the selector lever to the “P”
(Park) position. (Automatic Transmission
(AT)/Continuously Variable Transmission
(CVT) model)
. Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazardous.
. Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. \burn on the hazard indicator fla\fher light\f.
3. Park on a level \furface.
4. Apply the parking brake.
5. Automatic \bran\fmi\f\fion (A\b)/Continuou\fly Vari- able \bran\fmi\f\fion (CV\b) model: Move the \felector
lever to the “P” (Park) po\fition.
Manual \bran\fmi\f\fion (M\b) model: Move the \fhift
lever to the “R” (Rever\fe) po\fition.
6. \burn off the engine.
7. Open the hood and \fet up the warning triangle (if equipped):
.\bo warn other traffic.
.\bo \fignal profe\f\fional road a\f\fi\ftance per\fon-nel that you need a\f\fi\ftance.
8. Have all pa\f\fenger\f get out from the vehicle and \ftand in a \fafe place, away from other traffic and
clear of the vehicle.
PREPARING \bOOLS
SCE0902
Rai\fe the back door floor cover.
Your vehicle i\f equipped with either a \fpare tire or an
emergency tire puncture repair kit. Carefully read the
in\ftruction\f provided in the appropriate \fection. .
For model with \fpare tire: See “Changing flat tire
(for model with \fpare tire)” (P.6-2) .
. For model with emergency tire puncture repair kit:
See “Repairing flat tire (for model with emergency
tire puncture repair kit)” (P.6-5) .
CHANGING FLA\b \bIRE (for model with \fpare
tire)
SCE0913
Remove the jack, nece\f\fary tool\f and the \fpare tire
from the \ftorage area.
If \fpacer\f are equipped, remove them before removing
the \fpare tire.
Blocking wheel\f
MCE0001A
FLAT TIRE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
WARNING:
Be sure to block the appropriate wheel to
prevent the vehicle from moving, which may
cause personal injury.
Place suitable blocks
*1at both the front and back of
the wheel diagonall\f opposite the flat tireto
prevent the vehicle from moving when it is \backed up.
Removing wheel cover
SCE0630Type A
SCE0637Type B
Type A:
WARNING:
Never use your hands to remove the wheel
cover. This may cause personal injury.
To remove the wheel cover, use the \back rod
*1as
illustrated.
Appl\f cloth
*2between the wheel and \back rod to
prevent damaging the wheel and wheel cover.
Type B:
Remove the center wheel cap as illustrated.
Removing tire
SCE0903Jack-up points
SCE0914Floor jack-up pointFor the rear, never \back up the vehicle at a location
other than the floor \back-up point that is specified.
WARNING:
. Be sure to read and follow the instructions in
this section.
. DO NOT GET UNDER A VEHICLE THAT IS
SUPPORTED BY A JACK.
. Never use a jack which was not provided
with your vehicle.
. The jack, which is provided with your vehicle,
is designed only to lift your vehicle during a
tire change. Do not use the jack provided
with your vehicle on other vehicles.
. Never jack up the vehicle at a location other
than the jack-up point that is specified.
. Never lift the vehicle more than necessary.
. Never use blocks on or under the jack.
. Never start or run the engine while the
vehicle is on the jack. The vehicle may move
suddenly, and this may cause an accident.
In case of emergency6-3
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-4In case of emergency
.Never allow passengers to remain in the
vehicle while the tire is off the ground.
. Be sure to read the caution label attached to
the jack body before using.Jacking up vehicle
SCE\f5\f4
1. \blace the jack directly under the jack-up point as
illustrated so that the top of the jack contacts the
vehicle at the jack-up point.
The jack should be placed on firm level
ground.
2. Align the jack head between the two notches located at the jack-up point of either the front or
the rear section.
3. Fit the groove of the jack head between the notches as shown.
4. Loosen each wheel nut, counterclockwise, one or two turns with the wheel nut wrench.
Do not remove the wheel nuts until the tire is
off the ground.
5. Carefully raise the vehicle until the clearance between the tire and ground is achieved.
6. To lift the vehicle, securely hold the jack lever and rod with both hands and turn the jack lever.Removing tire
1. Remove the wheel nuts.
2. Remove the damaged tire.
CAUTION:
The tire is heavy. Be sure that your feet are clear
from the tire and use gloves as necessary to
avoid injury.
Installing spare tire
SCE\f576
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
1. If the booster battery is in another vehicle*B,
\fosition the two vehicles*Aand*Bto bring the
batteries into close \fro\bimity to each other.
CAUTION:
If the battery of vehicle*Aequipped with the
Intelligent Key system is discharged, the ignition
switch cannot be moved from the “LOCK”
position and, if the steering lock is engaged,
the steering wheel cannot be moved. Connect
the jumper cables to the booster vehicle
*Bbefore turning the ignition switch and disenga-
ging the steering lock.
2. A\f\fly the \farking brake.
3. Automatic Transmission (AT)/Continuously Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) \fosition.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) \fosition.
4. Switch off all unnecessary electrical systems (headlights, heater, air conditioner, etc.) .
5. Turn the ignition switch to the “LOCK” \fosition.
6. Remove the vent ca\fs, if equi\f\fed, on the battery.
7. Cover the battery with a firmly wrung out moist cloth to reduce the hazard of an e\b\flosion.
8. Connect the jum\fer cables in the sequence as illustrated (
*1,*2,*3,*4).
CAUTION:
.Always connect positive +to positive +and
negative 7to body ground, NOT to the
battery’s negative 7. .
Be sure that the jumper cables do not touch
moving parts in the engine compartment.
. Be sure that the jumper cable’s clamps do
not contact any other metal.
9. Start the engine of the booster vehicle
*Band let
it run for a few minutes.
10. De\fress the accelerator \fedal of the booster vehicle
*Bat about 2,000 r\fm.
11. Start the engine of the jum\fed vehicle
*Ain the
normal manner.
CAUTION:
. Never keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, turn the ignition switch
“OFF” and wait at least 10 seconds before
trying again.
. If the starter motor does not start by pushing
the ignition switch, push the ignition switch
to the OFF position before trying again.
12. After the engine is started, carefully disconnect the jum\fer cables in the o\f\fosite sequence from
that illustrated (
*4,*3,*2,*1).
13. Remove and dis\fose of the cloth as it may be contaminated with corrosive acid.
14. Re\flace the vent ca\fs, if removed.
NOTE:
. For model with Stop/Start (Idling Stop)
System, use the special battery that is
enhanced in regard to the charge-discharge
capacity and life performance. Avoid using a
non-special battery for the Stop/Start (Idling
Stop) system, as this may cause early deterioration of the battery or a malfunction
of the Stop/Start (Idling Stop) system. For
the battery, it is recommended to use
Genuine RENAULT parts. For more informa-
tion, contact a RENAULT dealer.
. For model with Stop/Start (Idling Stop)
System, it may take some time until Stop/
Start (Idling Stop) System activates when
the battery is replaced or the battery term-
inal is disconnected for extended periods
and then reconnected.
In case of emergency6-9
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-2Maintenance and do-it-yourself
Your new vehicle has been desi\fned to have minimum
maintenance requirements with lon\f service intervals
to save \bou both time and mone\b. However, some da\b-
to-da\b and re\fular maintenance is essential to maintain
\bour vehicle’s fine mechanical condition, as well as its
emission and en\fine performance.
It is the owner’s responsibilit\b to make sure that the
specified maintenance, as well as \feneral mainte-
nance, is performed.
As the vehicle owner, \bou are the onl\b one who can
ensure that \bour vehicle receives the proper main-
tenance care. You are a vital link in the maintenance
chain.
SCHEDULED MAINTENANCE
For \bour convenience, the required scheduled main-
tenance items are described and listed in a separate
maintenance booklet. You must refer to that booklet to
ensure that necessar\b maintenance is performed on
\bour vehicle at re\fular intervals.
GENERAL MAINTENANCE
General maintenance includes those items which
should be checked durin\f normal da\b-to-da\b operation
of the vehicle. The\b are essential if \bour vehicle is to
continue to operate properl\b. It is \bour responsibilit\b to
perform these procedures re\fularl\b as prescribed.
Performin\f \feneral maintenance checks requires
minimal mechanical skill and onl\b a few \feneral
automotive tools.
These checks and inspections can be done b\b
\bourself, a qualified technician, or if \bou prefer, a
RENAULT dealer.
WHERE TO GO FOR SERVICE
If maintenance service is required or \bour vehicle
appears to malfunction, have the s\bstems checked and
tuned b\b a RENAULT dealer.
RENAULT technicians are well-trained specialists and
are kept up-to-date with the latest service information
throu\fh technical bulletins, service tips, and internal
dealership trainin\f pro\frams. The\b are completel\b
qualified to work on RENAULT’s vehiclesbeforethe\b
work on \bour vehicle, rather than after the\b have
worked on it.
You can be confident that a RENAULT dealer’s service
department performs the best job to meet the
maintenance requirements on \bour vehicle — in a
reliable and economic wa\b. Durin\f normal da\b-to-da\b operation of the vehicle,
\feneral maintenance should be performed re\fularl\b as
prescribed in this section. If \bou detect an\b unusual
sounds, vibrations or smells, be sure to check for the
cause or have a RENAULT dealer do it promptl\b. In
addition, \bou should notif\b a RENAULT dealer if \bou
think that repairs are required.
When performin\f an\b checks or maintenance work,
closel\b observe “Maintenance precautions” (P.8-4) .
EXPLANATION OF GENERAL MAINTE-
NANCE ITEMS
Additional information on the following items
with
“*”is found later in this section.
Outside vehicle
The maintenance items listed here should be per-
formed from time to time, unless otherwise specified.
Doors and engine hood:
Check that all doors and the en\fine hood operate
properl\b. Also make sure that all latches lock securel\b.
Lubricate hin\fes and latches if necessar\b. Make sure
that the secondar\b latch of the en\fine hood keeps the
hood from openin\f when the primar\b latch is released.
When drivin\f in areas usin\f road salt or other
corrosive materials, check lubrication frequentl\b.
Lights*:
Clean the headli\fhts on a re\fular basis. Make sure that
the headli\fhts, stop li\fhts, tail li\fhts, turn si\fnal li\fhts,
and other li\fhts are all operatin\f properl\b and installed
securel\b. Also check the aim of the headli\fhts.
MAINTENANCE REQUIREMENTS GENERAL MAINTENANCE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-4Maintenance and do-it-yourself
Window washer fluid*:
Check that there is adequate fluid in the reser\foir.
M\bINTEN\bNCE PREC\bUTIONS
When performing any inspection or maintenance work
on your \fehicle, always take care to pre\fent serious
accidental injury to yourself or damage to the \fehicle.
The following are general precautions which should be
closely obser\fed.
WARNING:
.Park the vehicle on a level surface, apply the
parking brake securely and block the wheels
to prevent the vehicle from moving. Move
the selector lever to the “P”(Park) position
or the shift lever to the “N”(Neutral) position.
. Be sure the ignition switch is in the “OFF”or
“LOCK” position when performing any parts
replacement or repairs.
. Do not work under the hood while the
engine is hot. Always turn off the engine
and wait until it cools down.
. If you must work with the engine running,
keep your hands, clothing, hair and tools
away from moving fans, belts and any other
moving parts.
. It is advisable to secure or remove any loose
clothing and any jewelry, such as rings,
watches, etc. before working on your vehi-
cle.
. If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to
escape. .
Never get under the vehicle while it is
supported by a jack.
. Keep smoking materials, flame and sparks
away from fuel and the battery.
. Never connect or disconnect either the
battery or any transistorized component
connector while the ignition switch is in the
“ON” position.
. On gasoline engine models with the Multi-
port Fuel Injection (MFI) system, the fuel
filter and fuel lines should be serviced by a
RENAULT dealer because the fuel lines are
under high pressure even when the engine is
turned off.
. Your vehicle is equipped with an automatic
engine cooling fan. It may come on at any
time without warning, even if the ignition
switch is in the “OFF” position and the
engine is not running. To avoid injury, always
disconnect the negative battery cable before
working near the fan.
. Always wear eye protection whenever you
work on your vehicle.
. Never leave the engine or the transmission
related component harness connector dis-
connected while the ignition switch is in the
“ON” position.
. Avoid direct contact with used engine oil and
coolant. Improperly disposed engine oil,
engine coolant, and/or other vehicle fluids
can hurt the environment. Always conform to
local regulations for disposal of vehicle
fluids.
This “8. Maintenance and do-it-yourself” section
pro\fides instructions regarding only those items which are relati\fely easy for an owner to perform.
You should be aware that incomplete or improper
ser\ficing may result in operating difficulties or ex-
cessi\fe emissions, and could affect your warranty
co\ferage.
If in doubt about any servicing, have it
done by a RENAULT dealer.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
8-14Maintenance and do-it-yourself
Engine oil and filter replacement \fK9K engine
model)
\bDI2472
1. Oil drain plug
2. Oil filter
1. Place a large drain pan under the drain plug.
2. Remove the drain plug with a wrench.
3. Remove the oil filler cap and completely drain the oil.
If the oil filter is to be changed, remove and
replace it at this time.
CAUTION:
Waste oil must be disposed of properly. Check
your local regulations.
4. Loosen the oil filter with an oil filter wrench.
5. Remove the oil filter by turning it by hand.
6. Wipe the entire oil filter mounting surface with aclean cloth.
Be sure to remove any old gasket remaining on the
mounting surface. 7. Apply new engine oil to the gasket on the new oil
filter.
8. \bcrew in the oil filter until a slight resistance is felt, and then tighten an additional 3/4 of a turn to
secure the filter.
Oil filter tightening torque:16 to 20 N·m (1.6 to 2.0 kg-m, 12 to 15 ft-lb)
9. Clean and reinstall the drain plug and new washer. \becurely tighten the drain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:16 to 24 N·m (1.6 to 2.4 kg-m, 12 to 18 ft-lb)
10. Refill the recommended engine oil and quantity. \f\bee “Recommended fuel/lubricants and capaci-
ties” \fP.9-2) .)
11. \becurely install the oil filler cap.
12. \btart the engine.
13. Check the drain plug and the oil filter for any sign of leakage.
14. Dispose of the used oil in the proper manner. Check your local regulations.
15. Check the engine oil level according to the proper procedure. \f\bee “Checking engine oil level” \fP.8-
10) .)
After operation
1. Install the engine undercover \fif removed) intoposition as the following steps.
a. Pull the center of each plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clips through the undercover into thehole in the frame, then push the center of the
clips in to lock the clips in place. d. \bcrew in the bolts, then tighten them.
2. Lower the vehicle carefully to the ground.
PROTECT ENVIRONMENT
It is illegal to pollute drains, watercourses and soil. Use
authorized waste collection facilities, including civil
amenity sites and garages providing facilities for
disposal of used oil and used oil filters. If in doubt,
contact your local authority for advice on disposal.
The regulations concerning the pollution of the
environment will vary from country to country.
&RQGLWLRQ