2012 RENAULT MEGANE RS ECU

JauneNoirNoir texte
5.5
ENG_UD18914_3
Kit de gonflage (X61 - X95 - B95 - D95 - L38 - X38 - X32 - B32 - Renaul\
t)
ENG_NU_837-6_BDK95_Renault_5
tyre Pressure KIt (3/3)
– affix driving recommendation label 9
to the dashboard where it can easily
be seen by the driver;
– store the kit;
– start the engine straight away and,
after driving a maximum of approx -
imately 2 miles (3 kilometres) or
10 minutes , stop and check the
pressure using the inflation kit. If it is
above 1.3 bar, adjust it to the rec -
ommended pressure (refer to the
label affixed to the edge of the driv-
er’s door), otherwise contact an ap-
proved dealer: repair is not possible.
n ote: after using the inflation kit, you
should visit an approved Dealer to re -
place the inflation hose and the bottle
of repair product.Precautions when using the
kit
The kit should not be operated for more
than 15 consecutive minutes.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addi -
tion, reduce your speed and
under no circumstances exceed 48
mph (80 km/h). The sticker, which
you must affix in a prominent posi -
tion on the dashboard, reminds you
of this.
Depending on the country or local
legislation, a tyre repaired with the
tyre pressure kit will need to be re-
placed.
Nothing should be placed
around the driver ’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
9
8
Once the tyre is inflated correctly:
– stop using the kit;
– close the integrated cap on the bottle
again;
– disconnect adapter 8;
Please be aware that a poorly tightened or missing valve cap can make
the tyres less airtight and lead to pressure loss.
Always use valve caps identical to those fitted originally and tighten them
fully.

tool kit ................................................... (up to the end of the DU)
hubcap tool ........................................... (up to the end of the DU)
jack ....................................................... (up to the end of the DU)
puncture ................................................ (up to the end of the DU)
wheelbrace ........................................... (up to the end of the DU)
trims ...................................................... (up to the end of the DU)
emergency spare wheel ....................... (up to the end of the DU)
wheelbrace ............................................................ (current page)
5.6
ENG_UD18915_3
Bloc-outils (X95 - B95 - D95 - Renault)
ENG_NU_837-6_BDK95_Renault_5
Tool kit (jack, wheelbrace, etc.)
Hubcap
t OOl KIt/wheel trIm – wheel
The tool kit is located in the luggage
compartment: lift the carpet.
The tools included in the tool kit depend
on the vehicle.
wheelbrace 1
Jack 2
When replacing the jack, fold it cor -
rectly and position the wheelbrace cor-
rectly before replacing it in its position.
hubcap tool 3
This tool is used to remove the wheel
trims.
wheel bolt guide 4
To finish loosening or starting to tighten
the wheel bolts.
t owing hitch 5
Refer to the information on “Towing” in
Section 5.
Do not leave the tools unsecured inside the vehicle as they may come
loose under braking. After use, check that all the tools are correctly
clipped into the tool kit, then position it correctly in its housing: there is a
risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for the emergency
spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances
should it be used for carrying out repairs underneath the vehicle or to gain access
to the underside of the vehicle.
2
1
3
5
wheel trim
Remove it using the hubcap tool 3 by
connecting the hook in the recess pro-
vided next to the valve 6 (to attach the
metal clip).
To refit wheel trim, align it with valve 6.
Push the retaining hooks in fully, start-
ing with side B near the valve, followed
by C and D, finishing at E opposite the
valve.
n ote: if you are using anti-theft bolts,
refer to the information on “Changing a
wheel”.
6
B
cD
e
4

4 SIMPLE ACTIONS*
FOR YOUR SAFETY
* Warning: these actions do not constitute an exhaustive list. Refer to you\
r Driver’s Handbook for more information.
• Always fasten your seat belt,– even for short journeys– even if your vehicle is fitted with air bags.
• Make sure that all passengers have fastened their seat belts, even in the back.
• Always secure children using devices suitable for their size and weight (seat, shell seat, etc.).
• Important! If the vehicle is fitted with front passenger air bags which can be disconnected, disconnect them before installing a rear-facing baby seat.
• Place heavy objects or luggage at the back of the luggage compartment.
• Distribute the load between the right-hand and left-hand sides in the loading area when transporting goods.
• Adjust the height of the seat belt according to your size.
• Adjust the angle of your seatback ensuring that the seat belt remains in contact with your body.
• Adjust the height of the headrest: headrest height = top of your head.Headrest as close as possible to the head.

4
1
2
3