Page 10 of 168
Familiarisation
8
Instruments and controls
1. Steering lock and ignition switch.2.
Wiper stalk. 3.
Windscreen demisting vents.
4.
Glove box.Passenger's airbag deactivation.5.
Bonnet release lever.
6.Parking brake.
7. Drive selector. 8.12 V accessory socket. 9.
Heating / air conditioning controls.10.Emergency or assistance call.11.
Hazard warning switch.12 .Centre vents. 13.Audio system.
Page 16 of 168
Familiarisation
14
Monitoring
1.
With the ignition on, the orange and red
warning lamps come on.2. With the engine running, these warninglamps go off.
I
f a warning lamp remains on, refer to the relevant page.
Warning lamps
19A
. "Neutral" position.
B. Energy consumptionC.
"Eco" zone.D."Charge" zone.
Energy consumption /
generation indicator
27
Four successive aler ts indicate that the energy
available in the main battery is dropping to a
low level:
- 2 bars of the energy gauge in the
instrument panel, on and
flashing :
starting to use the reser ve.
- The last bar in the energy gauge flashing.
- The last bar disappears:
display of the range disappears; the heatingand air conditioning are switched off.
Low energy alerts
- Display of this warning lamp in
the instrument panel:
Progressive reduction in the
power available from the motor.
26
Page 17 of 168
.Familiarisation
15
Driving safely
P.
Parking.
Press the brake pedal to come out of this
position. R.Reverse. N. Neutral. D.Drive (forward).
Drive selector
55- Check that the drive selector is in position
P.P- Inser t the key in the ignition switch.
- Turn the key to position 4 (START).- Hold it in this position for a few seconds,until the " READY" lamp comes on,
accompanied by an audible signal.
- Release the key.
The switch returns automatically to
position
3 (ON) .
Starting the motor
53
- Stop the vehicle.
- Keep your foot on the brake pedal.
- Put the drive selector in position P
. P
- Apply the parking brake.
- Turn the key anti-clockwise to the LOCKposition.
Stopping the motor
53
Page 21 of 168
1
Instruments and controls
19
Indicator and warning lamps
Visual indicators informing the driver that asystem is in operation, is deactivated or has a
fault.
When the ignition is switched on
Cer tain warning lamps come on for a few seconds
when the vehicle's ignition is switched on.
These same warning lamps go off after a fewseconds.
If you notice one of these warning lamps
remaining on, refer to the information on the
warning lamp in question.
Associated warnings
The illumination of cer tain warning lamps may
be accompanied by an audible signal.
The warning lamps may come on continuously (fixed) or flash.
Cer tain warning lamps may come on in one of two modes. Only by relating the type of lighting to the operating status of the vehicle can it be ascertained whether the situation is normal or whether a fault has occurred.
Page 27 of 168
1
Instruments and controls
25
Warning / indicator lampStateCauseAction / Observations
Airbags
On temporarily. When you switch on the ignition, this
warning lamp comes on for a few seconds, then goes off. If it does not
go off, contact a PEUGEOT dealer or a qualified workshop.
On fixed. Fault with one of the airbag or seat
belt pretensioner systems. Have it checked by a PEUGEOT dealer or a qualified
workshop.
Protection system for themain battery
On fixed. The state of charge of the main battery is too low or the temperature
of the main battery is too low... The power
from the motor is limited.
Charge the main battery as soon as possible.
If the warning lamp does not go off, contact a
PEUGEOT dealer or qualified workshop.
Self-diagnosis system of the main electricalcircuit
On fixed. Fault in the main electrical circuit. You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Front seat beltnot fastened / unfastened
On fixed, then
flashing, accompanied
by an audible signal.The driver and/or the front passen
ger has not fastened or has unfastenedtheir seat belt. Pull the strap, then inser t the ton
gue in the buckle.
Right hand rear seatbelt unfastened
On fixed. The right hand rear passenger hasunfastened their seat belt.
Pull the strap then inser t the ton
gue in the buckle.Left hand rear seat beltunfastened
On fixed. The left hand rear passenger hasunfastened their seat belt.
Page 29 of 168
1
Instruments and controls
27
Energy consumption / generation indicator
Energy consumption
On switching on the ignition, your vehicleneither consumes nor generates energy in itselectric traction system: the needle is in the
"neutral" position (provided that the heating and
air conditioning are off).
"Eco" zone
A system that informs the driver of the level of energy consumption or generation of the main battery.
"Neutral" position
"Char
ge" zone
The needle moves to the right in proportion to
the energy consumption by the vehicle. The needle is in this zone when the vehicle is
used so as to moderate electric consumption
and optimise its ran
ge.
The needle moves to the le
ft in propor tion to
the level of charge sent to the main battery,
during period of deceleration and braking.
Page 30 of 168
Instruments and controls
28
Instrument panel screen When the ignition switch is in the " ON
" position, press button A
repeatedly to display the following information in turn.
Distance recorder
System for measuring the total distance
travelled by the vehicle during its life.Press button A.The total distance appears in the screen.
Reset to zero
With the ignition on and either trip Aor Bdisplayed, press the button for more than
2 seconds.
Trip distance recorder (Trip A or B)
Each of these trip recorders indicates thedistance travelled since the last reset.
Press button A to display the desired trip.
Page 31 of 168
1
Instruments and controls
29
Service indicator
When the ignition is switched on, pressbutton A
several times in succession until the
ser vice indicator is displayed in the desiredunits. This point can be indicated in one o
f two ways:
- the miles (km) remaining,
- the time remaining to the next ser vice.
Operation
1.
The screen indicates that 620 miles (10 0 0 km) or 1 month remain before thenext service. 2.The screen indicates that the date for theservice has been exceeded.
Every time the ignition is switched on,
the ser vice spanner is displayed for a
few seconds to remind you that a ser vice should be carried out as soon as possible.3.Once the ser vice has been carried out, the
distance or the number of months to the next ser vice is displayed again.
System which informs the driver when the next service is due in accordance with the
manufacturer's servicing schedule.
The point at which the next ser vice is due is calculated from the last service indicator zeroreset.
S
ystem for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
With the lighting on or off, press button Ato select the function, then hold down to change
the intensity of the lighting of the instruments
and controls in "day" or "night" mode.
The intensity of the lighting increases each timebutton Ais pressed.
When the lighting reaches the maximumsetting, press again to change to the minimum setting.
When the lighting reaches the required
intensity, release button A .
The setting is saved when you release button A
and retained when the ignition switch is turned
to OFF.
Lighting dimmer
