2012 Peugeot 508 RXH instrument panel

80
!
Access
) Press this button C
to close thetailgate electrically.
Do not hinder closin
g of the tailgate: any
obstacle to closing causes the tailgate to stopand rise a few centimetres automatically.
To close the tailgate manually: move the
tailgate slightly up then down to disengage it
from its drive then lower it until closed.
To avoid the risk of injury, ensurethat no one is close to the rear of thevehicle when opening or closing the tailgate.

While electric opening or closing of the tailgate
is in progress, you can stop its movement at
any time: ) press the interior button or button A
on
the remote control or button Bor C on thetailgate.


Stopping the opening
or closing
Ad
justing the opening
hei
ght
"Boot open" warning
With the hybrid system active or when the
vehicle is moving, if the tailgate is not properly closed, a message accompanied by an audiblesignal (from 6 mph (10 km/h)) is displayed in the
instrument panel screen.
The maximum openin
g height of the tailgate can be set and memorised (restricted overheadclearance, ...).
This memorisation is done in two steps,
b
y successive presses on button C:

- during opening, a first press stops the
tailgate at the desired height,

- a second maintained press memorises theposition of the tailgate; an audible signal confirms the memorisation.
To delete this memorisation, make a new
maintained press until the audible signal isheard.

84
i
Access
Low fuel level

When the low fuel level in the
tank is reached, this warning lamp comes on in the instrument panel,
accompanied by an audible warning
and a message in the instrument
panel screen.
When it first comes on, around 7 litresof fuelremain in the tank.
You must refuel as soon as possible to avoid
running out.
Fuel supply cut-off
Your vehicle is equipped with a safety device
which cuts off the fuel supply in the event of a collision.


It is still possible to use a fuel can to fill
the tank but this must be done slowly. In order to ensure a good flow of fuel, do not place the nozzle of the fuel canin direct contact with the flap of themisfuel prevention device.


Diesel misfuel prevention

Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of engine damage that can result from filling with the wrong fuel.
Located in the filler neck, the misfuel prevention device appears when the filler cap is removed.
When a petrol
filler nozzle is introduced into the fuel filler neck of your Diesel vehicle, it comes
into contact with the flap. The system remains
closed and prevents filling. Do not persist but introduce a Diesel filler
nozzle.

Operation



Tr a v e l l i ng abroad
As Diesel fuel pump nozzles may be different
in other countries, the presence of the misfuel prevention device may make refuellingimpossible.
Before travelling abroad, we recommend that you check with the PEUGEOT dealer network,
whether your vehicle is suitable for the fuelpumps in the country in which you want to
travel.

3
97
i
Comfort











Peugeot Connect USB
This connection box, consisting of a JACKauxiliary socket and a USB port, is located in
the front armrest (under the cover).
It permits the connection of por table device,
such as a di
gital audio player of the iPod® type®
or a USB memory stick.
It reads the audio file formats (MP3, OGG,WMA, WAV, ...) which are transmitted to your audio equipment and played via the vehicle's
speakers.
You can mana
ge these files using the steeringmounted controls or the audio system control
panel and display them in the instrument panel screen.
When the USB por t is used, the por table device
charges automatically.


For more information on the use of this system, refer to the "Audio andTelematics" section.
Ski flap

Device for storing and transporting long
objects.

Opening
)Lower the armrest. )Press the flap opening control.)Lower the flap. )Load the objects from inside the boot.

3
117
i
Comfort
Programmable heating mode
This is an additional and separate system
which heats the engine hot water circuit
to improve defrosting and to preheat thepassenger compartment.
This indicator lam
p comes on if the
system is programmed in preheatingmode.With the i
gnition on, press the left hand
steering mounted thumb wheel for access to
the main menu:
Programming
) In the "Main menu", select "Pre-heating/Pre-ventilation",
)
Select "Activation" and if necessary for programming, "Parameters",
)
Select "Heating" to preheat the engine or passenger compar tment or "Ventilation" to
ventilate the passenger compartment,
) Select:
- immediate to star t the heating ("OK"
once),
- the first clock to programme/store astar ting time,
- the second clock to programme/storeanother starting time.










Programmable Heating/ Ventilation


Programmable Ventilation
mode

This mode allows ventilation of the passenger compartment to improve the temperatureexperienced on entering the vehicle in summer.

Using these two clocks and according to season you can, for example, selectone or the other star ting time. A message in the instrument panel
screen confirms your choice.

118
!
!
Driving
It is recommended that you do not apply the parking brake in very cold conditions (ice) and during towing
(recovery, ...). Deactivate the automatic functions and release the parking brakemanually.



Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and the control lever Aare on, not flashing.

The electric parking brake combines
2 operating modes:- Automatic Application/ReleaseApplication is automatic when the engine
stops, release is automatic on use of the
accelerator (this mode is activated by
default), -Manual Application/ReleaseManual application of the parking brake is done by pulling control lever A.Manual release is done by pushing andreleasing the control lever, while pressing
the brake pedal.
When the driver's door is opened, there is an
audible signal and a message is displayed if the
brake is not applied.



Programming the mode

Depending on the country of sale of the vehicle,
the automatic application when the engine isswitched off and the automatic release whenyou press the accelerator can be deactivated. With the vehicle stationary, to apply the parking
brake whether the h
ybrid system is active or off,
pull
control lever A.


Manual application

Activation/deactivation is done via
the menu in the instrument panel
screen.
The parkin
g brake is then applied and released
manually. The application o
f the parking brake is confirmed by:


- illumination o
f the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
When the driver’s door is opened with the
hybrid system active, there is an audible signal
and a message is displayed if the parking brakehas not been applied.








Electric parking brake

If this warning lamp comes on in the
instrument panel, the automatic mode
i
s deactivated.

4
119
!
i
Driving
With the ignition on or the hybrid system active,
to release the parking brake, pressthe brakepedal
, pull
then release control lever A.
The full release of the parking brake is confirmed by:


Manual release



- the braking warning lamp and of
the P warning lamp in the controllever Agoing off,

- displa
y of a message.
I
f you pull the control lever Awithout pressing
the brake pedal, the parking brake will not
be released and a message appears in the
instrument panel.If necessar
y, you can make a maximumapplicationof the parking brake. It is obtained
by means of a long pullon control lever A,
until you see a message and an audible signal is heard. Maximum application is essential:- in the case of a vehicle towing a trailer,
if the automatic functions are activatedbut you are applying the parking brake
manually,
- when the slope you are parked on may
vary (e.g. on a ferry, on a lorry, during
towing).
Maximum application

Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and in the controllever A
are on fixed (not flashing).

Never leave a child alone inside thevehicle with the ignition on, as they could release the parking brake.



Automatic application,
engine off



- illumination of the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
With the vehicle stationary, the parking brakeis automatically applied when the engine is
switched off. The application of the parking brake isconfirmed by:
In the case of towing, a loaded vehicleor parking on a gradient, make a maximum application of the parkingbrake then turn the front wheels towards the pavement and engage a gear whenyou park.
After a maximum application,the release time will be longer.

120
!
!
Driving
Automatic release
The electric parking brake releasesautomatically and progressively with the
movement of the vehicle,select position A, Mor Rthen press the accelerator.
Full release of the parking brake is confirmed by:


- the brakin
g warning lamp and of
the Pwarning lamp in the control lever Agoing off,

- displa
y of a message.


When stationary, with the hybrid systemactive, do not press the accelerator pedal unnecessarily, as you mayrelease the parking brake.
Before leaving the vehicle, check thatparking brake warning lamps in theinstrument panel and the control lever Aare on fixed, not flashing.



Immobilising the vehicle,
hybrid system active
With the hybrid system active and the vehicle
stationary, in order to immobilise the vehicle
it is essential to manually
apply the parkingbrake by pullingcontrol lever A.
The application of the parking brake isconfirmed by:
- illumination o
f the braking warning
lamp and of the Pwarning lamp in
the control lever A ,
- display of a message.
When the driver’s door is opened, a loud beep
is heard and a messa
ge is displayed if the
parking brake has not been applied.

Particular situations

In cer tain situations (e.g. star ting the engine),
the parking brake can automatically alter itsforce. This is normal operation.
To advance your vehicle a few centimetres
without star ting the engine, but with the ignition
on, press on the brake pedal and release the
parking brake by pushing then releasingcontrol lever A
. The full release of the parkingbrake is confirmed by the warning lamps in
the control lever Aand in the instrument panel going off and display of a message.
If a parking brake fault occurs while applied
or
if the battery runs flat, an emergency release is
always possible.
In order to ensure correct operation and
so your safety, the number of successive
application/release operations of the parkin
g
brake is limited to eight.
In the event of abuse, you are aler ted by a message and a warning lamp which flashes.

122
!
!
Driving
)Fold the 2/3 par t of the rear seat for access
to the green cap.

For reasons of safety you must contact a PEUGEOT dealer as soon as possible to have the cap replaced.
Take care not to place anything dusty or
wet close to the cap.
With an emergency release,immobilisation of the vehicle is no longer be assured once the mechanical release has started and the mechanical tool cannot be used to apply the parkingbrake again.
Do not carry out any action on lever A
,or stop/star t the system while therelease tool is engaged.
Have it checked by a PEUGEOT dealer or a qualified workshop.
To r e - e ngage the electric parking brake(after correction of the fault or battery failure), make a long pull on the controllever Auntil the parking brake warninglamp (!) flashes in the instrument panel, then make a second long pull until this warning lamp comes on fixed (notflashing).
)
Turn the release tool clockwise
. For
reasons of safetyit is essentialto keep
turning until the stop is reached. The
parking brake is released.) Take care to refit the release tool in its
housing.) The operation of the parking brake is
reinitialised each time the ignition is switched off and on. If reinitialisation of the
parking brake is not possible, contact a
PEUGEOT dealer.) The application time may be longer than
with normal operation.
) Pierce the cap and inser t the release tool in
the tube.



The emergency braking should only be used in exceptional circumstances.