2012 Peugeot 508 RXH ECO mode

3
111
Comfort





Quad-zone digital air conditioning


Automatic operation


1. Automatic comfort programme

The Soft/Auto/Fast modes allow the driver
and front seat passenger to select their
desired comfor t settings for the passenger compartment:
2. Activating/deactivating the rear air conditioning


3 - 4. Driver-passenger side
adjustment

The driver and front passenger can each adjust
the temperature to their requirements.
The value indicated on the display corresponds
to a level of comfor t and not to a temperature in
de
grees Celsius or Fahrenheit.
Favours optimum gentle and silent
operation by limiting the air flow.
Offers the best compromise between
thermal comfort and silence of
operation.
Favours d
ynamic and effective air
flow. Pr
ess this button to deactivate the
rear air conditioning and lock thesystem. A padlock appears in the
L
CD screen. When the rear system is reactivated, automatic mode is selected with
the last temperature settings used.
)
Turn control 3
or 4
to the left (blue) or to the right (red)respectively to decrease or
increase this value.
A setting around the value 21 provides optimumcomfort. However, depending on your requirements,
a setting between 18 and 24 is normal. It is recommended that the difference between
left and right should not be greater 3. The air conditionin
g can only operate when the hybrid system is active, except in STOP mode of Stop & Star t.

114
Comfort
Adjusting the rear passenger comfort level
1. Automatic comfort programme
) Press the "AUTO"
button. The lamp in the button comes on.
We recommend that you use this mode. It automatically adjusts all settings to provide
optimum operation for the comfor t level chosen: passenger compar tment temperature, air flowand air distribution.
This system is designed to operate effectivelyin all seasons, with the windows closed.

2. Air distribution adjustment
3. Temperature adjustment, leftand right

Press the corresponding button
successivel
y for: The le
ft and rear passengers can each adjust
their temperature setting independently.
The value indicated in the screen is a level
of comfor t and not a temperature in degreesCelsius or Fahrenheit.
) Turn the dial to the left to lower the
value and to the right to raise it. - F
ootwell and centre vent.
-
Centre vent.
- A
utomatic control of air distribution. The rear air conditionin
g controls only operate
if, from the front:
- th
e REARbutton is activated,
- the automatic visibilit
y programme is notactivated.

A setting around 21 provides an optimum
level of comfor t. However, depending on your
requirements, a setting between 18 and 24 isnormal.
It is recommended that the difference between
left and right should not be greater 3.
Ensure that the air grilles and vents on the floor are not obstructed.

3
117
i
Comfort
Programmable heating mode
This is an additional and separate system
which heats the engine hot water circuit
to improve defrosting and to preheat thepassenger compartment.
This indicator lam
p comes on if the
system is programmed in preheatingmode.With the i
gnition on, press the left hand
steering mounted thumb wheel for access to
the main menu:
Programming
) In the "Main menu", select "Pre-heating/Pre-ventilation",
)
Select "Activation" and if necessary for programming, "Parameters",
)
Select "Heating" to preheat the engine or passenger compar tment or "Ventilation" to
ventilate the passenger compartment,
) Select:
- immediate to star t the heating ("OK"
once),
- the first clock to programme/store astar ting time,
- the second clock to programme/storeanother starting time.










Programmable Heating/ Ventilation


Programmable Ventilation
mode

This mode allows ventilation of the passenger compartment to improve the temperatureexperienced on entering the vehicle in summer.

Using these two clocks and according to season you can, for example, selectone or the other star ting time. A message in the instrument panel
screen confirms your choice.

118
!
!
Driving
It is recommended that you do not apply the parking brake in very cold conditions (ice) and during towing
(recovery, ...). Deactivate the automatic functions and release the parking brakemanually.



Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and the control lever Aare on, not flashing.

The electric parking brake combines
2 operating modes:- Automatic Application/ReleaseApplication is automatic when the engine
stops, release is automatic on use of the
accelerator (this mode is activated by
default), -Manual Application/ReleaseManual application of the parking brake is done by pulling control lever A.Manual release is done by pushing andreleasing the control lever, while pressing
the brake pedal.
When the driver's door is opened, there is an
audible signal and a message is displayed if the
brake is not applied.



Programming the mode

Depending on the country of sale of the vehicle,
the automatic application when the engine isswitched off and the automatic release whenyou press the accelerator can be deactivated. With the vehicle stationary, to apply the parking
brake whether the h
ybrid system is active or off,
pull
control lever A.


Manual application

Activation/deactivation is done via
the menu in the instrument panel
screen.
The parkin
g brake is then applied and released
manually. The application o
f the parking brake is confirmed by:


- illumination o
f the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
When the driver’s door is opened with the
hybrid system active, there is an audible signal
and a message is displayed if the parking brakehas not been applied.








Electric parking brake

If this warning lamp comes on in the
instrument panel, the automatic mode
i
s deactivated.

136
!
Driving
) Press 1
, the cruise control is activatedbut remains paused.
)
Set the programmed speed by
accelerating to the required speed,
then press button 2 or 3(e.g.: 70 mph (11 0 k m / h)).
Programming
You can then change the programmed speed using buttons 2
and 3
:
- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press. )Pause the cruise control by pressing button 4
: the screen confirms the suspension with with "Pause".)Switch the cruise control back on by pressing button 4
again.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results
in flashing of this speed on the display.
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels theflashing of the speed.
When the cruise control is switched on, be careful if you maintain the pressure on one of the programmed speed changing buttons: this may result in a very rapid change in the speed of your vehicle. Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise control will not be able to prevent the vehiclefrom exceeding the programmed speed. To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.
In the event o
f a cruise control fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.


Operating fault
Off/Return to normal drivin
g
)Press 5 ; cruise control mode is deactivated The screen returns to
the distance recorder.

144
i
i
i
Visibility

Lighting left on audible signal
An audible signal when a front door is opened warns the driver that the vehicle's exterior lighting is on, with the ignition off and in manual lighting mode.
In this case, switching off the lighting stops the audible signal.
With the ignition off, if the dippedheadlamps remain on, the vehicle goes into "ECO" mode to avoid dischargingthe battery.

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of theglass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.

Daytime lighting, compulsory in cer tain
countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other road users.
Daytime running lamps

This function is assured:


- in countries where it is imposed byregulations, by illumination of the dippedbeam headlamps with the sidelamps and number plate lamps.

- for other countries where it is provided, by
the use of dedicated lamps.

This function can be activated or deactivated via the vehicleconfiguration menu.



The lighting goes off when you switchoff the ignition, but you can always switch it on again using the lightingcontrol stalk.


*

f
unction that can be set in the vehicle
configuration menu.
LED lamps

They come on when the engine is started.
Depending on the destination country, they are used for:


- daytime running lamps *
in day mode andsidelamps in night mode (they are brighter
when daytime running lamps),
or


- sidelamps in day and night mode.
Where LED lamps are fitted, the filament bulbs
for the da
ytime running lamps/sidelamps in the front lamp units are not used.

5
155
i!
Visibility
1.Front cour tesy lamp2.Front map reading lamps 3.Rear map reading lamp s4.Interior mood LEDs












Courtesy lamps
In this position, the cour tesy lamp comes on gradually:
Front courtesy lamps

Take care to avoid leaving anything in contact with the cour tesy lamps.
With the "permanent lighting" mode, the lighting time varies according to the circumstances: - with the ignition off, approximatelyten minutes, - in energy economy mode, approximately thirty seconds,-with the hybrid system active, unlimited.
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when opening a door,
- when the remote control locking button is
activated, in order to locate your vehicle.
It switches off
gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed.
Permanentl
y off.

Permanent lighting.


Front and rear map reading
lamps
)
With the ignition on, press the
corresponding switch.
When the front courtesy lamp is on "permanent
lighting", the rear map reading lamp comes on
as well, unless it is "permanentl
y off".
From the front, you can deactivate the rear map
reading lamps so as to not disturb sleeping
rear passengers, for example. However, the
rear passengers can force the illumination of
a lamp.

8
191
!!i
Practical information
The headlamps are fitted with
polycarbonate glass with a protectivecoating:)do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,)
use a sponge and soapy water, )
when using a high pressure washer on persistent marks, do not keep the lance directed towards thelamps or their edges for too long, so as not to damage their protectivecoating and seals.
Risk of electrocution
Xenon bulbs (D1S-35W) must bereplaced by a PEUGEOT dealer or aqualified workshop.
)Do not touch the bulb directly withyour fingers, use lint-free cloths. Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of serious burns). It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.









Dipped and main beamheadlamps (xenon model)

D1S xenon bulbs must be changedby a PEUGEOT dealer or a qualifiedworkshop, as there is a risk of electrocution.
It is recommended that the D1S bulbsare changed at the same time when oneof them fails.
Direction indicators (Xenon model)
Daytime running lamps

For the replacement of these light-emitting diode (LED) lamps, contacta PEUGEOT dealer or a qualified
workshop.