Page 98 of 304
96
Comfort
Automatic day/night model
By means of a sensor, which measures thelight from the rear of the vehicle, this system
automatically and progressively changes between the day and night uses.
Adjustable mirror providing a central rear ward
view.
Equipped with an anti-dazzle system, which
darkens the mirror glass: this reduces
the nuisance to the driver caused by theheadlamps from following vehicles, low sun...
Rear view mirror
Manual day/night model
Adjustment
)Adjust the mirror so that the glass is
directed correctl
y in the "day" position.
Day / night position
)Pull the lever to change to the "night"anti-dazzle position. )Push the lever to change to the normal"day" position.In order to ensure optimum visibility during your manoeuvres, the mirror lightens automatically when reversegear is engaged.
Steering wheel adjustment
) When stationary, lower the control lever to yrelease the steering wheel adjustment mechanism. )Adjust the height and reach to suit your driving position. )Pull the control lever to lock the steering wheel
adjustment mechanism.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.
As a safety measure, the mirrors should be adjusted to reduce the "blind spot".
Page 105 of 304
3
103
Comfort
Warning triangle (stowing)
Before leaving your vehicle to set up and install the triangle, put on your high visibility vest.
The dimensions o
f the triangle (once folded) or its storage box must be:
-
A
: length = 438 mm,
-
B: height = 56mm,
- C: width = 38 mm.
To use the triangle, refer to the manufacturer's
instructions.
) Turn the knob to remove the cover. )
Hold the cover and the triangle so that theydo not fall.
The location for a folded trian
gle is in the inner
trim panel of the boot lid.Placing the triangle
in the road
Distance from your vehicle (in metres)
Road
Motorway
DayNight
50 m 80 m
150 m
These are the internationally recognisedvalues.
Use the triangle in line with local driving regulations.
The trian
gle is available as an accessory, contact a PEUGEOT dealer or a qualified
workshop.
) Place the triangle at a distance behindthe vehicle, as shown in the table below,
according to the type of road and the level
of ambient light.
Page 112 of 304
110
Comfort
8. Air distribution adjustment
)Press the corresponding button for:
Windscreen and side windows.
Centre and side vents.
F
ootwells.
To s u i t
your requirements, you cancombine two distribution buttons or select the three distribution modes
simultaneously.
9. Air fl ow adjustment
)Press this "full fan"button toincrease the air flow.
)Press "empty fan"
button to reduce the air flow.
10. Air intake / Air recirculation
)Press this "empty fan"
air flow button until the fan symbol
disappears and "--"
appears.
Switching the system off
)
Press this button for recirculation of the interior air. The indicator
lamp on the button comes on.
Air recirculation enables the passenger compartment to be isolated from exterior
odours and smoke. It is activated automaticallywhen operating the screenwash.
Avoid driving for long periods with the system off (risk of condensation and deterioration of the air quality).
Pressing the "full fan"buttonreactivates the system with the valuesin use at the time it was switched off.
The air flow symbol, the fan, fills progressivelyaccording to the value requested.
Thi
s action switches off all of the functions of the air
conditioning system.
Temperature related comfor t is no longer guaranteed but a slight flow of air, due to theforward movement of the vehicle, can still be felt.
)As soon as possible, press this buttonagain to permit the intake of outside air and prevent the formation of condensation. The
indicator lamp in the button goes off.
Page 115 of 304
3
113
Comfort
) Press this "full fan"button to
increase the air flow. )Press the corresponding button for:
Windscreen and side windows.
Centre and side vents.
Footwells.
To s u i t
your requirements, you cancombine two distribution buttons or select the three distribution modes
simultaneously.
)
Press "empty fan"button to reduce the air flow.
)
Press this "empty fan"
air
flow button until the fan symbol
disappears and "--"
appears.
Automatic air intake modeIt is activated by default with automatic comfort regulation.
9. Air fl ow adjustment
The symbol for air flow, the fan, fills progressively according to the value requested.
Switching the system off
This action switches off all of the functions of
the air conditioning system.
Temperature related comfor t is no longer assured but a slight flow of air, due to thefor ward movement of the vehicle, can still befelt.
Avoid driving for long periods with the system
off (risk of condensation and deterioration of
the air quality). Pressing the "full fan"
buttonreactivates the system with the values in use at
the time it was switched off.
10. Air intake / Air recirculation
Air recirculation enables the passenger compar tment to be isolated from exterior odours and smoke. It is activated automatically
when operating the screenwash. It is inactive
when the ambient temperature is below 5°C to
guard against the risk of misting in the vehicle. ) As soon as possible, press this button
again to permit the intake of outside air and prevent the formation of condensation. The
indicator lamp in the button goes off.
Page 117 of 304
3
115
Comfort
4. Air fl ow adjustment
)
Press this "full fan" button toincrease the air flow.
)
Press this "empty fan" button to
reduce the air flow. The air flow s
ymbol, the fan, fills progressivelyas the fan speed increases.
Deactivating the system
)
Press the "empty fan" air flow
button until the fan disappears and "--" appears.
This action sto
ps all of the functions of the air conditioning system.
Thermal comfor t is no longer controlled.However, a slight air flow may still be felt,resulting from the for ward movement of the
vehicle.
Page 124 of 304
122
Driving
Emergency braking
In the event of a failure of the main servicebrake, a continuous pull on the control lever Awill stop the vehicle.
The dynamic stability control provides stability
during emergency braking.
If the emergency braking malfunctions, a message will be displayed.
I
f a failure of the DSC system is
signalled by the lighting of this
warning lamp, then braking stability is
not
guaranteed.
In this event, stability must be assured by the
driver by repeating alternate "pull-release" actions on the control lever A.
Emergency parking brake release
)if your vehicle has one, take out the vehicle chock B , located behind the rear seats. )On a slope, immobilise the vehicle byplacing a chock in front or behind one of
the front wheels, opposing the slope. On level ground, immobilise the vehicle byplacing a chock in front or behind one of
the front wheels.
In the event o
f fault with the electric parkingbrake or a battery failure, an emergencymechanical control can be used to manually
releasethe parking brake. ) Immobilise the vehicle (or chock it if the
brake pedal has not been released), with
the hybrid system active, place the gear selector in position M or R. )
Switch of the hybrid system, but leave the
ignition on. If you are unable to immobilise
the vehicle, do not operate this control and contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
The emergency braking must only be used in exceptional circumstances.
Page 144 of 304
142
Visibility
Lighting controls System for selection and control of the various front and rear lamps providing the vehicle's lighting and signalling.
Main lighting
There are various lamps on the vehicle:
- sidelamps, to be seen,
- dipped beam headlamps to see without
dazzlin
g other drivers,
- main beam headlamps to see clearly when
the road is clear,
- directional headlamps for improved
visibility when cornering.
Additional lighting
Other lamps are installed to fulfil the requirements of particular driving conditions:
- rear foglamps to better signal the presence of the vehicle in foggy conditions,
- daytime running lamps to be seen duringthe day.
Automatic lighting functions
Various automatic lighting functions are also
available depending on options:
- guide-me-home lighting,
- directional headlamps,
- welcome li
ghting,
- daytime lighting (daytime running lamps),
- automatic illumination of headlamps,
- adaptive lighting.
Page 145 of 304
5
143
Visibility
Selection ring for main lighting mode
Turn the ring to position the symbol required
facing the mark.
Li
ghting off.
Automatic illumination of headlamps.
Sidelamps onl
y.
Dipped or main beam headlamps.
Stalk for switching headlamps
Pull the stalk to switch the lighting between
dipped / main beam headlamps.
In the li
ghting off and sidelamps modes, the driver can switch on the main beam headlamps
temporaril
y ("headlamp flash") by maintaining apull on the stalk.
Displays
Illumination of the corresponding indicator lamp
in the instrument panel confirms the lighting switched on.
