2012 Peugeot 508 boot

44
i
i
!
i
Access
Locking the vehicle
Normal locking
Using the key
)Turn the key towards the rear of the vehicle
to lock the vehicle completely.

Using the remote control
)Press the closed padlock to lock
the vehicle completely.


Using the electronic key
)
With the electronic key in the defined zone,
press with a finger on the door handle(at the markings) to lock the vehicle.) From the boot (SW only), with the electronic key in the defined zone, press a button to lock the vehicle.

Maintaining the locking action (remotecontrol or manual key) automaticallycloses the windows and sunroof.


As a safety measure (children on board), never leave the vehicle without taking your key, even for a shor t period. Guard against theft when the electronickey is in the defined zone with thevehicle unlocked.


Locking is confirmed by fixedlighting of the direction indicators for approximately two seconds.
According to version, the door mirrors fold at the same time.

It is not possible to lock the vehicle if an electronic key is left inside the vehicleor if the ignition is on.


If one of the doors or the boot is stillopen or if an electronic key has been left inside the vehicle, the centrallocking does not take place.
When the vehicle is locked, if it isunlocked inadvertently, it will relock automatically after about thir ty seconds unless a door is opened.
The folding and unfolding of the door mirrors by the remote control can be deactivated by a PEUGEOT dealer.

46
!
!
i
Access
Locking/unlocking from the inside


Automatic central locking of the doors
The doors can lock automatically while driving (speed above 6 mph (10 km/h)).
To activate or deactivate this function, press
and hold the button until a message appears in
the screen.
If the vehicle is deadlocked, the button is not active. In this case, use the key or the remote control to unlock.
Driving with the doors locked may makeaccess to the passenger compartmentby the emergency services moredifficult in an emergency.

Folding the key
)First press this button to fold the key.
If you do not press the button when foldingthe key, there is a risk of damage to the mechanism.

)
Press the closed padlock to
locate your locked vehicle in acar park.
Locating your vehicle
)
Press the button.
This allows the doors and the boot to be lockedor unlocked.
This is indicated b
y lighting of the cour tesylamps and flashing of the direction indicators for a few seconds.
When carrying large objects with theboot open, you can press this button to inhibit the boot open aler t signal. Whenlocking from inside, the door mirrors donot fold.

50
!
Access
System which protects and provides a deterrentagainst theft and break-ins. It provides the
following types of monitoring:






Alarm
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet...


- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or moves inside the vehicle.

- Tilt

The system checks for any change in
the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.


Self-protection function
The system checks for the putting out of ser vice of its components. The alarm is triggered if the battery,the central control unit or the wires of the siren are put out of ser vice or damaged.

For all work on the alarm system, contact a PEUGEOT dealer or a qualified workshop.


Locking the vehicle with full
alarm system


Activation
)Switch off the ignition and get out of the vehicle.
)
Press the locking button on theremote control or lock the vehicle
using the Keyless Entry and Starting system. The monitorin
g system is active: the indicator
lamp on the button flashes once per second.

After the locking button on the remote controlis pressed or the vehicle locked using the
Ke
yless Entry and Starting system, the exterior perimeter monitoring is activated after a delay
of 5 seconds, the interior volumetric monitoring
after 45 seconds and anti-tilt monitoring after 90 seconds.
If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the exterior perimeter monitoring will be activated after a
delay of 45 seconds.
) Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entryand Star ting system.

Deactivation of the volumetric monitoring

The volumetric protection system is
deactivated: the indicator lamp in the
button
goes off.

2
51
Access

Locking the vehicle
w
ith exterior perimeter
monitoring only
Deactivate the interior volumetric and anti-liftmonitoring to avoid unwanted triggering of the alarm in certain cases such as:


- leaving a window par tially open,

- washing your vehicle,

- changing a wheel,

- having your vehicle towed,

- transportation by sea.


Deactivation of the interior volumetric and anti-tilt monitoring
)
Switch of the ignition and within
ten seconds, press this button
until the indicator lamp is on
continuously.) Get out of the vehicle.
)
Press the locking button on
the remote control immediatelyor lock the vehicle using the
Keyless Entry and Starting system.
The exterior perimeter monitorin
g alone is
activated: the indicator lamp in the button
flashes once per second.
To b e effective, this deactivation must be carried
out each time the ignition is switched off.
Reactivation of the interior volumetric and anti-tilt monitoring
Tr iggering of the alarm
This is indicated by sounding of the siren andflashing of the direction indicators for thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times insuccession.
) Press the unlocking button on
the remote control or unlock thevehicle using the Keyless Entry
and Star ting system to deactivate
the exterior perimeter monitoring.
) Press the locking button on the
remote control or lock the vehicleusing the Keyless Entry and Starting system to activate all the monitoring functions.

The indicator lamp in the button
again flashes once per second.


When the vehicle is unlocked usingthe remote control or unlocked
using the Keyless Entry and Starting
system, rapid flashing of the indicator lamp in the button informs you that the alarmwas triggered during your absence. When
the ignition is switched on, this flashing stopsimmediately.

Failure of the remote control

To deactivate the monitoring functions:
)
Unlock the vehicle using the key in thedriver's door lock. )
Open the door; the alarm is triggered. )
Switch on the ignition; the alarm stops.
The indicator lamp in the button switches off.




Locking the vehicle without
activating the alarm
)
Lock or deadlock the vehicle using the key
in the driver's door lock.




Operating fault


When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a fault in the system.
Have it checked by a PEUGEOT dealer or a qualified workshop.


* Accordin
g to country.


Automatic activation *


2 minutes after the last door or the boot is closed, the system is activated automatically. )
To avoid triggering the alarm on enteringthe vehicle, first press the unlocking button on the remote control or unlock the vehicleusing the Keyless Entry and Star ting system.

54
Access











Boot
Saloon
)After unlocking the vehicle completely using the remote control or the key, press
this button.



SW
)
After unlocking the vehicle completelyusing the remote control or the key, press
at the top (on lever A ), and raise theAtailgate.

From the inside

Hold this button down until unlocking of theboot is heard.
Opening


Closing
)Lower the tailgate using the interior grabhandle.
If the tailgate is not closed correctly:


- when the en
gine is running
,
this warning lamp and amessage in the instrument panelscreen appear for a few seconds,
-when the vehicle is moving(speed above
6 mph (10 km/h)), this warning lamp and a message, accompanied by an audiblesignal, appear in the instrument panel
screen for a few seconds.

56
!
Access
) Press this button C
to close thetailgate electrically.
Do not hinder closin
g of the tailgate: any
obstacle to closing causes the tailgate to stopand rise a few centimetres automatically.To close the tailgate manually: move the
tailgate slightly up then down to disengage it
from its drive then lower it until closed.
To avoid the risk of injury, ensure
that no one is close to the rear of thevehicle when opening or closing the tailgate.

While electric opening or closing of the tailgate
is in progress, you can stop its movement at
an
y time: ) press the interior button or button A
on
the remote control or button Bor C on thetailgate.


Stopping the opening or
closing
Ad
justing the opening
height

The maximum opening height of the tailgate can be set and memorised (restricted overheadclearance, ...).
This memorisation is done in two steps,by successive presses on button C
:


- during opening, a first press stops the
tailgate at the desired height,

- a second maintained press memorises the
position of the tailgate; an audible signal confirms the memorisation.
To delete this memorisation, make a newmaintained press until the audible signal isheard.
"Boot open" warning
With the engine running or when the vehicle ismoving, if the tailgate is not properly closed,
a message accompanied by an audible signal
(from 6 mph (10 km/h)) is displayed in the
instrument panel screen.

2
57
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in
the event of a battery or central locking fault.
Unlocking
)Fold back the rear seats to gain access to
the lock from inside the boot.)Insert a small screwdriver into hole Aof
the lock, then move the lever to the le
ft tounlock the boot.

3
69
!
Comfort











Rear seats
Bench seat the left-hand (1/3) or right-hand (2/3) section of which can be folded to adapt the boot load space.


Outer rear seat head restraints

These have a high position (comfort and safety), a low position (rear visibility) and can also be removed.
T
o remove a head restraint: )pull the head restraint fully upwards, )then, press the lug A .

Never drive with rear passengers when the head restraints are removed; thehead restraints must be in place and in the high position.
Folding the seat from
the boot
)
Check that nothing is preventing the seat back from folding (head restraint, seat belts, ...),)
check also that no object on or under theseat could hinder its movement,
)
pull the control from the boot and push the seat backrest.

(SW)

Each section of the bench seat (1/3 or 2/3) hasits own control to release the seat back and its
seat cushion from the boot.