2012 PEUGEOT 4008 instrument panel

114
Driving
Gear lever positions
P : park.
Immobilisation of the vehicle, parking brake applied or not.R: reverse gear.
With the vehicle stationary, keep your foot
on the brake pedal and push the gear lever forwards.
N: n
eutral.D: driving in automated mode.
Move the lever backwards to select this mode.
+/-: manual mode with sequential gear changing.
Move the lever backwards, then to the left toselect this mode, then:
- push forward to change up,
- pull backward to change down.
+
: gear changing in manual mode.
Press behind the "+/OFF"
steering mounted control paddle to change up.-: gear changing in manual mode.
Press behind the "-" steering mounted control
paddle to change down.

Functions of the steering
mounted control paddles
Press the brake pedal firmly whilestarting the engine.


Moving off
)Star t the engine. From position
P
, parking brake applied:P
Press the brake pedal firmly to
release the gear lever.
)Select first gear (position Dor +/- ) or reverse (position R ). R"D"
or "1"
or "R"
appear in the instrumentpanel screen. )Release the parking brake, the vehiclemoves off on its own.

115
4
Driving

Stopping - Starting on a slope
It is essential to use the parking brake to
hold the vehicle on a slope and not the accelerator pedal. When starting on a slope, accelerate gradually
while releasing the parking brake.
Manual mode
) Select position +/- . )
Use the steering mounted controls or thegear lever to change gear.The gears engaged appear in succession in theinstrument panel screen.The gear change instructions are only carried
out if the engine speed permits it.
You can change gear without taking your foot
off the accelerator pedal.
When deceleratin
g, the gearbox changes down automatically.
With the vehicle stationary, first gear is
engaged.

Automated mode
)
Select position D .
"D"
appears in the instrument panel screen.
The gearbox operates in auto-active mode,
without any action on the par t of the driver.
It continuously selects the gear most suited to
the conditions of:


- driving style,

- road characteristics,

- v
ehicle load.
To o p t i m i s e d r i v i ng comfor t and obtain the most suitable gear, avoid sharp variations in the
pressure on the accelerator pedal.
For the best acceleration, whenover taking another vehicle, for example,press firmly on the accelerator going beyond the point of resistance.

116
Driving
Manual gear changing
In the automated mode, you can take over
control temporarily at any time using thesteering mounted controls.
The use of these controls permits manualselection of the gears in situations whichrequire a faster change down than that offered
in automated mode (arrival at a roundabout, exit from a car park with a steep gradient,
over taking...).
The gearbox engages the gear requested if
the engine speed permits it. The gear engaged appears.
To return to the automated mode, do one of thefollowing:
- press the back of the "+/OFF"steering mounted control 3for approximately2 seconds,
- move the gear lever quickly towardsposition +/-
and then return it to position D ,
- stop the vehicle.


Stopping the vehicle
Operating fault

With the ignition on, if the message "Slow
down"
or "Service required"
appears in
the instrument panel screen, this indicates a
gearbox malfunction.
When a message is displayed, carry out thefollowing operations:


- slow down and stop your vehicle in a safe place,

- place the lever in position P
and let the engine run,

- open the bonnet to allow the engine to cool.
If the message disappears for a long period, you can set off again.
If the message remains displayed or appears frequently, contact a PEUGEOT dealer or aqualified workshop without delay. Before switchin
g off the engine, you must place
the gear lever in position P.P You must apply the parking brake to immobilise
the vehicle.

118
Driving





Hill start assist
System which keeps your vehicle immobilised
temporarily (approximately 2 seconds) whenstarting on a gradient, the time it takes to
move your foot from the brake pedal to the accelerator pedal.
This function is only active when:
- the vehicle is completely stationary, withyour foot on the brake pedal,
- when cer tain conditions of gradient are met,
- with the driver’s door closed.
The hill start assist function cannot bedeactivated.
On an ascendin
g slope, with the vehiclestationary, the vehicle is held for a brief moment when you release the brake pedal:

- if you are in first gear or neutral with a
manual gearbox,

- if you are in position Dwith the CVT gearbox.


Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, thevehicle is held for a brief moment when you release the brake pedal.
Do not leave the vehicle while it is beingheld in the hill star t assist phase.
If you need to leave the vehicle whilethe engine is running, apply the parking brake.



Operating fault

If a fault occurs with the system, this warninglamp comes on, accompanied by a message
in the instrument panel screen. Contact a
PEUGEOT dealer or a qualified workshop to have the system checked.
When the engine is not running,including periods on standby withthe Stop & Start (AS&G) system, thefunction is not operative.

119
4
Driving








Stop & Start (Auto Stop & Go) function


Operation


Going into engine STOP mode
The "AS &G "
warning lamp comes on in
the instrument panel or the instrument panel screen and the engine goes intostandby after a few seconds:


- with a manual
gearbox
, with the vehicle stationary and your foot on the brake, whenyou put the gear lever into neutral andrelease the clutch pedal.

Never refuel with the engine in STOPmode; you must switch off the ignition with the key or the START/STOP button.
When the engine is stopped automatically, the operation of certainvehicle systems, such as for example,braking, power steering... are modified. Take care.


Special cases: STOP mode notavailable
STOP mode is not invoked when:


- the driver's seat belt is not fastened,

- the bonnet is open,

- the vehicle has not exceeded 3 mph (5 km/h) since the last engine start,

- the vehicle has restarted less than10 seconds ago,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...) where the engine isneeded to assure control of a system.

- th
e "AS&G"warning lamp is
flashing in the instrument panel.
This operation is perfectl
y normal.

The Stop & Star t (Auto Stop & Go) function puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, or other...). Theengine restarts automatically as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t (Auto Stop & Go) function reduces fuel consumption and exhaust emissions as well as the noise level whenstationary.

120
Driving
The "AS&G"
warning lamp goes off
and the engine starts automatically:
- with a manual gearbox
, when you fullydepress the clutch pedal.
For safet
y reasons or to ensure smooth
operation, STA R T m o d e i s i n v o ke d
automatically when:

Special cases: START invoked
automaticall
y
-the speed of the vehicle exceeds 2 mph (3 km/h),
- some special conditions (battery charge,engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
If the system has been deactivated inSTOP mode, the engine will not star t.
At any time, press the "AS &G O FF "
switch todeactivate the system.


Deactivation
In this case the "AS&G"warning lamp flashes for few seconds, then goes off.
This operation is per fectly normal.
This is confirmed by the "AS&G OFF"warning lamp coming on in the instrument panel or instrument panel screen.

121
4
Driving
The system is reactivated automatically at every new star t using the key or the STA R T/STOP button.

Reactivation

Press the "AS&G OFF"switch again.
The s
ystem is active again; this is confirmed by
the "AS &G O FF "
warning lamp going off in the
instrument panel or instrument panel screen.
Operating fault
In the event of a malfunction with the system,
the "AS&G OFF"warning lamp flashes in theinstrument panel or instrument panel screen,and the system no longer operates.
have it checked by a PEUGEOT dealer or a qualified workshop.
This system requires a specific battery with a special specification and technology (reference numbersavailable from a PEUGEOT dealer or aqualified workshop).
Fitting a battery not listed by
PEU
GEOT introduces the risk of malfunction of
the system.

Maintenance

The "Auto Stop & Go" system makes use of advanced technology. All work on this type of battery must be doneonly by a PEUGEOT dealer or aqualified workshop.
In the event o
f a fault in STOP mode, the
vehicle may stall. The following warning lampscome on in the instrument panel or instrumentpanel screen:
It is then necessar
y to switch off the ignition,
then restart the engine using the key or theSTA R T/STOP button.

122
Driving





Four wheel drive system
System which permits the selection of a transmission mode in relation to the driving conditions.
Three transmission modes are available and can be selected manually by the driver in accordance with his requirements.
You can chan
ge transmission mode when stationary or while driving.
The transmission mode can be selected byturning the control A .

Selecting the transmission
mode


4WD AUTO (position 1)

The vehicle operates with four wheel drive and
provides optimum traction for all levels of grip.
This is the vehicle's normal and regular
operating mode, the distribution of the torque between the front and rear axles is controlled
automatically.
The distribution favours the front wheels,
the transfer of torque to the rear wheels is
mana
ged electronically by the control unit
in relation to the level of grip, so providing
optimum road holding.


4WD LOCK (position 2)

The vehicle operates with four wheel drive in
this mode also.
It is recommended when grip is par ticularly
poor or di
fficult (sand, mud, slopes, ...).


2WD (position 3)

The vehicle operates with front two wheel drive.
This is suitable for use on a tarmac roads or
where the driver considers that there is no riskof loss of grip (dry road).
Display in the instrument panel
The transmission mode is displayed in the
form of an intermittent display in the instrumentpanel screen when the transmission mode is
selected.
The selection of this mode isrecommended when the level of grippermits.